机器人专业词汇中英文对照.

1、ACAS Applicator Cleaner Air Supply 雾化器清洗器供气pACS Applicator Cleaner Solvent Pilot 雾化器清洗器溶剂控制阀ACS Applicator Cleaner Solvent 雾化器清洗器溶剂ACVA Applicator Cleaner Vacuum Air 雾化器清洗器真空空气ACDA Applicator Cleaner Drying Air 雾化器清洗器干燥空气BEAR Bearing Air 轴承空气BAO Bearing Air OK 轴承空气正常BRAKE Brake Air Turbine 涡轮刹车空气pBW

2、 Bell Wash Pilot 旋杯清洗控制阀BWS Bell Wash Supply 旋杯清洗供应AIR Color Change Air Supply 换色空气供应SOL Color Change Solvent Supply 换色溶剂供应CP# Color Pilot (#) = Color 颜色控制阀（#）= 颜色DUMP Dump 排放DAT Drive Air Turbine 涡轮驱动空气E-STAT Electrostatics 静电pIW Injector Wash Pilot 注射器清洗控制阀IWS Injector Wash Supply 注射器清洗供应PAINT Pai

3、nt 油漆PAP Purge Air Pilot 冲洗空气控制阀pCC Pilot Color Change 换色控制阀PCE Process Control Enclosure 工艺控制柜pDUMP Pilot Dump 排放控制阀PDP Power Distribution Panel 配电柜PIE Process Interface Enclosure 工艺接口柜PREG Pilot Regulator 调节器控制阀PR# Paint Return (#) = Color 油漆回路（#）= 颜色PS# Paint Supply (#) = Color 油漆进路（#）= 颜色pPS Pur

4、ge Solvent Pilot 冲洗溶剂控制阀pTRIG Pilot Trigger 触发器控制阀PTS Pilot Trigger Supply 触发器供应控制阀RP Robot Purge 机器人净化SA1 Shaping Air (Bell Applicator) 成形空气（旋杯雾化器）SA2 Shaping Air (Bell Applicator) 成形空气（旋杯雾化器）SAP Shaping Air Pilot 成形空气控制阀SAS Shaping Air Supply 成形空气供气SCC System Control Console 系统控制柜TDP Turbine Drive

5、 Pilot (Bell Applicator) 涡轮驱动控制阀（旋杯雾化器）TURB Turbine Drive Supply 涡轮驱动供气Purge System Maintenance净化系统维护- Purge System Diagnostics净化系统诊断- Purge System Testing andCalibration净化系统测试和校准- Purge Cycle Troubleshooting净化循环排错 Color Changer Assembly换色器组件- Color Changer Valve Maintenance换色阀门维护 SolvAir Module Set

6、up and Maintenance溶剂空气模块设置和维护 3 Valve IK Gear Pump3阀门1K齿轮泵- Pump Block Pressure Sensor泵的压力传感器 Process Control Maintenance工艺控制维护- Fluid Presets Maintenance流体预设值维护- E-stat Presets Maintenance静电预设值维护- Preset Override Maintenance强制预设值维护- Color Change Maintenance换色维护 Pepperl & Fuchs ISB SettingsPepperl &

7、 Fuchs ISB设置 Robot Software Maintenance机器人软件维护- I/O Re-configurationI/O 重新配置- Robot File Copy机器人文件复制- Robot System Variables EditingTransducer Operations比例阀的操作- Shaping Air Control成形空气的控制- D/Q Shaping Air Control ModuleD/Q 成形空气控制模块- Turbine Speed Control涡轮速度控制- Keyence Digital Fiber SensorKeyence 数字

8、光线传感器 Fluid Calibration - Beaker Method流体校准 量杯的方法 System Configuration Maintenance系统配置维护- System Colors Maintenance系统颜色维护- Styles Maintenance车型维护- Option Maintenance选项维护- PW3 SetupPW3 设置机器人系统变量编辑- Software Archive软件存档- Backup a Robot Image备份一个机器人镜像- Restore a Robot Image恢复一个机器人镜像 Paintworks III Soft

9、ware MaintenancePaintworks III软件维护- Creating a Norton Ghost 2003Boot Disk Set创建一个Norton Ghost2003 启动盘- Backing Up Your PAINTworks IIIGUI备份你的PAINTworksIII GUI。- Copying Your Ghost Image Filesto CDs把你的Ghost 镜像文件复制到CDs。- Restoring Your PAINTworks IIIGUI恢复你的PANITworks III GUI。pAIR PAP Pilot input for Pu

10、rge Air净化空气的驱动输入pSOLV PSP Pilot input for Purge Solvent净化溶剂的驱动输入AIR CCAS Purge Air supply input净化气源输入SOL CCSS Purge Solvent supply input净化溶剂供应输入pCC PCC Pilot for Color Changer operation. When this input is enabled, thepurge air and solvent mixture will be directed to the color changermanifold as aer

