加工中心全部的报警说明

1、FANUC警报讯息说明Page:1/52007/2/12项次警报讯息说 明处理方法11000 DOOR NOT CLOSE CAN NOT START安全门未关不能启动关闭前门21001 CHECK POT UP LS&SOL刀套木在水平位置检查刀套上开关及电磁阀31002 Z AXIS NOT IN 2 POSITIONZ轴未在换刀点位置上重新校验Z轴换刀高度41003 Z AXIS CANCELLEDZ轴取消检查Z轴取消情况51004 ATC NOT READYATC未准备完成a.检查主轴是否在夹刀状态及 开关是否正常b.检查刀臂是否在原点位置及 原点开关是否正常61005 ARM RUN

2、 OVER TIME刀臂换刀超过时间检查热继电器是否跳脱71006 TOOL NO. NOT SETTING刀具号码不在数据表上81007 ATC LS. FAILURE刀臂上开关故障91008 CHECK POT DOWN LS&SOL检查刀套下开关及电磁阀检查刀套下开关及电磁阀二101009 OIL COOLER FAILURE主轴油冷警报检查油面图度及压力开关111010 CHECK TOOL UNCLAMP LS检查主轴松刀开关检查主轴松刀开关121011 CHECK TOOL CLAMP LS检查主轴夹刀开关检查主轴夹刀开关131012 CHECK ARM BRAKE SENSOR

3、1 &MS.OL检查刀臂煞车点开关检查刀臂煞车点开关141013 4TH AXIS CLAMPED第四轴在夹的状态151014 CHECK ARM U/C SENSOR 2 &MS.OL刀臂未在原点位置161015 LUBE ALARM CANNOT CYCLE START润滑油油量太低不能程序启动填加润滑油171016 AIR ALARM CANNOT CYCLE START气压压力太低不能程序启动检查空气压力（必须68kg/cm2）181017 TOOL NO. C0刀具号码大于刀库最大号码191018 MAG. NOT ORIENT刀库未定位检查刀库开关刀库重整（程序暂停+RESET）2

4、01019 NO. OF PARTS REACHED211020 ARM SENOR K7&Q7 FAULT刀臂过载跳脱检查过载彳护器 Q7是否跳脱n221021 ATC COUNTER ERROR刀库计数与检测信号不对检查刀库计数检测开关刀库重整（程序暂停+RESET）231022 SPINDLE ALARM主轴警报241023 EMERGENCY STOP紧急停止252024 LOW LEVEL WATER切削液低水位a.检查水箱之水位是否过低 b.检查水位开关是否故障262025 TOOL BROKEN DETECT刀具破损检知271026 BFD71可程序喷嘴角度超过设定值281027

5、 5AXIS CLAMP第五轴在夹的状态291028 H/L GEAR POSITION ERROR高低档位置错误检查高低档开关是否正常301029 GEAR CHANGE OVER 10SEC变速箱高低档切换间操过10秒311030 GEAR OIL PRESSURE LOW变速箱油量低a.检查变速箱的油量b.检查压力开关是否故障321031 MAG RUN OVER TIME刀库运转超过时间331032 ARM IN TEST MODE刀臂在测试模式将K0.3设为0341033 ATLM FAULT自动刀长量测警报352034 FRONT DOOR OPENCE规格前门未关闭关闭前门362

6、035 SIDE DOOR OPENCE规格侧门未关闭关闭侧门371036 DEVICE NOT CLAMP治具没有夹381037 AXIS NOT HOME OK轴没有归原点将轴归原点392038 MIST LOW FLOAT低水位401039 HYDRAULIC FAULT油压单元散障412040 FILTER DIRTYC.T.S滤网脏清除滤网或更换滤网422041 C.T.S. LOW PRESSUREC.T.S压力低检查管路是否阻塞431042 ARM NOT IN U/C POS刀臂没有在原点位置441043 ARM NOT IN C POS刀臂没有在扣刀位置451044 LUBE

