[资料]联发MTK专业校准-cfg配置文件2012

1、资料 联发_MTK专业校准-cfg配置文件2012META versionMETA version= ver 6.1.08960 Initialization补偿8960 GPIB Address =GPIB0:15:INSTRTime Out =5000GSM400 cable loss = -1.0GSM850 cable loss = -0.6GSM900 cable loss = -0.6DCS1800 cable loss = -0.8PCS1900 cable loss = -0.8WCDMA BAND1 input cable loss = -1.2WCDMA BAND

2、1 output cable loss = -1.2WCDMA BAND2 input cable loss = -1.2WCDMA BAND2 output cable loss = -1.2WCDMA BAND5 input cable loss = -0.7WCDMA BAND5 output cable loss = -0.7WCDMA BAND8 input cable loss = -0.7WCDMA BAND8 output cable loss = -0.7CMU200 Initialization损耗CMU200 GPIB Address =GPIB0:20:INSTRTim

3、e Out =5000GSM400 input cable loss = 0.7GSM850 input cable loss = 0.6GSM900 input cable loss = 0.6DCS1800 input cable loss = 0.8PCS1900 input cable loss = 0.8GSM400 output cable loss = 0.7GSM850 output cable loss = 0.6GSM900 output cable loss = 0.6DCS1800 output cable loss = 0.8PCS1900 output cable

4、loss = 0.8WCDMA BAND1 input cable loss = 1.2WCDMA BAND1 output cable loss = 1.2WCDMA BAND2 input cable loss = 1.2WCDMA BAND2 output cable loss = 1.2WCDMA BAND5 input cable loss = 0.7WCDMA BAND5 output cable loss = 0.7Frequency Bank;bank = 0x1Cbank = 0x1E850/900/1800/1900频率;bank = 0x1A;bank = 0x0C; G

5、SM450 0x01; GSM850 0x02; GSM900 0x04; DCS1800 0x08; PCS1900 0x10C0 for each Bankarfcn_C0_GSM = 65900信道arfcn_C0_DCS = 700arfcn_C0_PCS = 660arfcn_C0_GSM850 = 190Downlink powerP_DL = -60AFC Calibration;AFC_BAND: GSM, DCS, PCS, GSM850AFC_BAND = GSM以900频率校准AFC_ARFCN = 65900信道N_AFC = 20EXTRA_FB = 5DAC1=35

6、00校准的初始值1DAC2=4500校准的初始值2CRYSTAL_DAC1=3500CRYSTAL_DAC2=4500AFC tableMAX_INIT_AFC_DAC = 6000AFC最大值MIN_INIT_AFC_DAC = 3000AFC最小值MAX_AFC_SLOPE = 4.0AFC斜率最大值MIN_AFC_SLOPE =2.0AFC斜率最小值Crystal AFC Calibration晶振/晶体校准;CRYSTAL_AFC_BAND: GSM, DCS, PCS, GSM850CRYSTAL_AFC_BAND = GSMCRYSTAL_AFC_ARFCN = 65CRYSTAL

7、_AFC_GSM850_PCL  = 14CRYSTAL_AFC_GSM900_PCL  = 14CRYSTAL_AFC_DCS1800_PCL = 7CRYSTAL_AFC_PCS1900_PCL = 7CRYSTAL_AFC_CAL_DAC = 4096CRYSTAL_AFC_CHECK_DAC1 = 0CRYSTAL_AFC_CHECK_DAC2 = 8191CRYSTAL_AFC_MIN_FREQ_ERR_PPM = -10.0CRYSTAL_AFC_MAX_FREQ_ERR_PPM = 10.0CRYSTAL_AFC_MAX_AFC_TRACK

8、_INIT_FREQ_ERR = 20CRYSTAL_AFC_FREQ_ERR_MEASUSE_COUNT = 10CRYSTAL_AFC_TRX_OFFSET_RECURSIVE_TIMES = 20RX measurement samplesN_PM = 5M_PM = 4RX path loss tableAGC接收损耗/补偿校准GSM850_MAX_RX_LOSS = 3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.000,3.0000,850高频AGC最大值GSM850_MIN_RX_LOSS = -3.00

