HSD9.7 产品规格书.doc

XXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXAPPROVAL SHEET承 认 书Customer客户名称Part NO.产品型号HSD9.7Product type产品内容Mode: Transmissive type .Normally white. TFT LCD ModuleLCD Module: Graphic1024RGB*768Dot-matrixRemarks备注栏APPROVAL FOR SEPCIFICATIONS ONLYAPPROVAL FOR SEPCIFICATIONS AND SAMPLESignature by Customer:客户确认签章Issued byChecked byApproved byPDQA深圳市XXXXX电话：86-0755-XXXXXX传真：86-0722- XXXXX地址：深圳XXXXXXXXXXXXXXXXXXXTABLE OF Contents 1. General Description.22. Features.23. Mechanical Specification.24. Mechanical Dimension.35. Maximum Ratings.46. Electrical Characteristics.47. Backlight Characteristic.58. Module Function Description.69. Electro-optical Characteristics.910. Reliability1211. Inspection Standards1312. Precautions For Using LCD Modules.1613. Factory.1714. Revision History.181. General DescriptionYX043CL-30-4-A is a 480RGB*272 dots matrix TFT LCD module. It has a TFT panel composed of 800 sources and 480gates. The LCM can be easily accessed by micro-controller. 2. Features Display ModeTransmissivea-TFTDisplay FormatGraphic 1024RGB*768Dot-matrixInput DataRGB interface Viewing DirectionFreeDriveHX8282，HX86953. Mechanical SpecificationItemSpecificationsUnitDimensional outline210.01MM*164.05MM*2.9MAXmmResolution1024RGB*768dotsLCD Active area 196.61(W)*147.46(H)mmPixel size0.198 (W)*0.198(H)mm4. Mechanical Dimension5. Maximum RatingsItemSymbolMinMaxUnitNoteSupply voltageV3.03.6VOperating temperatureTOPR-1060Storage temperatureTSTR-20706. Electrical CharacteristicsItemSymbolConditionMin.Typ.Max.UnitSupply voltageLogicVCC2.73.33.5VInput VoltageH levelTIH0.8*IOVCCIOVCCVL levelTIL-0.30.2* IOVCCStorage temperatureIDD/ICCVCC=3.3V;Temp=25/DCLK=33MHz8.0mA 7. Backlight CharacteristicItemSymbolMinTypicalMaxUnitLED module Forward voltageVLED18.619.219.8VLED module currentVLED120mAL/G Surface Luminance 1LS42004600Cd/m3LCM Surface brightness uniform 2LD80% 1Test condition is:(a) Center point on active area.(b)Best Contrast. 2Uniform measure condition:(1)Measure 9 point. Measure location show below;(2)Uniform=(Min. brightness /Max. brightness)*100%(3)Best Contrast.8. Module Function Description8.1Pin Descriptions1.Pin NO.SymbolDescription1GND Power ground2VDDPower for LED backlight (Anode)3VDDNo conection4VEDIDPower for LED backlight (Cathode)5NCNo conection6VED-SCLCommon Voltage7VES-SDADigital Power8D0N-LVDS differential data input(R0-R5,G0)9D0P+LVDS differential data input(R0-R5,G0)10GND Power ground11D1N-LVDS differential data input(G1-R5,B0-B1)12D1P+LVDS differential data input(G1-R5,B0-B1)13GNDPower ground14D2N-LVDS differential data input(B2-B5,HS,VS,DE)15D2P+LVDS differential data input(B2-B5,HS,VS,DE)16GNDPower ground17LVCN- LVDS differential clock input18LVCP+LVDS differential clock input 19GNDPower ground 20NCNo conection 21LED-A Power for LED backlight (Anode) 22LED-A Power for LED backlight (Anode) 23NCNo conection 24LED-K1Power for LED backlight (Catgode) 25LED-K2Power for LED backlight (Catgode) 26LED-K3Power for LED backlight (Catgode) 27LED-K4Power for LED backlight (Catgode) 28LED-K5Power for LED backlight (Catgode) 29LED-K6Power for LED backlight (Catgode) 30BIST8.2Timing characteristics.Read Timing CharacteristicsReset Timing Characteristics(VCC=1.83.3V.IOVCC=1.653.3V)ItemSymbolUnitMin. Typ.MaxReset low-level widthtRESms1Reset rise timetRESs109.Electro-optical CharacteristicsItemSymbolConditionsTempMin.Typ.Max.UnitNoteResponse TimeTR= =025TBDTBDmsecNOTE2TFTBDTBDViewing Angle Range=00(6”)=900(3”)=1800(12”)=2700(9”)NOTE3(25) CR10TBDTBDTBDTBDNOTE3The above “viewing angle” is the measuring position with the largest contrast ratio. Not for good image quality. Viewing direction for good image quality is 12 Oclock.For panel onlyElectro-Optical Characteristics Test Method .Note2.Definition of Optical Response Time: .Note3.Definition of Viewing Angleand:Note4.Definition of Contrast ratio (CR):10. Reliability10.1MtbfThe LCD module shall be designed to meet a minimum MTBF value of 50000 hours with normal10.2Test conditionNO.ITEMCONDITIONCRITERION1High Temperature Non-Operating Test80*240Hrs。No Defect Of Operational Function In Room Temperature Are Allowable。IDD of LCM in Pre-and Post-Test Should Follow Specification2Low Temperature Non-Operating Test-30*240Hrs3High Temperature/Humidity Non Operating Test60*90%RH*240Hrs4High Temperature Operating Test70*240Hrs5Low Temperature Operating Test-20*240Hrs6Thermal Shock Test-20(30Min) n70(30Min) *10CYCLESNotes:1. Judgments should be made after exposure in room temperature for two hours.2. The distill water is used for the high temperature/humidity test.3. The sample above is individually for every reliability tests condition.11.Inspection standards1.AQL(Acceptable Quality LevelAQL of major and minor defect.MAJOR DEFECTMINOR DEFECTAQL0.651.52. Basic conditions for inspectionThe LCM face to us, in normal environment, the lux is 1000200.