7、 LOW PRESSURE润滑油压力低461045 DOOR NOT CLOSE CANNOT CYCLE START安全门未关闭不能程序启动472046 PLS PRESS DOOR CLOSE AGAIN482048 PLS DOOR CLOSE USE HAND2007/2/12MITSUBISHI刀臂式机器警报讯息Page:2/5地址警报讯息中文说明排除方法F0000:F0 ATLM FAULT自动刀具量测故障F0001F1 3-AXES NOT HOME三轴未归原点执行手动原点复归F0002F2 DOOR NOT CLOSE防屑门未关闭将防屑门关好检查前门开关是否故障F0003F3

8、ATC NOT READYATC未准备完成检查刀臂是否在原点位置及主轴在夹刀状态(X6为1)检查刀臂近接开关及夹刀检知开关F0004F4 CL/UCL SW FAULT松夹刀检知开关同时动作检查夹刀/松刀检知开关F0005:F5 POCKET SW FAULT刀套上下检知开关故障检查套上/下检知开关F0006F6 T SEARCH NOT EXISTT指令刀号无在刀具登录中检查程序T指令刀号是否在刀具登录之中F0007F7 MAG. COUNTER ERR刀库计数检测错误重新将刀库重整检查刀库计数/检测检知开关F0008F8 ARM IN TEST MODE刀臂在测试模式关闭刀臂测试模式参数

9、#6403.0F0009:F9 SPINDLE OVER LOAD主轴过载F0010F10 SPINDLE ALARM主轴警报检查警示画面之显示状态，并核对操作手册或通知 维修人员F0011F11 MAG. NOT ORIENT刀库没有定位使用手动刀库正转/反转，旋转刀库 检查刀库定位检知开关F0012F12 4TH AXIS CLAMPED第四轴在夹的状态使用M41指令释放第四轴 检查第四轴夹/松检知开关F0013F13 BATTERY LOW电池电压低更换NC内的电池F0014F14 AIR PRESSERE LOW风压压力低检查风压来源是否足够 检查风压检知开关F0015F15 5-AX

10、IS CLAMP第五轴在夹的状态使用M51指令释放第四轴 检查第五轴夹/松检知开关F0016F16 LUBE AL. NOT START润滑油警报，不可程序启动检查润滑油之油量是否足够 检查润滑油之油量检知开关F0017F17 AIR AL. NOT START风压压力低，不可程序启动检查风压来源是否足够 检查风压检知开关F0018F18 TOOL NO.MAX.没有刀号所指定的刀号必须于 24之内F0019F19 NOZZLE POS. ERR可程序喷嘴原点位置错误检查原点检知开关是否不良F0020F20 Z-AXIS CANCELEDZ轴锁定按Z轴锁定按键，取消Z轴锁定F0021F21 P

11、ARTS REACHF0022F22 H/L GEAR POS. ERR变速箱高低档开关异常检查档位检知开关F0023F23 MAG OVER TIME刀库过时间F0024F24 OIL COOLER FAULT主轴油冷警报检查油冷却机是否异常F0025:F25 GEAR CH OVER 10S变速箱高低档切换超过 10秒检查高低档控制回路F0026F26 TOOL LIFE OVER刀具超过寿命更换刀片，并将开刀具寿命计次(时)归零F0027F27 ARM. OVER TIME刀臂过时间检查刀臂马达过载保护是否跳脱(Q7)及相关回路F0028F28 ARM SW. FAULT刀臂开关故障检查

12、刀臂马达过载保护是否跳脱(Q7)及相关回路检查刀臂检知开关是否不良F0029F29 DEVICE NOT CLAMP治具未夹检查夹治具检知开关是否不良F0030F30 GEAR OIL LOW PRESSURI莪速箱油量压力低检查变速箱油机是否异常F0031F31 FILTER DIRTY滤网脏清洗滤网F0032F32 C.T.S. LOW PRESSURE中心喷水压力低F0033F33 MAG. NO1 HAVE TOOLF0034F34 MAG. NO2 HAVE TOOLF0035F35 R-UNIT OVERHEAT泄放电阻过热短接 CF32-B11 与 CF32-COMF0036F3