9、0,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.0000,850高频AGC最小值GSM900_MAX_RX_LOSS = 3.000,3.000,3.0000,3.000,3.000,3.0000,3.000,3.000,3.0000,3.000,3.000,3.0000,GSM900_MIN_RX_LOSS = -3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.000,-3.0000,DCS180

10、0_MAX_RX_LOSS = 5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,DCS1800_MIN_RX_LOSS = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,PCS1900_MAX_RX_LOSS = 5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,PCS

11、1900_MIN_RX_LOSS = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,GSM850_MAX_RX_LOSS_MIDDLE = 5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.0000,850中频AGC最大值GSM850_MIN_RX_LOSS_MIDDLE = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,

12、-5.000,-5.000,-5.000,-5.0000,850中频AGC最小值GSM900_MAX_RX_LOSS_MIDDLE = 5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,GSM900_MIN_RX_LOSS_MIDDLE = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,DCS1800_MAX_RX_LOSS_MIDDLE = 5.000,5.000,5.

13、0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,DCS1800_MIN_RX_LOSS_MIDDLE = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,PCS1900_MAX_RX_LOSS_MIDDLE = 5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,PCS1900_MIN_RX_LOSS

14、_MIDDLE = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,GSM850_MAX_RX_LOSS_LOW = 5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.000,5.0000,850低频AGC最大值GSM850_MIN_RX_LOSS_LOW = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-

15、5.000,-5.0000,850低频AGC最小值GSM900_MAX_RX_LOSS_LOW = 5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,5.000,5.000,5.0000,GSM900_MIN_RX_LOSS_LOW = -5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.000,-5.0000,DCS1800_MAX_RX_LOSS_LOW = 6.000,6.000,6.0000,6.000,6.000,6.0000,

16、6.000,6.000,6.0000,6.000,6.000,6.0000,DCS1800_MIN_RX_LOSS_LOW = -6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.0000,PCS1900_MAX_RX_LOSS_LOW = 6.000,6.000,6.0000,6.000,6.000,6.0000,6.000,6.000,6.0000,6.000,6.000,6.0000,PCS1900_MIN_RX_LOSS_LOW = -6.000,-6.000,-6.000,-6

17、.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.000,-6.0000,TX IQ tableTX_IQ_MEASUREMENT_COUNT = 20;TX_IQ_BAND: GSM, DCS, PCS, GSM850TX_IQ_BAND = GSMTX_IQ_ARFCN = 65TX_IQ_PCL = 15TX_IQ_DC_OFFSET_MAX = -38TX_IQ_GAIN_IMBALANCE_MAX = -35; The following setting is for MT6140BTX_IQ_BAND_HIGH = DCSTX_IQ

18、_ARFCN_HIGH = 700TX_IQ_PCL_HIGH = 5TX_IQ_DC_OFFSET_MAX_HIGH = -38TX_IQ_GAIN_IMBALANCE_MAX_HIGH = -35TX PCL tableAPC全等级功率校准GSM850_CAL_PCL = 17, 12, 5,GSM850_2CAL_PCL = 19, 5,GSM850_PCL    = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,              &#

19、160;         GSM850_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,                     GSM850_MAX_P = 6.5,7.8,9.8,11.8,13.8,15.8,17.8,19.8,21.8,23.8,25.8,27.8,29.8,31.3,32.5,850全等级最大功率GSM850_WAN

20、TED_P = 5.0,7.0,9.0,11.0,13.0,15.0,17.0,19.0,21.0,23.0,25.0,27.0,29.0,30.5,32.0,850全等级期望功率GSM850_MIN_P = 3.5,6.2,8.2,10.2,12.2,14.2,16.2,18.2,20.2,22.2,24.2,26.2,28.2,29.7,31.5,850全等级最小功率   GSM850_C = 12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,         &#