(Darkrooms lux: 10050),About an angle of incidence 30,a distance of 30 cm with an angle of 45 degree to check the products without uncovering the film! (As shown below)3.Inspection item and criteria3.1 Visual inspection criterion in immobility3.1.1Glass defectNODefect itemCriteriaRemark1Dimension Unconformity(Major defect)By Engineering Drawing2Cracks(Major defect)1. Linear cracks panel【Reject】2. Nonlinear crack contrast by limited sample3Glass extrude the conductive area(minor defect)a: disregards and no influence assemblage.1) b1/3Pin width(non bonding area)【Accept】2)bonding area0.5mm【Accept】A: Length, b: Width4Pin-side ,conductive area damaged(minor defect)(a c: disregards)b1/3of effective length for bonding electrode【Accept】a: length, b: Width, c: Thickness 5Pin-side,non-conductive area damaged(minor defect)1)Damage area dont touch the ITO (Inclueling contraposition mark, except scribing mark)【Accept】2)CT bBM1/3of width【Accept】3)c=T b not touch the seal glue【Accept】4)a disregardsa: Length, b: Width c: Thickness6Non-pin-side damage(minor defect)cT1)b exceeds 1/3Bm【Reject】c=Tb not touch the seal glue【Reject】c: Thickness b: width of damage3.1.2LCD appearance defect(View area)NODefect itemCriteriaRemark1Fiber、glasscratch、polarizerscratch/folded(minor defect)SpecificationAllowablenote1:L: Length, W: Widthnote2: disregard if out of AAW0.03mmdisregard0.03mmW0.05mm;L3.0mm20.05mm0.1mm;L3.0mm02Polarizer bubble、concave and convex(minor defect)0.2mmdisregardnote1: =(L+W)/2,L:Length,W :Widthnote2:disregard if out of AA0.2mm0.3mm20.3mm0.5mm10.5mm03Black dots、dirty dots、impurities、eye winker(minor defect)0.15mmdisregardnote2:disregard if out of AA0.15mm0.25mm20.25mm0.3mm10.3mm5mm0.1mm0.25mm03.1.3FPCNODefect itemCriteriaRemark1Copper screen peel(minor defect)Copper screen peel 【Reject】2No release tape or peel No release tape or peel 【Reject】3Dirty dot and impurity of FPC for customer using side(minor defect)SpecificationAllowableNote1: Cannot have stride ITO impurities 0.25mm20.2503.1.4Black tape &Mara tapeNODefect itemCriteriaRemark1FPC or H/S black tape(minor defect)1. shift spec:1) glue to the polarize【Reject】2) IC bare 【Reject】2. left-and-right spec:1)exceed of FPC edge or H-S edge【Reject】 2) IC bare 【Reject】2No black tape(major defect)No black tape 【Reject】3Tape position mistake(minor defect)Not by engineering drawing4Mara tape defect(minor defect)Peel before pulling the protecting film【Reject】3.1.5Silicon and Taffy glueNODefect itemCriteriaRemark1Quantity of silicon(major defect)Uncover the ITO and circuit area【Reject】note: compared by engineering2Taffy glue(major defect)1.Uncover the reveal copper area【Reject】2.Cover layer 0.3mm(Min)3.0mm(Max) 【Reject】note: if customer has special requirement, refer to the technical document 3Depth of glue covering(major defect)Depth of glue covering overtop front Polarizer 【Reject】Except of the special requirement3.2Electrical criteriaNODefect itemCriteriaRemark1No display (major defect)No display【Reject】2Missing line (major defect)Missing line 【Reject】3Seg-com light and dark(major defect)Seg-com light and dark【Reject】ND filter 2% test4No display in immobility(major defect)No display in immobility【Reject】5Flicker of Pattern(major defect)Flicker of Pattern【Reject】6Mura(major defect)ND filter 2%test7Over current (major defect)Over current 【Reject】8Voltage out of specification(major defect)Voltage out of specification【Reject】9Pattern blur, error code(major defect)Pattern blur, error code【Reject】10Dark light, Flicker(major defect)Dark light, Flicker【Reject】11Black/white dots、Dirty dots、eye winker(major defect)SpecificationAllowableNote1:disregard if out of AA 0.15mmdisregard0.15mm0.25mm20.25mm0.3mm10.3mm012Fiber、glass crutch、Polarizer scratch/folded(major defect)W0.03mmdisregardNote1:L: Length, W: WidthNote2: disregard if out of AA0.03mmW0.0.05mmL3.0mm20.05mm0.1mm;L3.0mm012.Precautions for using LCD modules. 12.1 Safety(1)Do mot swallow any liquid crystal ,even if there is no proof that liquid crystal is poisonous.(2)If the LCD panel breaks, be careful not to get liquid crystal to touch your skin.(3)If skin is exposed to liquid crystal, wash the area thoroughly with alcohol or soap.12.2Srorang Conditions(4)Store the panel or module in a dark place where the temperature is 235and the humidity is below 4520%RH.(5)Store in anti-static electricity container.(6)Store in clean environment, free