13、6 LUBE LOW PRESSURE润滑油压力低检查润滑油之压力检知开关是否异常F0037:F37 4,5 AXIS NOT HOME第四五轴未归原点执行手动原点复归F0038F38 SPINDLE OVERHEAT主轴过热6405BIT0设1可解除F0039【F39 HYDRAULIC FAULT油压单元压力低检查油压单元是否异常F00402007/2/12FANUC 0i-TC 车床警报讯息说明Page：3/5地址警报名称原因A12.01120尾座心轴侦测开关1120 DETECTION SW. FOR TAILSTOCK SP.尾座后退的档块（166）不在正确位置上 尾座心轴前进与后退

14、的近接开关同时动作 检查与修理近接开关A12.11121主轴锁定侦测开关1121 DETECTION SW. FOR SPINDLE LOCK主轴固定与非固定的微动开关同时开启 检查与修理近接开关A12.21122门侦测开关1122 DETECTION SW. FOR DOOR门开与关闭的微动开关同时动作 检查与修理微动开关A12.31123尾座前进/后退开关1123 DETECTION SW. FOR TAILSTOCK F/R尾座轴前进端与后退端的近接开关同时开启 检查与修理近接开关A12.41124主轴侦测开关1124 DETECTION SW. FOR SP. MISSON任二个主轴高

15、速端，低速端与空档端同时开启 检查与修理微动开关A12.51125夹头侦测开关1125 DETECTION SW. FOR CHUCK夹头开启与关闭的完成确认开关同时打开检查与修理完成确认开关（微动，近接与压力开关）A12.61126防偏摆器开启/关闭侦测开关1126 DETECT SW. FOR STEADY REST O/C防偏摆器开启/关闭完成确认开关同时打开检查与修理完成确认开关（微动，近接与压力开关）A12.71127防偏摆器前进/后退侦测开关1127 DETECT SW. FOR STEADY REST F/R防偏摆器前进/后退的微动开关同时开启 检查与修理微动开关A13.0113

16、0 DETECT SW. FOR PARTS CATCHERA13.11131尾座开启/关闭侦测开关尾座夹紧与松开的完成确认开关同时打开检查与修理完成确认开关（微动，近接与压力开关）A13.21132 MELDAS SERVO TURRET ALARMA13.3A13.41134 MISSING PROGRAM NEED M5 COMMAND1135 DOOR SAFETY LOOP FAILA13.5A13.6A13.7A14.0A14.1A14.21142 M,S,T,B 讯号未完成1142 M,S,T,B SGNL. ARE NOT COMPLETED在执行M,S,T,B指令时即使时间超

17、过PMC定时器所设定的2倍时间仍未输出完成讯号检查M,S,T,B指令与其动作A14.31143主轴条件与以前相同1143 SP. COND. TO BE SAME AS BEFORE在程序停止的主轴状况，与在程序停止清除之后压下循环 开始键的主轴状况，事不一样的让主轴状况与程序停止的状况一样1144夹头条件与以前相同1144 CHUCK COND. TO BE SAME AS BEFORE在程序停止的夹头状况，与在程序停止清除之后压下循环 开始键的夹头状况，事不一样的让夹头状况与程序停止的状况一样A14.4A14.51145尾座心轴过行程1145 TAILSTOCK SP. NOT IN PO

18、SITION尾座的前进（165）,后退（166）近接开关都未动作夹头的工件长度不一木或工件未夹住，因此再尾座前进时，尾座会在前进末端开关确认后继续前进夹住适当的工件与前进尾座心轴，调整心轴与前进开关1146尾座心轴前进1146 PLS FORWARD THE TAILSTOCK SP.尾座心轴未前进时，主轴启动的方向 前进尾座心轴与主轴启动A14.61147关闭安全门1147 CLOSE THE SAFETY DOOR再丰轴游转成记个7槿式的 白 动搦作中门打开A14.71二IS干山川I干，孚!-匕1口。兵工乜口 J 口以口禾|卜丁, I JJ始门锁定有效2007/2/12Page:4/5FA

19、NUC 0i-TC车床警报讯息说明警报说明：地址警报名称原因A15.01150让门锁定开关有效1150 SELECT DOOR ILK.SW TO EFFECT再压下记忆模式的循环开始键时，门锁定无效使门锁定有效A15.11151关闭安全门1151 DOOR NOT CLOSE CAN NOT START再记忆模式中压下循环开始键时，门打开在讯息或 MDI模式下压下循环开始键时，使锁定无效时，门打开 将门关起来1152将齿轮改变为高速或低速1152 CHANGE THE GEAR TO HIGH OR LOW在主轴未变速时，主轴已转动 将主轴转到高速或低速A15.2A15.31153夹头夹紧1