11、ated solvent.换色器操作的驱动。这个输入被激活时，净化空气和溶剂混合物会直接通向换色器多只管，像充气的溶剂一样。2T Output 2T Secondary output (used for Applicator Wash). Solvent or air or theaerated mixture is always available at this port. If it is not requiredin the system, the port must be plugged.二次输出（用于雾化器清洗 ）。在这个端口一直有溶剂、空气或者混物。如果系统没有要求，这个端口必须

12、被塞紧。1K Process Assembly with a Regulator 含调整器的1K 工艺组件EO-4696-511-000 Rev. A Sheet 1 of 1 EO-4696-511-000 Rev. A版 第一页/共一页COLOR CHANGER (24 COLOR MAX.) 换色器 (最多24种颜色)WASH 清洗INJECTOR 注射器WASH 清洗PAINT ENABLE 喷漆激活TRIGGER 触发器BELL WASH 杯头清洗PAINT 油漆SOLV/AIR 溶剂/空气AIR 空气RECOVERY 回收DUMP 排放2K Process Assembly wit

13、h a Regulator Schematic 含调整器的2K工艺组件示意图EO-4696-517-000 Rev. C4 Sheet 1 of 1 EO-4696-517-000 Rev. C4版 第一页/共一页COLOR CHANGER (4 COLOR MAX.) 换色器 (最多四种颜色)INJECTOR WASH 注射器清洗PAINT ENABLE 喷漆激活TRIGGER 触发器BELL WASH 杯头清洗CAT 架子DUMP 排放FLUSH 齐平AIR1 空气1SOLV/AIR 溶剂/空气WASH 清洗SOL2 溶剂20-500 PSI 0-500 PSIApplicator Int

14、erface 雾化器接口ET-4696-890-001 Rev. A Sheet 1 of 1 ET-4696-890-001 Rev. A版 第一页/共一页ORIGIN OF TOOL FRAME 工具坐标系原点BOLT HOLES 螺栓孔FAN 风扇FAN 风扇FACE PLATE 面板TOOL FRAME 工具架EDGE OF BELL CUP 杯头边缘SECTION A-A AA截面SCRMO00000277N (6) SCRMO00000277N (6)M6 Craftech Scr. M6 工艺技术螺丝Torque to 1.25 Nm 转矩至1.25 NmPINLM0050000

15、12S PINLM005000012S工作特征备注最高运行电压 90kV正常旋转速度 20到45 kRPM最高旋转速度* 45 到60 kRPM喷漆正常流速 0到300 cc/min最大流速 500 cc/min正常喷漆应用压力 90到120 psi最大喷漆应用压力 150 psi粘度范围 50到200 cps空气空气压强供应 85 psi min空气供应过滤: 级别1 按照DIN ISO 8573-1空气消耗涡轮支承 57 slpm涡轮在60，000 rpm* 119 slpm成形空气 70到500 slpm密封空气 0到50 slpm (通常不需要)电气能量供应 120 v 50/60 H

16、zTube Requirements 管道要求ET-4696-890-002 Rev. B1 Sheet 1 of 1 ET-4696-890-002 Rev. B1版 第一页/共一页SECTION A-A A-A截面BRAKE 制动空气PAINT 油漆管路SPEED 速度BEAR 轴承空气SEAL 密封空气TURB 涡轮空气WASH 清洗NOTES: 注意:1. TUBING SHOULD BE INSTALLED WITH ROBOT IN ZERO POSITION.管道应与机器人一起安装在零点位置。SECTION B-B B-B截面SLOTTED CHEESE HEAD 槽形奶酪状顶部

17、MACHINE SCREW 加工螺丝NYLON 6/6 30% SHORT 短的尼龙6/6 30%FIBER GLASS FILLED 玻璃纤维填充Torque to .55 Nm/4.8 In. Lbs. 转矩至.55 Nm/4.8 In. LbsColor Changer, Pump and Pump Block 换色器，泵和泵座CHANGER-PUMP Rev. A Sheet 1 of 1 换色器-泵 Rev. A版 第一页/共一页Air 空气Solvent 溶剂Solvent Supply Valve 溶剂供应阀门Air Supply Valve 空气供应阀门Solvent Wash

18、 Line 溶剂清洗管路Pump Flush Valve 泵冲洗阀门Dump Valve 2 排放阀门2Dump Valve 2 排放阀门2Pressure Transducer P/I 压力传感器P/IFluid Regulator 流体调整器Reclaim 回收Bell Wash Valve 杯头清洗阀门Injector Wash Valve 注射器清洗阀门Trigger Valve 触发器阀门Paint Enable Valve 喷漆激活阀门Gear and Shaft Assembly 齿轮和轴体组件Drive Shaft 驱动轴Drive Gear 驱动齿轮Key 销子Rear Plate 后板体Dowel (2) 销子(2)Arbor 柄轴Driven Gear 驱动齿轮Gear Plate 齿轮板Front Plate 前板体Seal (3) 密封(3)Seal Housing 密封套M5x20 Soc. Hd. Scr. M5x20内六角螺丝Torque to 7.9 Nm/ 70 In. Lbs. 转矩至7.9 Nm/ 70 In. LbsM5x4