锂电池规格书

1、储能型磷酸铁锂电池规格书STORAGE LiFePO4 BATTERY SPECIFICATIONS客户名称(Customer):产品型号(Type) :CF12V80Ah发行日期(Issuing Date):Prepared制定Checked审核Approved批准1. 适用范围(Product Scope)本规格书描述了锂离子二次电池的技术要求、测量方法、运输、储存及注意事项。This Specificationdescribes the requirements of the lithium ion rechargeablebattery supplied by2. 电池组特性(Batt

2、ery Group Specifications)Cell电芯Model规格型号IFP8081230-10AhCapacity 容量10 AhRated Voltage标称电压VInternal Resista nee内阻标准< 4 mQCombi natio n Sta ndard配组标准A. 容差 Capacity Differenee< 1%B. 内阻 Resistance()=1 2 mQC. 荷电保持能力 Current-maintaining Ability> 90%D. 电压Combi natio n Method组合方式4串8并4S 8PPile In dex

3、成品参数Rated Capacity标称容量Minimal Capacity最小容量(0.3C5A)Nomi nal Voltage额定电压Max. Charge Voltage 最大充电电压VDischarge cut-off voltage 放电截止电压Charge Curre nt 充电电流5-10AWorki ng Curre nt工作电流10-20AOutput and In put输出端与输入端P+(red) / P-(black)Weight电池重量Dimension 外形尺寸(Lx W< H)168 x 260x 132mm不包含外露开关）Charge Method适用充

4、电Standard 标准5AX 16hrsQuick快速20AX 4hrs.Operat ingTemperature 适用温度Charge充电0C45C; 32oF 113oFDischarge 放电-20C60C; -4°F 149oFMan ageme nt system管理系统Sin glecellover-chargecut-offvoltage单只过压保护值Charge Worki ng voltage过压释放值Sin gle cell un der-discharge cut-off voltage单只欠压保护值Discharge work ing voltage欠压释

5、放值Con diti ons of over-charge and un der-discharge voltage recovery 过、欠压恢复条件With the high-po int voltage reach ing the work ingvoltage 极限电压达到释放值Over-charge cut-off curre nt过流保护值80AShort-circuit protection短路保护Own this ability具备此功能Con diti on for the recovery of over-curre nt and short-circuit protect

6、ion过流 短路保护恢复条件Cut the circuit to automatic recovery断开负载自动恢复单只电芯曲线图 feature curve for single cell3. 技术要求 (Technical Requirements)测试条件(除特别规定)Testi ng Con diti ons (unl ess otherwise specified) 温 度 Temperature:1535°C相对湿度 Relative Humidity: 45%75%大气压 Atmospheric pressure: 86106Kpa充放电性能(Electrical C

7、haracteristics)NO项目(ITEM)测试方法(Testing Instruction)要求(Requirements)1Stan dard Charge标准充电Charg ing the cell in itially with con sta nt curre nt at0.5C and the n with con sta nt voltage at till charge curre nt decli nes to 0.05C先用0.5C恒流充电至，再恒压充电直至充电电流w0.05C2Rated Capacity初始容量Measure discharge capacityw

8、ith discharge curre nt 1Cto cut-off with in 1 hour after sta ndard charge.标准充电方式充电后，以1C电流放电至的容量> 80Ah3Cycle Life循环寿命Measure the capacity after 2000 cycles of sta ndard charge and discharge at 1C curre nt to cut-off> 80 % of RatedCapacity标准充电方式充电后，1C放电至，如此循环2000次后电池 的剩余容量初始容量的80%4StorageCharact

9、eristics储存性能Capacity after 30days storage at 25°C from sta ndardcharge标准充电方式充电后，25 C下储存30天后的容量Rete nti on capacity> 90%剩余容量90%Capacity after 7days storage at 60C from sta ndardcharge标准充电方式充电后，60C下储存7天后的容量Recovery capacity> 90%剩余容量90%环境性能(En viro nmen tai Characteristic)NO项目(ITEM)测试方法(Test

10、ing Instruction)要求(Requireme nts)1Temperature test ing 高低温测试Measure capacity with constant discharge current 0.5C to cut-offat each temperature after standard chargeat 25 C, Percentage as an index of the capacity compared with 100% at 25 C25 C下标准充电方式充电后，在指定温度下0.5C放电至的容量，并以25 C时放电容量为基准计算百分率70% at 0 C

11、100% at 25 C96% at 60 C2Con sta nt temperature /humidity 恒定湿热性能Keep the battery at 40C and 90%RH for 96hrs将电池放入温度为 40C，相对湿度为90%的条件下搁置96 小时Recovery capacity> 85%恢复容量85%机械性能(Mechanical characteristics)NO项目(ITEM)测试方法(Testing Instruction)要求(Requirements)1Vibrati on振动After standard charge, fixed the c