20、153 CHUCK NOT TIGHTEN CAN NOT START再夹头松开时压下循环开始键 夹头夹紧A15.41154夹紧夹头1154 TIGHTEN THE CHUCK在夹头松开时压下主轴开始键 夹头夹紧A15.51155夹紧夹头1155 TIGHTEN THE CHUCK在主轴旋转时夹头松开 锁紧卡盘A15.61156夹头过行程1156 ODD OR EVEN ERROR工作件的直径不一样或是工作件未夹紧 夹紧适当的工件A15.71157 T讯号超过1157 T-SIGNAL OVER ALARM指示非可使用的模具号码 修改程序A16.0A16.11161 M16,M17,M18 指

21、令 T 讯号1161 M16,M17,M18 MISS T-COMMAND没有T指令,M16（刀具随机选择）,M17（刃物台正车）,M18（刃物台反转）指令T码A16.21162 SERVO TURRET ALARM驱动器显示92 ; 电池线位插好A16.31163 T00 COMMAND FAULTK13.1=1MR-J2-100D上的CN1B线24V1未与其它24V1相接，所以 没有24V,使得X9.4&X9.7都无信号.A16.41164 B讯号值过大1164 B CODE=360000指令B指令码超过3600范围 修改程序A16.51165回到尾座销位置1165 RETURN THE

22、PIN OF TAILSTOCK再尾座销超出时压下程序开始键 移回尾座销位置A16.6A16.7A17.51175 PRESS PROG. EDIT MODE RESET AGAINA17.61176 X,Z AXIS REFERENCE ONA18.21182在主轴运转时 M11无效1182 M11 INEFFEC WHEN SP. RUNNING在主轴旋转时下达指令M11（尾座撤回）停止主轴与下达指令M11A18.31183在齿轮空档时 M19.B无效1183 M19 INEFEC WHEN GEAR NEUTRAL在主轴的齿轮位于空档位置时下达指令M19.B（心轴停于固定位置） 从高速到

23、低速转动心轴下达指令M19.BA18.41184在主轴运转时 M24无效1184 M24 INEFEC WHEN SP. RUNNING在主轴旋转时下达指令M24（门开启）停止主轴与下达指令M24A18.71187在主轴运转时 M69无效1187 M69 INEFFEC WHEN SP. RUNING在主轴旋转时下达指令M69（夹头才开）停止主轴与下达指令 M69A19.21192 B SIGNAL INEFFECTIVEA19.31193 M73 INEF. WHEN REST REVERSE2007/2/12FANUC 0i-TC 车床警报讯息说明Page：5/5警报说明：地址警报名称原因

24、A19.51195 TAIL. SP. PRESSURE ALARMA19.61196 BAR FEEDER UNIT FAILS1197 M讯号重复指令再同一区块程序指令时，不可指定多重M机能1A19.71197 M-SIGNAL IS REPETITION COMMAND1200主油压马达过热检查主油压马达是否过热A20.01200 HYD. MOTOR THERMAL DEFFECTA20.21202 WATER COOLER FAILS1203切削水马达过热检查切削水马达是否过热A20.31203 COOLANT MOTOR THERMAL DEFECT1204主气压故障1204 LO

25、W AIR PRESSURE FAILS主气压降低设定气压标准值A20.41205主油压故障1205 MAIN HYDRAULIC FAILS主油压降低解决油压降低的原因A20.5A20.6A20.72210铁屑输送机马达过热检查铁屑输送机马达是否过热A21.02210 CHIP-CONV. MOTOR THERMAL DEFECT2211床卸润滑油液位太低2211 LEVEL OF BED LUB. OIL IS TOOL LOW床卸润滑油太少 添加床面润滑油A21.1A21.22214紧急开关被压下2214 EMERGENCY BUTTON IS PRESSED紧急开关被压下将开关钮往右旋