21、160;                      GSM850_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,  GSM850_EPSK_CAL_PCL = 12, 10, 6,GSM850_EPSK_2CAL_PCL = 19, 5,  GSM850_EPSK_4CAL_PCL = 19,14,12,8,      

22、0;               GSM850_EPSK_PCL    = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,                        GSM850_EPSK_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,

23、7,6,5,                     GSM850_EPSK_MAX_P = 6,8,10,12,14,16,18,20,22,24,26,27.1,27.1,27.1,27.1,GSM850_EPSK_WANTED_P = 5,7,9,11,13,15,17,19,21,23,25,26.5,26.5,26.5,26.5,             

24、  GSM850_EPSK_MIN_P = 4,6,8,10,12,14,16,18,20,22,24,26,26,26,26,GSM850_EPSK_C = 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,                               GSM850_EPSK_CORRECTION = 0

25、,0,0,0,0,0,0,0,0,0,0,0,0,0,0,      GSM900_CAL_PCL = 17, 12, 5,GSM900_2CAL_PCL = 19, 5,GSM900_PCL    = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM900_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM900_MAX_P = 6.5,7.8,9.8,11.8,13.8,15.8,17.8,19.8,21.8,23.8,25.8,27

26、.8,29.8,31.3,32.5,GSM900_WANTED_P = 5.0,7.0,9.0,11.0,13.0,15.0,17.0,19.0,21.0,23.0,25.0,27.0,29.0,30.5,32.0,GSM900_MIN_P = 3.5,6.2,8.2,10.2,12.2,14.2,16.2,18.2,20.2,22.2,24.2,26.2,28.2,29.7,31.5,   GSM900_C = 12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,GSM900_CORRECTION = 0,0,0,0,0,0,0

27、,0,0,0,0,0,0,0,0,GSM900_EPSK_CAL_PCL = 12, 10, 6,GSM900_EPSK_2CAL_PCL = 19, 5,GSM900_EPSK_4CAL_PCL = 19,14,12,8,GSM900_EPSK_PCL    = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM900_EPSK_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,GSM900_EPSK_MAX_P = 6,8,10,12,14,16,18,20,22,24,26,27

28、.1,27.1,27.1,27.1,GSM900_EPSK_WANTED_P = 5,7,9,11,13,15,17,19,21,23,25,26.5,26.5,26.5,26.5,   GSM900_EPSK_MIN_P = 4,6,8,10,12,14,16,18,20,22,24,26,26,26,26,GSM900_EPSK_C = 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,GSM900_EPSK_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,DCS1800_CAL_PCL

29、 = 13, 8, 1,DCS1800_2CAL_PCL = 15, 0,DCS1800_PCL    = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1800_CHECK_PCL  = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1800_MAX_P = 3.5,4.3,5.8,7.3,8.8,10.8,12.8,14.8,16.8,18.8,20.8,22.8,24.8,26.8,28.3,29.5,DCS1800_WANTED_P = 2.0,3.5,5

30、.0,6.5,8.0,10.0,12.0,14.0,16.0,18.0,20.0,22.0,24.0,26.0,27.5,29.0,DCS1800_MIN_P = 0.5,2.7,4.2,5.7,7.2,9.2,11.2,13.2,15.2,17.2,19.2,21.2,23.2,25.2,26.7,28.5,DCS1800_C = 12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,12, DCS1800_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,DCS1800_EPSK_CAL_PCL = 8,

31、 6, 2,DCS1800_EPSK_2CAL_PCL = 15, 0,DCS1800_EPSK_4CAL_PCL = 15,8,6,2,DCS1800_EPSK_PCL    = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1800_EPSK_CHECK_PCL  = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1800_EPSK_MAX_P = 1,3,5,7,9,11,13,15,17,19,21,23,25,26.5,26.5,26.5,DCS1800

32、_EPSK_WANTED_P = 0,2,4,6,8,10,12,14,16,18,20,22,24,25.5,25.5,25.5,DCS1800_EPSK_MIN_P = -1,1,3,5,7,9,11,13,15,17,19,21,23,25,25,25,DCS1800_EPSK_C = 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,DCS1800_EPSK_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,PCS1900_CAL_PCL = 13, 8, 1,PCS1900_2CAL_PCL = 1

