日立存储调试详细步骤-HUS130

1、硬件连接方法：两根sas线 机头A控制器0 口连扩展柜A控IN 口机头B控0 口连扩展柜B控IN 口光纤线连接AB控上方两个光口即可（AB控一共4根线）开机方法找小棍长按MAN-SW按钮三秒 等待5分钟待前面灯全变成绿色第一步：在笔记本中安装Hitachi Storage Navigator Modular 2软件在印有 Hitachi Storage Navigator Modular 2 for windows 光盘上可以找到Windows_GUIHSNM2-2170-W-GUI-P01.exe 并执行 安装过程中要求输入IP地址 可以直接下一步 第二步:连接存储连接存储 将网线直连到存储

2、第一个控制器最右侧的网口也就是印有网络图标的网口（非印有小扳手的网口）设置本机IP为192.168.0.*网段IP ping 6是否可以通打开 IE 地址栏输入： HYPERLINK :23015/StorageNavigatorModular/Login :23015/StorageNavigatorModular/Login 账号：system密码：manager进入后会有一个向导Newt | | Cancel Help )HSNM2 - Add Array WizardReview the steps below to connect to your array.This wizard

3、will take you through the process of configuring the navigator to manage arrays.Introduction Search Array Add Array Finish1.HITACHI1. Introductn2. Search Array 3. Add Array 4. Finish第二页输入控制器IP地址即可：Controller 0： 6 （输入一个就可以）Required fieldSNM2 -Add Array WizardEnter the information for array searching.

4、。Secure Port。Non-secure and Secure Ports(Secure port is searched at first.)ControllZilEnter the IP Address or array name. Array name cant be more than 255 characters.Search for IPv6 Addresses automaticallyUsing Ports: Non-secure PortSearch MethodRange of 回 Range of IPv4、IP Addresses:Address:From|q；

5、IP Address or Array Name:Controller 0: |192.168.O.16HITACHI1. Introduction 2. Search Array * 3. Add Array 4. Finish直接下一步第三步：激活LICENSE点击新添加的存储进入存储管理页面nArr% NameStatusGroupModelSerial No.Capacity of All VOLRaw Capacity of All DrivesMonitor ErrorIP AdiContnin|jHUSL30_92210592NormalHUS1309221059214.6TB1

6、8.8TBYes192.16右下角会有蓝色Install license点击进入插入 纸张上印有HUS 130字样的license光盘（有两张自己试试哪一张好使） 点击Key File后面的浏览寻 Fi|ei |Input the Key File Name找到光盘中的激活文件（就一个）点击OK激活完成第四步:做RAID先做个热备盘在左侧Settings下面有 Drive Settings下面Spare Drives里面 Add SpareDrive把最后一块盘做成热背叛再做RAID 点击左侧GROUPS-volumes右边会有RAID GROUPS进入下方会有CREATERG按钮进入第一个空

7、是组名（随便）RAID 模式（RAID5）磁盘配置方式（6D+1P）就是六个数据盘加一个校验盘下面选择手动制作MANUAL SELECTION里面选硬盘 你选的6D+1P就选7块盘 一共36块硬盘用了一块做热备还剩35块盘每个RAID5用7块盘那么我们就做5个RAID5第五步： 制作 volume为了测试我们先分20个VOLUME每个100G 在VOLUMES选项卡下点CREATE VOL进入RAID GROUP是选在哪个RAID组上做VOL:是序号CAPACITY是大小（测试用就每个先分100GB）点OK下一页让配置MAPPING不用管 可以点create more vol按钮继续建立VOL

8、UME 为了测试用建立20个VOLUME我们就将这20个volume平均建立在5个RAID组上 也有快速建立的方式在第一页有个建立VOLUME向导你可以尝试下Create Volume and Mappfng书Create volume and mapping easily.第一个是多大第二个是分几个 Create many volumes : Vo|ume Capadt-r- :10GB Number of Volumes : i第六步：建立MAPPING左侧GROUPS下面有HOST GROUPS里面有HOST GROUP SECURITY选项卡能看到八个端口全部选择上点击change h

9、ost group security按钮选中YES点OK这样就能显示出来连接进来的光线设备的WWN号点击HOSTGROUPS选项卡随便点一个HOSTGROUP的蓝字进入Host GroupsHost Group Security WWNsRows/Page: 25 | 叵) Pagel of 1 K)Host GroupPort PlatformMiddleware莅加口印魅EGL0AWin demsnot specifiedk |001JMrver2OAWindowsnot specified0k |o 02 sserver30AWin demsnot specified0k |0OQsse

10、rverlOBWindowsnot specified0k |0Qlsserver2OBWindovsnot specified0k |o 02 sserver3OBWindowsnot specified0k |OOQ sserver 1OCWin demsnot specified0k |o 01 sserve r2OCWindowsnot specified0k |002sserver3OCWindowsnot specified0k |0OQsserverlODWindowsnot specified点击右上角的EDIT HOST GROUP选择所有的PORT并把FORCED SET

11、TO ALL SELECTED PORTS前面的勾打上先将WWNS里面扫到的所有设备添加进来Volumes OptionsCheck WWN or enter new port name form and click Add v/hen assign WWN to host group.Check selected WWN and push Remove when disassign WWN from host group.佥 Select From List Enter WWNs ManuallyDetected WWNsSelected WWNsRows/Page: 25 | 叵)(HD

12、Pa9eof 0 屁Rows/Page: 251.1-1 .1 匝.1 Page L of 1 叵1 CEJNicknamePort NamePortNicknamePort NamePortNo ObjectB10000000C9FA0&47OA| Add Settings Port Settings FC SettingsrFC PortsFC PortTransfer RateTopologyLinkStatusSettingCurrent8Gbps8GbpsPoint-to-PointLinkUp(F_Port Connected)：iBAuto8GbpsPoint-to-PointL

13、inkUp(F_Port Connected)：iCAuto8GbpsPoint-to-PointLinkUp(F_Port Connected)：iDAuto8GbpsPoint-to-PointLinkUp(F_Port Connected)ri.AAuto8GbpsPoint-to-PointLinkUp(F_Port Connected)Auto8GbpsPoint-to-PointLinkUp(F_Port Connected)1.CAutoSGbpsPoint-to-PointLinkUp(F_Part Connected)Auto8GbpsPoint-to-PointLinlkU

14、p(F_PQrt Connected)点击右上角按钮EDIT FC PORT进入将 TOPOLOGY 项改成 POINT-TO-POINT 按 OKEdit FC Port - Port OArProperties of FC PortEnter the information to edit the FC Port.* Port Address:jaOODEF* Transfer Rate:SGbps * TopologyePa int-ta-Point * Required field依次将8个端口全部改完8 GbpsKGbpsPoint-to-PointLinkUp(F_Port Connected)oeAutoGbpsPoint-to-PointLinkUp(F_Port Connected):cAutoSGbpsPoint-to-PointLinkUp(F_Port Connected)AutoSGbpsPoint-to-PointLinkUp(F_Port Connected)LAAuto8GbpsPoint-to-PointLinkUp(F_Port Connected)LBAuto8GbpsPoint-to-PointLinkUp(F_Port Connected)Auto8GbpsPoint-to-Poi