26、转在放开A21.42215备用电池的电压过低备用电池的电压过低，在开启电源后更换电池A21.52215 VOLTAGE OF THE BACK UP BATTERY IS TOO注意:如果未打开电源之前拿出电池，内部数据会被删除 1LOW2216机械运转失效，再次压下机器运转准备键压下机器运车隹备键，如果在压下机器运转准备键后仍然A21.62216 MACHINE READY FAILS. PRESS POWER ON发生同样的警示，BUTTON AGAINA21.72217测量失败侦测到测量器发生问题2217 MEASUREMENT FAILS2220工作夹紧检查失败2220 WORK CL

27、AMP CHECK FAILS工件夹头的设定不足，充分地设定工件到夹头，或调整底 座确认压力开关A22.0A22.12221工具寿命有限2221 TOOL LIFE IS LIMIT侦测刀具寿命更换新的刀具A22.21222 PMM TURRET CLAMPA22.31223 PMM TOOL NOT SERACHA22.41224 PMM TURRET ALARM2230机能指令转换失效再次打开电源并压下机器准备键A23.02230 FUNCTION COMMAND TRANSATC. FAILSP3003#3=0,K0.4=1,D0=11（MELDAS TURRET 车床）FANUC LH

28、警幸艮息明2008/01/17项次警幸艮a息明虑理方法11000 DOOR NOT CLOSE CAN NOT START安全力未信司不能敬勤worn231002 ZYX AXIS NOT IN 2 POSITIONZYX事由未在换刀黑占位置上重新校瞬ZYX事由换刀位置41003 Z AXIS CANCELLEDZ事由取消横查Z轴取消情况51004 ATC NOT READYATC未举借完成a.B查主轴是否在夹刀状熊及 信司是否正常b.检查刀臂是否在原黑占位置及原 黑占信司是否正常61005 ARM RUN OVER TIME刀臂换刀超谩日寺检查熟畿重器是否跳脱71006 LUBE LOW P

29、RESSURE润滑油屋力低81007 ATC LS. FAILURE刀臂上有故障91008 HYDRAULIC FAULT油屋军元故障101009 OIL COOLER FAILURE主轴油冷警幸艮检查油面高度及屋力信司111010 CHECK TOOL UNCLAMP LS检查主轴髭刀信封检查主轴髭刀信封121011 CHECK TOOL CLAMP LS检查主轴夹刀信司检查主轴夹刀信司131012 CHECK ARM BRAKE SENSOR 1 &MS.OL检查刀臂煞事黑“0身检查刀臂煞事黑“0身14151014 CHECK ARM U/C SENSOR 2 &MS.OL刀臂未在原黑占位

30、置161015 LUBE ALARM CANNOT CYCLE START润滑油油量太低不能程式改勤填加润滑油171016 AIR ALARM CANNOT CYCLE START氟屋屋力太低不能程式改勤检查空HM力（必68kg/cm2）181017 TOOL NO. C0刀具虢礁大於刀摩最大虢礁修正刀虢191018 TOOL NO.=0刀具虢礁=0修正刀虢201019 NO. OF PARTS REACHED211020 ARM SENOR K7&Q7 FAULT刀臂谩戴跳脱检查谩载保器Q7是否跳脱222021LUBE LOW PRESSURE托屋式润滑油屋力低231022 SPINDLE

31、ALARM主轴警幸艮241023 EMERGENCY STOP聚急停止252024 LOW LEVEL WATER切削液低水位a.检查水箱之水位是否谩低 b.检查水位信司是否故障262025 TOOL BROKEN DETECT刀具破损检知271026 HI/LOW WINDING ERRORSPINDLE HIGH/LOW ERROR检查H/L接斶器是否正常281027 5AXIS CLAMP第五触在爽的状魅291028 SPINDLE NO.=ARM NO.D0=D1修正D0和D1之值301029 SPINDLE TOOL NO.=0D0=0修正D0之值311030 GEAR OIL PR