33、5, 0,PCS1900_PCL    = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,PCS1900_CHECK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,DCS1900_MAX_P = 3.5,4.3,5.8,7.3,8.8,10.8,12.8,14.8,16.8,18.8,20.8,22.8,24.8,26.8,28.3,29.5,DCS1900_WANTED_P = 2.0,3.5,5.0,6.5,8.0,10.0,12.0,14.0,16.0,18.0,20.0,22

34、.0,24.0,26.0,27.5,29.0,DCS1900_MIN_P = 0.5,2.7,4.2,5.7,7.2,9.2,11.2,13.2,15.2,17.2,19.2,21.2,23.2,25.2,26.7,28.5,PCS1900_C = 12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,12,PCS1900_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,PCS1900_EPSK_CAL_PCL = 8, 6, 2,PCS1900_EPSK_2CAL_PCL = 15, 0,PCS1900_EPSK_

35、4CAL_PCL = 15,8,6,2,PCS1900_EPSK_PCL    = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,PCS1900_EPSK_CHECK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,PCS1900_EPSK_MAX_P = 1,3,5,7,9,11,13,15,17,19,21,23,25,26.5,26.5,26.5,PCS1900_EPSK_WANTED_P = 0,2,4,6,8,10,12,14,16,18,20,22,24,25.5,25.5

36、,25.5,PCS1900_EPSK_MIN_P = -1,1,3,5,7,9,11,13,15,17,19,21,23,25,25,25,PCS1900_EPSK_C = 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,PCS1900_EPSK_CORRECTION = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,GSM850_SUBBAND_FLATNESS_CHECK_PCL=5GSM900_SUBBAND_FLATNESS_CHECK_PCL=5DCS1800_SUBBAND_FLATNESS_CHECK_PCL=0P

37、CS1900_SUBBAND_FLATNESS_CHECK_PCL=0GSM850_SUBBAND_FLATNESS_RANGE=0.2GSM900_SUBBAND_FLATNESS_RANEG=0.2DCS1800_SUBBAND_FLATNESS_RANGE=0.2PCS1900_SUBBAND_FLATNESS_RANGE=0.2TXPC_CAL_TEMP=25; check margin; default 900TXPC_GMSK_MAX_APC_DAC=900; default 30TXPC_GMSK_MIN_APC_DAC=30; default 895TXPC_EPSK_MAX_

38、APC_DAC=895  default 192TXPC_EPSK_MIN_APC_DAC=192; default 10 (unit: dB)TXPC_MAX_SUBBAND_COMP=10.0; default  -10 (unit: dB)TXPC_MIN_SUBBAND_COMP=-10.0TSC=5Recursive Times=50APC Delta=0.1; for Skyworks 77318, 77328, 77506 only功放Skyworks必须参数SKY77328_DAC_Delta=10SKY77328_GSM850_M &#

39、160;= 16.8SKY77328_GSM850_TARGET_PCL  = 19SKY77328_GSM850_MAX_HIGH_APC_DC_OFFSET_P = -3.5SKY77328_GSM850_WANTED_HIGH_APC_DC_OFFSET_P  = -4SKY77328_GSM850_MIN_HIGH_APC_DC_OFFSET_P = -4.5SKY77328_GSM850_MAX_LOW_APC_DC_OFFSET_P = -3.5SKY77328_GSM850_WANTED_LOW_APC_DC_OFFSET_P = -4SK

40、Y77328_GSM850_MIN_LOW_APC_DC_OFFSET_P = -4.5SKY77328_GSM900_M  = 16.8SKY77328_GSM900_TARGET_PCL  = 19SKY77328_GSM900_MAX_HIGH_APC_DC_OFFSET_P = -3.5SKY77328_GSM900_WANTED_HIGH_APC_DC_OFFSET_P  = -4SKY77328_GSM900_MIN_HIGH_APC_DC_OFFSET_P = -4.5SKY77328_GSM900_MAX_LOW_AP

