版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、精品资料欢迎阅读 智慧树知到模拟电子技术基础(西安邮电大学版)章节测试答案 智慧树知到模拟电子技术基础(西安邮电大学版)章节测试答案第一章1、Which of the following is not a commonly used semiconductor material’? ( )A:carbonB:leadC:siliconD:germanium答案: lead2、The characteristic of an ideal diode are those of a switch that can conduct current( ) .A:in both directi
2、onsB:in one direction onlyC:in both directions but in only one direction at a timeD:depends on the circuit it is used in答案: in one direction only3、When a diode is doped with either a pentavalent or a trivalent impurity its resistance will ( ) .A:increaseB:decreaseC:make the resistance stable against
3、 variation due to temperature答案: decrease4、The piecewise linear model, equivalent circuit of the diode consists of ( ).A:a junction capacitor, a battery, a small resistor, and the ideal diodeB:a battery, a small resistor, and the ideal diodeC:a battery and the ideal diodeD:the ideal diode答案: a batte
4、ry, a small resistor, and the ideal diode5、When a p-n junction is reverse-biased, its junction resistance is ( ).A:highB:lowC:determined by the components that are external to the deviceD:constantly changing答案: high第二章1、What is the value of the voltage dropped across forward-biased silicon diodes th
5、at are connected in parallel with each other? ( ).A:11.3 VB:35 VC:7 VD:4 V答案: 7 V2、The resistor voltage and resistor current in this circuit are ( ).image.pngA:10 V, 5 mAB:11 V, 2 mAC:11 V, 11 mAD:2 V, 11 mA答案: 11 V, 11 mA3、Which of the following circuits is used to eliminate a portion of a signal?
6、( ).A:ClipperB:DamperC:Voltage multiplierD:Voltage divider答案: Clipper4、The circuit shown here is a ( ). image.pngA:series clipperB:parallel clipperC:series clamperD:shunt clamper答案: parallel clipper5、The Zener diode must be operated such that ( ).A:image.pngB:image.png is less than the specified ima
7、ge.pngC:the applied voltage is greater than image.png D:All of these答案: All of these第三章1、In the active region, the base-emitter junction ( ).A:and the base-collector junctions are both forward-biasedB:and the base-collector junctions are both reverse-biasedC:is forward-biased while the base-collecto
8、r junction is reversed-biasedD:is reverse-biased while the base-collector junction is forward-biased答案: C2、A BJT has measured dc current values of image.png = 0.1 mA and image.png= 8.0 mA. When IB is varied by 100 μA, IC changes by 10 mA. What is the value of the βac for this devi
9、ce?( ).A:80B:10C:100D:800答案: C3、When a BJT is operating in the active region, the voltage drop from the base to the emitter image.png is approximately equal to the ( )。A:base bias voltageB:base current times the base resistorC:diode drop (about 0.7 V)D:emitter voltage答案: C4、BJTs are commonly used as
10、 ( ).A:the primary components in amplifiersB:series damper circuitsC:the primary components in rectifiers答案: A5、The condition where increase in bias current will not cause further increases in collector current is called ( ).A:cutoffB:saturationC:active operation答案: B第四章1、When a BJT is biased in the
11、 cutoff region the collector-to-emitter voltage is typically equal to ( ).A:the emitter voltageB:03 VC:the collector current times the collector resistorD:the collector supply voltage答案: D2、Calculate the collector-emitter voltage for this emitter-stabilized circuit.( ) image.pngA:32 VB:10.68 VC:1335
12、 VD:14.24 V答案: 4.32 V3、The difference between the resulting equations for a network in which an npn transistor has been replaced by a pnp transistor is ( ).A:the values of the resistorsB:the value of βC:the sign associates with the particular quantities答案: C4、The term quiescent means ( ).A:midp