32、ESSURE LOW建速箱油量低a.检查燮速箱的油量b.检查屋力信司是否故障321031 MAG RUN OVER TIME刀超遇日寺331032 ARM IN TEST MODE刀臂在模式 K0.30341033 ATLM FAULT自勤刀!量测警幸艮352034 FRONT DOOR OPENCE规格前力未信司朗部!前力362035 SIDE DOOR OPENCE规格俱肝号未信司朗371036 DEVICE NOT CLAMP治具没有爽381037 AXIS NOT HOME OK触没有色帚原黑占符事蝇帚原黑占392038 MIST LOW FLOAT低水位401040 B CORDIN

33、ATE NOT INTB AXIS 1度非整数修正程式411041 B CL/UCL SENOR ERRORB CL/UCL SENOR FAULT检查SENOR422042 B UNCLAMP TIME OUTB UNCLAMP SENOR FAULT检查SENOR432043 B CLAMP TIME OUTB CLAMP SENOR FAULT检查SENOR441044 PALLET STOPPER ERRORPALLET STOPPER SENOR FAUL榆杳SENOR451045 APC IN MANUAL SW.SWITCH切至 AUTO461046 PALLET GUARD D

34、OOR OPEN既 APC M471047 APC SET UP NOT READYSWITCH切至 OK481048 PALLET TIGHTNESS ERROR榆杳氟密SENOR491049 PALLET NOT READY501050 ATC ARM NOT IN ORI POS榆杳 ARM SENOR511051 B AXIS NOT HOMEB轴没有R帚原黑占 B单蝇帚原黑占521052 Z AXIS NOT ND HOMEZ单由没有R帚2原黑占 Z单睚帚2原黑占531053 B AXIS NOT CLAMPB单由没有CLAMP B *由 CLAMP5455562056 PALLET

35、 UNCLAMP TIME OUTAPC勤作未完成械查SENOR或SOL572057 PALLET CLAMP TIME OUTAPC勤作未完成横查SENOR或SOL582058 PALLET UP TIME OUTAPC勤作未完成检查SENOR或SOL592059 PALLET DOWN TIME OUTAPC勤作未完成检查SENOR或SOL602060 PALLET A IN TIME OUTAPC勤作未完成检查SENOR或SOL612061 PALLET B IN TIME OUTAPC勤作未完成检查SENOR或SOL622062 PLS. EXE. M72APC故障排除提示依指示轨行

36、PALLET UNCLAMP632063 PLS. EXE. M74 OR M73APC故障排除提示依指示轨行APC-UP642064 PLS. EXE. M73APC故障排除提示依指示轨行APC CLAMP652065 PLS. EXE. M77 OR M75APC故障排除提示依指示轨行-PB-in662066 PLS. EXE. M76 OR M75APC故障排除提示依指示轨行672067 PLS. EXE. M75APC故障排除提示依指示轨行 PALLET DOWN682068 PLS. EXE. M76 OR M77APC故障排除提示依指示轨行PA-IN692069 NEED CYCL

37、E START AGAIN押改勤ONE TIME702070 MAG. DOOR NOT CLOSE刀康力未信司不能改勤信司朗刀康力711071 ATC DOOR OPEN TIME OUT检查SENOR或SOL721072 ATC DOOR CLOSE TIME OUT检查SENOR或SOL731073 M80 TIME OUT检查SENOR或SOL741074 M86 TIME OUT检查SENOR或SOL751075 MAG IN MANUAL POSSWITCH切至 AUTO761076 MAG NOT IN POSPMM FAULT重新原黑占定771077MAG MOTOR ERRO

38、RPMM FAULT重新原黑占定781078 MAG BATTERY ERRORPMM FAULT重新原黑占定791079 REMOVE TOOL NOT IN孰彳f REMOVE TOOL IN802080 FILTER DIRTYC.T.S幡罔麟清除渡余罔或更换滤余罔812081 C.T.S. LOW PRESSUREC.T.S1S 力低检查管路是否阻塞822082 TOOL LIFE EXPIRE刀具毒命止以式ATC原黑占校正以式 ATC PMM GEAR PARAMETER PMMtMP105=0,P179=36000,P141=36000P106=?EXAMPL印南刀数P68=40,