41、C_DC_OFFSET_P = -3.5SKY77328_GSM900_WANTED_LOW_APC_DC_OFFSET_P = -4SKY77328_GSM900_MIN_LOW_APC_DC_OFFSET_P = -4.5SKY77328_DCS1800_M = 17.78SKY77328_DCS1800_TARGET_PCL = 15SKY77328_DCS1800_MAX_HIGH_APC_DC_OFFSET_P = -3.5SKY77328_DCS1800_WANTED_HIGH_APC_DC_OFFSET_P = -4SKY77328_DCS1800_MIN_HIGH_APC_DC

42、_OFFSET_P = -4.5SKY77328_DCS1800_MAX_LOW_APC_DC_OFFSET_P = -3.5SKY77328_DCS1800_WANTED_LOW_APC_DC_OFFSET_P = -4SKY77328_DCS1800_MIN_LOW_APC_DC_OFFSET_P = -4.5SKY77328_PCS1900_M = 17.78SKY77328_PCS1900_TARGET_PCL = 15SKY77328_PCS1900_MAX_HIGH_APC_DC_OFFSET_P = -3.5SKY77328_PCS1900_WANTED_HIGH_APC_DC_

43、OFFSET_P = -4SKY77328_PCS1900_MIN_HIGH_APC_DC_OFFSET_P =-4.5SKY77328_PCS1900_MAX_LOW_APC_DC_OFFSET_P = -3.5SKY77328_PCS1900_WANTED_LOW_APC_DC_OFFSET_P = -4SKY77328_PCS1900_MIN_LOW_APC_DC_OFFSET_P = -4.5MIN_GMSK_GSM850_APC_DAC = 100MIN_GMSK_GSM900_APC_DAC = 100MIN_GMSK_DCS1800_APC_DAC = 80MIN_GMSK_PC

44、S1900_APC_DAC = 80MAX_GMSK_GSM850_APC_DAC = 550MAX_GMSK_GSM900_APC_DAC = 550MAX_GMSK_DCS1800_APC_DAC = 550MAX_GMSK_PCS1900_APC_DAC = 550;MIN_GMSK_GSM850_APC_DAC = 50;MIN_GMSK_GSM900_APC_DAC = 50;MIN_GMSK_DCS1800_APC_DAC = 50;MIN_GMSK_PCS1900_APC_DAC = 50;MAX_GMSK_GSM850_APC_DAC = 550;MAX_GMSK_GSM900

45、_APC_DAC = 550;MAX_GMSK_DCS1800_APC_DAC = 550;MAX_GMSK_PCS1900_APC_DAC = 550;MIN_EPSK_GSM850_APC_DAC = 200;MIN_EPSK_GSM900_APC_DAC = 200;MIN_EPSK_DCS1800_APC_DAC = 200;MIN_EPSK_PCS1900_APC_DAC = 200;MAX_EPSK_GSM850_APC_DAC = 700;MAX_EPSK_GSM900_APC_DAC = 700;MAX_EPSK_DCS1800_APC_DAC = 700;MAX_EPSK_P

46、CS1900_APC_DAC = 700; for FHC onlyFHC_UTS_GMSK_GSM850_MEASURE_SAMPLES = 30FHC_UTS_GMSK_GSM900_MEASURE_SAMPLES = 30FHC_UTS_GMSK_DCS1800_MEASURE_SAMPLES = 30FHC_UTS_GMSK_PCS1900_MEASURE_SAMPLES = 30;FHC_UTS_EPSK_GSM850_MEASURE_SAMPLES = 50;FHC_UTS_EPSK_GSM900_MEASURE_SAMPLES = 50;FHC_UTS_EPSK_DCS1800_