12、ell to vibrationtableand subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute betwee n 10Hz 55Hz, the excursion of the vibration is 1.6mm.The cell shall be vibrated for 30 minu tes per axis of XYZ axes.将标准充电后的电芯固定在振动台上，沿X、Y、Z二个方向各振动30分钟，振幅1.6 mm，振动频率为10Hz55

13、Hz,每分 钟变化为1Hz。The battery shall not rupture, smoke, catch fire, vent or leak and the voltage not be lower tha n 电池应无破裂、冒烟、 着火、泄漏或漏液，并 且电压不低于2IFPacti ngTest ing碰撞After vibration , the battery will be IFPacted 1000 ± 10 times(60 ± 20 times per minute ) with the acceleration of 100 m/s and pu

14、lse lasting time 16ms.2将振动后的电池以峰值加速度为100 m/s的脉冲撞击1000 ±10次(平均每分钟60 ± 20次)，脉冲持续时间为16ms3Free fall自由跌落After IFPacting, the battery will be dropped free five times in three mutually perpe ndicular direct ions from the height of 1.0m onto a hard board with the thick ness of 20mm碰撞实验结束后，将电池由高度为1

15、m的位置自由跌落到置于水泥地面上的20mm厚的硬木板上，从 X、Y、Z正负方向(六 个方向)每个方向自由跌落 1次安全性能(Safe Characteristic)NO项目(ITEM)测试方法(Testing Instruction)要求(Requireme nts)1Short Circuit短路After standard charge，the battery located in a fume hood is to be short-circuited by connecting the positive and negative terminals with an external l

16、oad of less than 50 mQ till the battery casetemperaturehasretur nedto n earambie nttemperature.将标准充电后的电池置于通风橱中，短路其正负极(线 路总电阻不大于50m?),实验过程中监视电池温度变化， 当电池温度卜降到接近初始室温时，结束实验The battery shall not rupture, smoke, catch fire, vent or leak.电池应无破裂、冒烟、着 火、泄漏或漏液2Abno rmalChanging Test过充After discharge to cut-of

17、fwith discharge current1C, the battery is to be subjected to a charg ingcurrent 3C.The specified charging current is to be obtained by connecting a resistor of the specified size and rating in series with the battery.The testtime is to be calculatedusing the formula:tc=2.5c/3(lc)将电池1C放电至后，调节电流 3C充电，

18、充电时间按以 下公式计算：tc = *电池额定容量/(3*制造商给定1C电流)3Over discharge test ing 过放Aftersta ndardcharge, the batterywillbeconn ected with exter nalwith a maximum resista neeload of Q for 24hrs un tilit is completelydischarged and the battery case temperature has retur ned to n ear ambie nt temperature.以标准方式充电后， 将电池正

19、负端以内阻小于欧姆的铜 导线连接24小时.，直至电池完全放电，温度下降到环 境温度4Pun cture穿刺After standard charge，the battery located in a fume hood is to be punctured with a nail (diameter > 1mm) until it is completely discharged and the battery case temperature has returnedto near ambienttemperature将标准充电后的电池置于通风橱中，用直径不小于1mm的针将电池从正面刺

20、穿，直至电池完全放电，温度下降 到环境温度4 电池组基本性能(Basic Characteristics of Battery)电池型号Battery Type4S8P IFP8081230外壳材质 Material of Case环氧树脂Epikote额定电压 Nominal VoltageV额定容量 Nominal Capacity80Ah(0.2C)内阻 Internal Resista nee<400 m?放电截止电压 Discharge Cut-off Voltage最大充电电流 Max Charge Curre nt40A最大放电电流 Max Discharge Curre

21、nt160A最大充电电压 Max Charge Voltage充电方法Charge methodCC/CV (con sta nt curre nt/con sta nt voltage)CC/CV (恒流恒压)尺寸 Dimension长度 Thickness: <260mm宽度 Width: <168 mm高度 Height: <132mm重量Weight约：About:5 电池组保护功能要求(Battery Required Protection Functions)To in sure the safety, charger and the protect ioncir

22、cuit shall be satisfied the items below.As safety device, please use in comb in ati on with the temperature fuse. The sta ndard chargemethod is CC/CV (con sta nt curre nt/con sta nt voltage)为确保安全，充电器和保护电路应符合以下要求。同时请使用装有热熔保险丝的安全装置。标准充电方法为CC/CV(恒流/恒压)参数(product Specificati on)名称(NAME)项目(ITEM)值(value)精