39、60刀康诙申浦$一圈刀康位移十（九）把刀，BT50每位移一把刀，焉逵所需醇速，速比1:120（1:108）位移一把 120/10=12（108/9=12）,P106=（刀刀数 40 ）X 12（位移一把=12）=480 （刀刀数60 ）X 12=720BT40每位移一把刀，焉逵所需醇速，速比1:90位移一把 90/9=10, P106=（刀庸刀数 60 ）X 10（位移一把=10） =600若 P106 值太大印P179=360000,P141=360000（PMM417Alarm）,刀南刀数 P68=60,P31=-111P11#0=1 APC,P12#1=0 Automatic param

40、eter setting,P125=Motor type 272P40=100x10,P41=80x10,P43=200x10（刀康余/刀数=60 ）P1#4=1,P40=700,P41=500,P43=2000,P68=60,P106=720,P141=360000,P179=360000（刀庸1 刀数=40 ）P1#4=1,P40=80,P41=50,P43=200,P68=40,P106=480,P141=36000,P179=360001 . KB 1077 MAG MOTOR ALARM1078 MAG BATTERY ALARMPMM-MSG 000 319 3502 .K13.0

41、=1用手输移勤一彳固以上刀套 （P9989#1=1 PMM,MPG FUN.）MAG-KEYB Manual 位置目前用此方式K13.2=1 JOG Mode,X5.2=1（MAG Key=manual）,用 X5.3（MAG CW）X5.4（MAG CCW勤一彳固以上刀套 MAG-KEYB Manual 位置用 JOGB校正 OK（JOG度 P41=510）PMM PARAMETER-11#0 1K13.2=0 正常 MAG JOG One pitch 移勤每位移一把刀，焉逵所需醇速，BT40速比1:100位移一把 100/10=10（刀南刀数 60 ）X 10=600-P106 值=100

42、P105值=0, P179 值=3600003 .ALARM 1078消失用手输移勤校正OKPMM PARAMETER-11#0 14 .ALARM 1077消失 K13.0=05 .PMM 950 alarmDC24V 由 ON/OFF RELAY控制AC220V 由 K1A 控制1. A.Function=2 Data=1 Y72=33 Mode=Auto Y70=001 Start=ST(T-code)B.Function=2 Data=4 Y72=36 Mode=Jog Y70=101 Start=+x,-x(Jog one pitch)K2.1=0押 Mag.CW-key Run,放

43、H Mag.CW-key Mag. Stop in-correct POS.( 速余W1傅)K2.1=1押 Mag.CW-key Run,放H Mag.CW-key Mag. Stop in-nocorrect POS.(one pitch step by step)C.Function=4 Data=1 Y72=65 Mode=Jog Y70=101 Start= STK13.2=1,K15.4=1 Jog Mag.key-in Manual,押主事由停止H 1sec 彳麦放H Mag. Return to 1 POS. D2=1D.Function=4 Data=15 Y72=79 Mod

44、e=Jog Y70=101 Start= STK13.2=1,K15.5=1 Jog Mag.key-in Manual,押主事由停止H 1sec 彳麦放H Mag. PMM 000 alarm P11#0=1setting HOME OKE.Function=0 Data=0xxxx Y72=0 Mode=Jog Y70=101 Start=+x,-xK13.2=1 押 Mag.CW-key Run,押 Mag.CCW-key Stop修正 K13.2=1 押 Mag.CW-key Run,放K Mag.CW-key Mag. Stop (注意 D2 不曾更勤)+XK13.2=1 押 Mag

45、.CCW-key Run,放K Mag.CCW-key Mag. Stop (注意 D2不曹更勤)-X用PMM#41=5 JO密勤刀康取代 MPGD0=Spindle NO., D1=Wait tool NO. D2=Mag. current NO. D3=T-command code NO以式APC手勤找尊O9000程式虢礁，且自勤跳至自勤轨行G7.2(ST)=1P6300#4(ESR)=1P3202#6(PSR)=1D100=90D101=00P6071=6(M6 ARMB刀)O9001P6072=100(M100 APC 自勤更换)O9002P6073=101(M101 APC PA-IN 更换)O9003P6074=102(M102 APC PB-IN 更换)O9004O9000(APC-MAN.)(D100=90,D101=00)#3003=1G4IF1013EQ1GOTO99(MLK)M98P9002N99#3003=0M30O9001(M6-ATC)(P6071=6)#3003=1G4IF#