下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、- No communications with the battery control unit -主题编号GI54.15-P-012348车型3 设计组54.15 Fuse and relay box 日期04-24-2007 有效性Model 211.#改变的原因Text revised投诉 Customer complaint: Implausible red fault message (Battery/alternator, locate workshop) is displayed in the instrument cluster. In the DAS quick test
2、the battery control unit (BCU, N82) is not detected and is marked in the quick test printoutwith a !.If this situation occurs, the BCU must not be replaced immediately, but the steps described in the remedy below must be applied first.原因 Under certain circumstances (battery exhausted, jump start) th
3、e software of the BCU mayhang, preventing the BCU from participating in CAN communications.As a result the red combination message Battery/alternator, locate workshop is displayed.In the DAS quick test this state is indicated by a ! by the BCU. Other control units (e.g. instrument cluster, SAM) also
4、 have the current or stored fault CAN communication with the BCU control unit is disrupted.修改 If the communication errors with the BCU listed above are current or stored, a circuit 30 reset of the BCU must be performed by disconnecting the plug at the control unit itself for at least 5minutes (cauti
5、on: switch off the ignition beforehand).- Operation number: 542306 Performing battery control unit reset, 2 WUThen perform the quick test again. If the battery control unit is now detected in the quick test,there is no defect in the battery control unit, but the problem is the abovesoftware crash. I
6、n other control units (e.g. IC, SAM), the circuit 30 reset of theBCU causes the displayed fault CAN communication with the BCU control unit is disrupted to change from current to stored.- Operation number: 541011 Performing quick test, 4 WUNote: This is no reason to replace the BCU because the BCU h
7、as executed a correct protection function and operates perfectly normally again after the circuit 30 reset. A new BSG would also behave exactly the same under the same conditions (battery deep discharge, starting aid).症状 症状Overall vehicle / Power supply / Battery / On-board electrical system / Batte
8、ry/on-board electrical system indicator lamp / Battery charge indicator/consumer shutoff / Illuminates redOverall vehicle / Power supply / Battery / On-board electrical system / Battery/on-board electrical system display message / Battery/Alternator - Serviced Required控制单元/故障代码 控制单元故障代码故障代码描述IC-Inst
9、rument cluster (KI4) 9123 Event:Fault in CAN communication with control unit Vehicle power supply control module. BCM-Battery control module (BSG2) 9040 Terminal 30: undervoltage Dr-side SAM-Driver signal acquisition and actuation module (SAMF3) 909A Event:Fault in CAN communication with control unit BCM. REAR SAM-Rear signal acquisition and actuation module (SAMH4
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 2024届山东省日照市高三下学期4月二模物理试题(解析版)
- 中国绿色产业园投资规划及发展潜力分析报告2024-2030年
- 2023年花草茶项目调研分析报告
- 2023年超深井用高抗挤毁石油管钢项目调研分析报告
- 2024标志牌制作安装合同范本
- 2023年机械化农业及园艺机具项目分析评估报告
- 第17课《昆明的雨》教学实录
- 国旗下的讲话安全禁毒
- 网络分片与软件定义网络融合
- 2024年合同管理考点 施工评标办法试题
- 电梯行业安全培训课程
- 医疗器械工作人员的综合培训方案
- 物联网应用技术专业介绍
- 科室质量管理手册-医技医辅科室(药剂科、放射科、功能影像科、检验科)
- 《额尔古纳河右岸》读书分享主题班会
- 计算机组成与设计(第五版)
- 《一生中最爱》谐音歌词
- 室内装修 投标方案(技术方案)
- 东方财富杯知识比拼题库
- 固废物联网智能管理平台解决方案
- 2023保密知识培训课件
评论
0/150
提交评论