环球插件机名词解释

1、环球插件机名词解释一.胶水、润滑油类名称物料号Loctite 222UIC# BLKM07389螺丝胶Loctite 242UIC# BLKM07402螺丝胶O-ring lubricantUIC#BLKM07387汽缸油（密封油）Magna lubeUIC#40833809绿油AnderolUIC#40833833Kluber NBU15 GreaseUIC#40833826白油Kluber Syntheso D32UIC#40833829高温油Kendall Super BlueUIC#BLKM07680超级蓝油SAE #10 DTE-lite non-detergent oilUIC40

2、83382710号油5W OIL5号油10W OIL10号油二.机械类Cutter Station切断站CTA(Component Transfer Assembly)元件传送单元BEC (Board Error Correction)板误差校正（光校）Insertion Head插件头Cutter Head切断头Dispensing Head分配头（料站）Pneumatic Oilers油雾器Positioning System定位系统（X-Y工作台）Sequencer Assyembly编序装置（编序链条）Insertiong Head Drive Assembly插件头驱动装置The G

3、rease Seal Block润滑密封块Chain Tension(Spring Loaded Sprocket Assembly)链条涨紧装置Chain Unloader链条卸料Clinch Scrap Bowl切弯废料桶Machine Interlocks机器联锁Component Conditioner元件编带导向Chain To Chain Assembly链条与链条交接装置Chain Tensioner Assembly链条涨紧装置Drive Assembly驱动装置Clip Assembly链夹装置Clinch Assembly切断打弯装置（剪角器）Jumper Wire Ass

4、embly跳线装置Covers盖板Clinch Air Cylinder切弯气缸X And Y Ball ScerwX-Y轴丝杆Rotary Table Air Motor Drive Wheel驱动轮Rotary Table Lock Assembly转台锁装置Drive Motor驱动马达Chain Ldler Assembly链条堕轮装置Centering Cam对中凸轮Carrier Clip料夹Head Span头跨距Anvil Span切弯跨距X AxisX轴Y AxisY轴Sequencer Head编序链Head Chain头链三.电器部分Work Lamp工作灯PB Pane

5、l Assembly按键面板Power Chassis Assembly电源箱VME Chassis AssemblyVME机箱装置VMEBUS(Versa Module European Bus)欧洲工业保准AC Chassis Assembly交流机箱装置Servo Chassis Assembly伺服放大器机箱装置Machine Light Tower机器灯塔I/O Box Assembly输入/输出机箱装置Fuse保险丝Palm Switch急停开关Fan Panel风扇Refire Assembly缺料检测装置四.I/O BOXMIT Board机器接口翻译板Multi-Input

6、Board多路输入信号板32 DC Output Board32路直流输出板BEC (Board Error Correction) BoardBEC光校板五.VME机箱Radisys Embedded PC Board (1 槽)CPU主板:输入信号：串行通讯接口、鼠标、键盘，机器管理 信息，网路通讯灯。输出信号：串行通讯接口、实时控制、打印机、网路通讯等。Motion Controller CPU Real Time Controller Power PC Board(2 槽)机器实时控制CPU板：输入信号：程序信息，机器操作，机 器信号反馈等。输出信号：机器控制信息、轴位置指令等。此板机

7、器自动运行时候工作、诊断系统内此板不工作Motion Controller (UIMC)(3 槽)动作控制器。输入信号：轴位置指令、编码器与极限开关的反馈信号。输出信号：伺服放大器速度信号、BEC启动信号等一块UIMC板的控制4个轴。轴向机：X Axis、Y Axis、Head Axis、Anvil Axis径向机：X Axis、Y Axis、Clinch Vertical Axis Clinch Theta AxisMotion Controller (UIMC)(4 槽)动作控制器。输入信号：轴位置指令、编码器与极限开关的反馈信号。输出信号：伺服放大器速度信号一块UIMC板的控制4个轴。轴

8、 向机:Insert Span、Clinch Span、Head Chain、Sequencer Chain径向机：Head Vertical、Sequencer Chain、Insert Head Theta机器内各气管示意黑色长有气管此气管不受E-PLAM控制，机器后部气 阀开启，此气管即有气。蓝色信号气管此气管受各电磁阀控制黄色排气管6241F剪角器切刀速度同步检查按下急停开关。进入诊断系统内。点击进入 Critical Axis Setup。Zero Anvil Driver Go To UpZero Anvil Span点击 Diagnostics Rapid Motiong Timing在 Control Bit 部分选择 Section :Inserter DSF :1 Clinch In在 Change Of State 1(Input)部分选择 Section :Inserter DSF :1 Clinch In L在 Change Of State 1(Input)部分选择 Section :Inserter DSF :1 Clinch In R十.在 Execution Control 部分点击 Follows Control Contin