47、MEASURE_SAMPLES = 50;FHC_UTS_EPSK_PCS1900_MEASURE_SAMPLES = 50FHC_UTS_GMSK_MEASURE_COUNT = 1FHC_UTS_EPSK_MEASURE_COUNT = 1FHC_UTS_GSM850_GMSK_MATH_MODE = 1FHC_UTS_GSM900_GMSK_MATH_MODE = 1FHC_UTS_DCS1800_GMSK_MATH_MODE = 1FHC_UTS_PCS1900_GMSK_MATH_MODE = 1;FHC_UTS_GSM850_EPSK_MATH_MODE = 0;FHC_UTS_G

48、SM900_EPSK_MATH_MODE = 0;FHC_UTS_DCS1800_EPSK_MATH_MODE = 0;FHC_UTS_PCS1900_EPSK_MATH_MODE = 0;FHC_UTS_APC_DAC_MODE = 0FHC_UTS_GMSK_APC_DAC_MODE = 0;FHC_UTS_EPSK_APC_DAC_MODE = 0FHC_UTS_GSM850_GMSK_APC_LOG_SPACE_OFFSET=-60.54;FHC_UTS_GSM850_EPSK_APC_LOG_SPACE_OFFSET_HIGH=1036.13;FHC_UTS_GSM850_EPSK_

49、APC_LOG_SPACE_OFFSET=-376.04FHC_UTS_GSM900_GMSK_APC_LOG_SPACE_OFFSET=-60.54;FHC_UTS_GSM900_EPSK_APC_LOG_SPACE_OFFSET_HIGH=1036.13;FHC_UTS_GSM900_EPSK_APC_LOG_SPACE_OFFSET=-376.04FHC_UTS_DCS1800_GMSK_APC_LOG_SPACE_OFFSET=-74.48;FHC_UTS_DCS1800_EPSK_APC_LOG_SPACE_OFFSET_HIGH=-331.86;FHC_UTS_DCS1800_EP

50、SK_APC_LOG_SPACE_OFFSET=-429.16FHC_UTS_PCS1900_GMSK_APC_LOG_SPACE_OFFSET=-72.44;FHC_UTS_PCS1900_EPSK_APC_LOG_SPACE_OFFSET_HIGH=469.12;FHC_UTS_PCS1900_EPSK_APC_LOG_SPACE_OFFSET=-368.30ADC tableADC电池电量校准ADC_V1 = 3400最小电压ADC_V2 = 4200最大电压ADC_CHECK_VOLTAGE = 3600NORMAL_VOLTAGE = 3900校准时的电压CURRENT_LIMIT

51、= 3000电流限制值MAX_BATTERY_ADC_SLOPE = 5650电量斜率最大值MIN_BATTERY_ADC_SLOPE = 5250电量斜率最小值MAX_BATTERY_ADC_OFFSET = 1000000MIN_BATTERY_ADC_OFFSET = -1000000BATTERY_CHANNEL = 0CHARGER_CHANNEL = 1ADC_RESISTANCE = 0.4MAX_VOLTAGE_DIFFERENCE = 0.04MAX_CURRENT_DIFFERENCE = 0.04ADC_MEASUREMENT_COUNT = 1000以下是引用tanpe

52、ng_wh在2008-6-27 18:59:30的发言：校准设置文件以及校准check限制条件（*.CFG文件）：                 主要是对手机校准的时候起作用，使得校准按照此文件内的内容去执行，比如在哪个信道、哪个功率等级，哪种综测仪等等。最后在校准完成以后来重新check，如果一旦超出check限制条件就算此校准Fail。功率校准Fail，但是只是相差一点（与限制的范围相差一点），碰到这种情况可以把*.ini中相应频段相应功率等级对应的Vapc对应的ADC置增加一点就可以了。

53、校准设置文件以及校准check限制条件（*.CFG文件）：   主要是对手机校准的时候起作用，使得校准按照此文件内的内容去执行，比如在哪个信道、哪个功率等级，哪种综测仪等等。最后在校准完成以后来重新check，如果一旦超出check限制条件就算此校准Fail。功率校准Fail，但是只是相差一点（与限制的范围相差一点），碰到这种情况可以把*.ini中相应频段相应功率等级对应的Vapc对应的ADC置增加一点就可以了。br<p align=right><font color=red>+3 RD币</font></p>是调整VPC的值