23、度(Precision )单位(unit)过充电压(Over voltage)过充检测电压Ocv3900± 25mV过充恢复电压Vcl3800± 50mV延迟 Delay Time1±S过放电压(Under Voltage)过放检测电压Vcu2300± 80mV过放恢复放电Vcl2700± 100mV延迟 Delay Time100± 50mS充电电流(Charge Curre nt)充电电流OCw 5A过流延迟 OC Delay Time1000± 100mS工作电流(Curre nt)持续放电电流(Con ti nu o

24、us OutputDischarg ing Current )w 20A过放电流(Over Curre nt)过放保护电流OC80± 5A过流延迟 OC Delay Time10± 5mS静态电流(Curre ntCon sumpti on)工作状态Normal Modew 30uA休眠状态Sleep ModewuA短路(Short Circuit)短路电流 SC600± 150A延迟 Delay Timew 1000uS恢复条件Recovery Con diti on断开负载Manual regulati on6 保质期限及产品责任 WARRANTY PERIO

25、D & PRODUCT LIABILITYWarra nty period of this product is 24 mon ths from manu facturi ng code.保质期是从出厂日期(喷码)开始起二十四个月.CHINENGs not responsible for the troubles caused by mishandling of the battery which is clearly against the instructions in this specification.池能公司对因没有按本规格书规定操作而导致的意外不负责任When CHINE

26、NG finds any new facts which require modificati on of this docume nt, we will inform you aga in.一旦池能公司发现本规格书有新的修改细节，我们将再告知。7 包装电池上的标示 INDICATIONS ON BATTERY PACKThe follow ing warnings should be in dicated on the battery packs. 以下警告应注明在包装后的电池上Use a specified charger.使用规定的充电器Do not throw the battery

27、into fire, or heat.不要将电池投入火中或加热Do not short-circuit the battery termi nals不要将电池两端短路Do not disassemble the battery.不要将电池分解拆散8 电池使用时警告事项及注意事项WARNINGS AND CAUTIONS IN HANDLING THE Lithium-io n BATTER YTo prevent a possibility of the battery from leaking, heating or explosion please observe the followi

28、ng precauti ons:为防止电池可能发生泄漏，发热、爆炸，请注意以下预防措施：WARNINGS!1. Do not immerse the battery in water or seawater, and keep the battery in a cool dry surro unding if it sta nds by.严禁将电池浸入海水或水中，保存不用时，应放置于阴凉干燥的环境中2. Do not use or leave the battery near a heat source as fire or heater禁止将电池在热高温源旁，如火、加热器等使用和留置3. W

29、hen recharging, use the battery charger specifically for that purpose充电时请选用锂离子电池专用充电器4. Do not reverse the positive (+) and n egative (-) term in als严禁颠倒正负极使用电池5. Do not connect the battery to an electrical outlet严禁将电池直接接入电源插座6. Do not discard the battery in fire or heat it禁止将电池丢于火或加热器中7. Do not sho

30、rt-circuit the battery by directly connecting the positive (+) andn egative (-) termi nal with metal objects such as wire.禁止用金属直接连接电池正负极短路8. Do not transport or store the battery together with metal objects such asn ecklaces, hairp ins etc.禁止将电池与金属 , 如发夹、项链等一起运输或贮存9. Do not strike or throw the batte

31、ry 禁止敲击或抛掷、踩踏电池等10. Do not directly solder the battery and pierce the battery with a nail or other sharp object.禁止直接焊接电池和用钉子或其它利器刺穿电池CAUTIONS!1. Do not use or leave the battery at very high temperature (for example, at strong direct sunlight or in a vehicle in extremely hot weather). Otherwise, it c

32、an overheat or fire or its performance will be degenerated and its service life will be decreased. 禁止在高温下(炙热的阳光下或很热的汽车中)使用或放置电池, 否则可能会引起电池过热、起火或功能失效、寿命减短2. Do not use it in a location where static electricity is great, otherwise, the safety devices may be damaged, causing hidden trouble of safety.禁止

33、在强静电和强磁场的地方使用 , 否则易破坏电池安全保护装置 , 带来不安全的隐患3. If the battery leaks, and the electrolyte get into the eyes. Do not rub eyes, instead, rinse the eyes with clean running water, and immediately seek medical attention. Otherwise, it may injure eyes or cause a loss of sight.如果电池发生泄露 , 电解液进入眼睛 , 请不要揉擦 , 应用清水冲洗眼睛 , 并立即送医院治疗 , 否则会伤 害眼睛4. If the battery gives off an odor, generates heat, becomes disc