锂离子电池专业英语

1、文档编码 : CS1V2T9Y1S5 HV7I7U2S2Z7 ZH6Y4Q1C6T3锂离子电池常用专业英语（一）序号A 首字母英文中文机电部1 aging 老化2 B battery charger 充电器3 C black-fleck 黑斑4 cap 盖板5 D capacity density 能量密度6 capacity grading 分容7 cathode tab welding 极耳超焊8 cell 电芯9 chargecapacity retention 荷电（容量）保持10 checking code 检码11 concave spot 凹点12 constant curren

2、t charge 恒流充电13 constant current discharge 恒流放电14 constant voltage charge 恒压充电15 corrective measures 订正措施16 crack 裂纹17 cut-off voltage 终止电压18 cycle life 循环寿命19 dark trace 暗痕20 E degrade 降级21 dent 凹痕22 discharge depth 放电深度23 distortion 变形24 drape 打折25 Electrical and MechanicalServices Department 26 F

3、 electrolyte 电解,电解液27 empaistic 压纹28 end-off voltage 放电截止电压29 environmentally friendly 对环境友好30 equipment first inspection 设备首检31 erode 腐蚀32 explosion-proof line 防爆线33 first inspection 首检34 I formation 化成35 fracture 断裂36 inspection 检验37 J insulate 绝缘38 internal resistance 内阻39 jellyroll 卷芯40 joint 接缝

4、,结合点41 L laser deflecting 偏光42 laser reticle 激光刻线43 laser welding-flatwise weld 激光焊接 -平焊laser welding-standing weld 激光焊接 -立焊44 leakage 漏液45 leak-checking 测漏46 leaving out of welding 漏焊47 limited charge voltage 充电限制电压48 local action 自放电49 M margin turnly 翘边50 measuring the dimension of cells 电芯卡尺寸51

5、meet requirement 达到要求52 memory effects 记忆效应53 N nick 划痕54 nominal voltage 标称电压55 notice-board confirmation 看板确认56 nugget 硬块57 O obverse 正面58 open circuit voltage 开路电压59 over charge 过充60 over discharge 过放61 over the thickness 超厚62 P particle 颗粒63 PE membrane PE 膜64 pit 坑点65 placing cells into the box

6、 电芯装盒66 point inspection 点检67 preventive measures 预防措施68 pricking the tapes 扎孔69 process inspection 制程检验70 put the battery piled up 将电芯叠放在一起71 Q qualified products 合格品72 quality assurance 质量保证73 quality control 质量把握74 quality improvement 质量改进75 quality match 品质配对76 quality planning 质量策划77 R rated ca

7、pacity 额定容量78 recharge 再充电79 refitting the can of cell 电芯壳口整形80 requirment 要求81 reverse 背面,反面82 rework 返工83 ringing cells into pyrocondensation films 套热缩膜84 S safety vent 安全阀85 sand aperture 砂眼86 scar 疤痕87 secondary battery 二次电池88 select appearance 选外观sharp-set 批锋89 short circuit checking 测短路90 smud

8、giness 污物91 spot welding by laser 激光点焊92 spot welding place 点焊位置93 spraying the code 喷码94 spur 毛刺95 sticking the PVC cover boards 贴面垫96 storing 陈化97 storing with high voltage 高压储存98 T tabs deflection 极耳歪斜99 tabs excursion 极耳错位100 technics requiment 工艺要求101 U ultrasonic welding 超声波焊接102 ultrasonic we

9、lding strength 超焊强度103 unqualified products 不合格品104 W wave 波浪105 working procedure 工序（二）盖板 cover board 底板 solepiece 钢珠 steel ball 压钢珠 press steel ball 防爆阀 valve preventing explosion 大电流 倍率 放电 discharge in high rate current 标称电压 Normal voltage 标称容量 normal capacity 放电容量 discharge capacity 充电上限电压 limit

10、ed voltage in charge 放电下限电压 terminating voltage in discharge 恒流充电 constant current charge 恒压充电 constant voltage charge 恒流放电 constant current discharge 放电曲线 discharge curve 充电曲线 charge curve 放电平台 discharge voltage plateau 容量衰减 capacity attenuation 起始容量 initial discharge capacity 流水线 pipelining 传送带 ca

11、rrying tape 焊极耳 welding the current collector 卷绕 wind 叠片 layer 贴胶带 stick tape 点焊 spot welding 超声焊 ultrasonic welding 三元素 Nickle-Cobalt-Manganese Lithium Oxide three elements materials 钴酸锂 Cobalt Lithium Oxide 锰酸锂 Manganese Lithium Oxide 石墨 graphite 烘箱 oven 真空烘箱 vacuum oven 搅拌机 mixing device vacuum m

12、ixing device 涂布机 coating equipment 裁纸刀 paper knife ,cutting knife 分条机 equipment for cutting big piece to much pieces 辊压机 roll press equipment 电阻点焊机 spot welding machine 超声点焊机 ultrasonic spot welding machine 卷绕机 winder 自动叠片机 auto laminating machine 激光焊机 laser welding machine 注液机 infusing machine 真空注液

13、机 vacuum infusion machine 预充柜 pre-charge equipment 化成柜 formation systems 分容柜 grading systems 测试柜 testing systems 内阻仪 battery inner resistance tester 万用表 multimeter 转盘式真空封口机 turntable type vacuum sealing machine 自动冲膜机 automatic aluminum membrane shaper 锂离子电池设计专业英语Capacity 容量Battery Thickness 电池厚度Batt

14、ery width 电池宽度Battery length 电池高度Impedance 内阻Can thickness 壳体厚度Can wall thickness 壳体壁厚Can bottom thikness 壳体底部厚度Can lid thickness 壳体盖板厚度PP film thickness PP 胶厚度Ni AL tab thickness Ni （Al ）极耳厚度Battery width 电池宽度Can width margin 电池宽度留边Can length 壳体长度Can cross area 壳体体积Winding pin width 卷针宽度Can Side re

15、sidue 壳边残余Naked battery thickness 裸漏电池厚度Naked battery width 裸漏电池宽度Naked battery length 裸漏电池高度Cathode formulation 阴极含量Cathode material specific capacity 阴极克比容量Cathode 阴极装填Cathode area density 阴极面密度Cathode bulk density 阴极体积密度Cathode weight 阴极重量Cathode thickness 阴极厚度Cathode elongation rate 延长率Cathode actual length 阴极实际长度Cathode design le