54、，就是把ADC的值调大些，让对应的点的输出功率大些。知道什么是功率控制吧？校准文件介绍  利用ATE对手机进行射频和ADC校准需要用到如下一些文件：NVRAM Database；Flash的Nvram区用于存储手机的一些基带和射频参数，Nvram database相当于定义了这些参数存储的数据结构Setup.ini   例如：CROCODILE_8960_Setup _060914.iniCal.ini  例如：Crocodile_Cal_ 060914.iniCfg.cfg  例如：CROCODILE_CFG _

55、060914.cfgSetup.ini文件是系统设置文件，用于校准终测时对系统测试仪器设置和初始化，包括终测仪，电源的GPIP地址，串行通信口，其它相关校准文件的路径，终测时呼叫建立的信道设置，cell power功率设置，测试项目设置，校准设置，cable loss设置等。Cal.ini文件为手机校准之前的缺省参数，包括射频接收Path loss参数，AFC参数，发射power level DAC值和ramp profile参数，ADC参数，这些缺省参数在手机校准之前校准程序会先把它写到手机的NVRAM里面，然后在这些缺省参数的基础上进行校准。其中ramp profile参数是手机发射突发脉

56、冲的PvT参数，只是在校准的时候写到手机里面，程序不会对这些参数进行校准，这些参数在研发的时候会根据PA的类型预先调好。只要PA是一样的ramp profile参数就是一样的，不同类型的PA这些参数不一样。Cfg.cfg文件为校准的配置文件，内容包括综测仪GPIB地址和cable loss设置（只有用META校准的时候才用这些参数，用ATE校准的时候cable loss是在setup.ini文件读取），校准的频段和每个频段用来校准的信道设置，RX path loss的limit范围设置，AFC limit范围设置，发射各个功率等级的目标功率以及limit 范围设置，ADC的limit 范围设置

57、等。校准结果是Pass还是fail程序就是靠检测校准结果有没有落在cfg文件的limit设置范围内来判断的。4.1INI文件的介绍：；411射频功能组的复位；下面是setupINI文件中定义的项目；GSM900Sig=1；GSM1800Sig=1；GSM1900Sig=1；GSM900NSig=1；GSM1800NSig=1；GSM1900NSig=1；通常设置为1，指在对CMU200设置之前对设备进；412系统设置：；setupINI文件中定义的项目4.1 INI 文件的介绍：411射频功能组的复位下面是setup INI文件中定义的项目。GSM900 Sig = 1GSM1800 Sig

58、= 1GSM1900 Sig = 1GSM900 NSig = 1GSM1800 NSig = 1GSM1900 NSig = 1通常设置为1，指在对CMU200设置之前对设备进行复位，为0时不复位。412 系统设置：setup INI文件中定义的项目：External Reference Clock = 0 默认值为0，指使用CMU200输出的参考时钟，为1时使用外部参考时钟。CMU Base GPIB Address = 20CMU的GPIB地址的设置，要与软件对应。Instrument = "CMU200"使用的设备为CMU200Power Supply Addres

59、s = GPIB0:5:INSTR电源地址的设置使用Kei230x时，应为Power Supply Address = 5CMU RF Port = 2CMU200使用的射频端口设置Test Mode = 0设为0指需要手动对设备进行初始化，1指在综测时软件将自动对设备进行初始化，2指在校准时软件将自动对设备进行初始化，3指在校准和综测联合测试时软件将自动对设备进行初始化FDM database file = "c:Program FilesMTK_atedemoreportBPLGUInfoCustom" Database文件的存放路径，必须与手机软件对应Calibration file = "c:Program FilesMTK_atedemoMTKCAL_6205B.INI"校准初始默认值设置文件的路径Config file = "c:Program FilesMTK_atedemometa_6205B.CFG"关于校准的设置，如校准的信道，限制的最大、最小值Re