13、oint-biasedB:at restC:activeD:inactive答案: D5、Voltage-divider bias stability is ( ).A:dependent on alpha B:dependent of betaC:dependent on the collector resistorD:independent of beta答案: D第五章1、Given this configuration, determine the input impedance if VS = 40 mV, Rsense = 0.5 kΩ, and the input c
14、urrent is 20 μA.( )image.pngA:5 MΩB:822 MΩC:1,500 ΩD:582 kΩ答案: C2、The image.png transistor model replaces the ( ) with the junction diode’s ac resistance.A:collector-base junctionB:collector-emitter junctionC:emitter—base junction答案: C3、Calculate the voltage ga
15、in for this circuit. ( )image.pngA:-137.25B:-8.4C: -7.91D:-16.34答案: A4、A transistor amplifier has an input signal applied to its emitter terminal and an output signal taken from its collector terminal. The amplifier is a(n) ( ).A:common-emitter amplifierB:common-base amplifierC:common-collector ampl
16、ifierD:emitter follower答案: B5、The voltage gain of a very well-designed common collector amplifier configuration, using a pnp transistor, is ( ).A:about -0.9B:about 0.9C:in the range 0.95 to 0.99D:in the range -0.95 to -0.99答案: C第六章1、Shockley’s equation defines the ( ) of the FET and are unaffe
17、cted by the network in which the device is employed.A:image.png characteristicsB:drain characteristicsC:input/output characteristicsD:transfer characteristics答案: D2、For an n-channel depletion MOSFET, image.png= 8 mA and image.png = -6 V. If image.png= 0.8 V, what is the value of the drain current, i
18、mage.png? ( )A:8 mAB:10.25 μAC:10.28 mAD:6 mA答案: C3、The region of the JFET drain curve that lies between pinch-off and breakdown is called ( ).A:the constant-voltage regionB:the ohmic regionC:the saturation region答案: C4、In the family of FETs, you can expect to find ( ).A:an n-channel typeB:a p-ch
19、annel typeC:unipolar structure答案: ABC5、FETs usually ( ).A:are less sensitive to temperature change than BJTsB:have a higher input impudence than BJTs C:are smaller in construction than BJTs答案: ABC第七章1、This graphical solution represents ( ).image.pngA:fixed bias for an n-channel JFETB:voltage-divider
20、 bias for an n-channel JFETC:self bias for an n-channel JFET答案: C2、Generally, it is good design practice for linear amplifiers to have operating points that close to ( ).A:are close to saturation levelB:the cut-off regionC:the midpoint of the load line答案: C3、Which of the following biasing circuits c
21、an be used with E-MOSFETs? ( )A:self biasB:zero biasC:drain-feedback biasD:current-source bias答案: C4、The primary difference between JFETs and depletion-type MOSFETs is ( ).A:JFETs can have positive values of image.png and levels of drain current that exceed image.pngB:depletion-type MOSFETs can have
22、 positive values of image.png and levels of image.png that exceed image.pngC:depletion-type MOSFETs can have only positive of image.pngD:JFETs can have only positive values of image.png答案: B5、A JFET can be biased in several different ways. The common method(s) of biasing an n-channel JFET
23、 is(are) ( ).A:self-bias configurationB:voltage-divider bias configurationC:fixed-bias configuration答案: ABC第八章1、The FET version of the BJT’s common-emitter configuration is the ( ) circuit.A:common-sourceB:common-gateC:common-drainD:common-current答案: A2、Calculate the input impedance for this F
24、ET amplifier. ( )image.pngA:image.pngB:image.pngC:image.pngD:image.png = would depend on the drain current image.png答案: 3、Design this circuit for a voltage gain of 10. You have to calculate the value of resistor image.png and image.png. It is desired that the transistor operate with a relatively hig
25、h value of image.png. For this device, a high value of image.png is defined as image.png. ( )image.pngA:image.pngB:image.pngC:image.pngD:image.png答案: 4、The ( ) amplifier has high input impedance, low output impedance, and low voltage gain.A:common-gate B:common-drainC:common-source答案: B5、The ( ) FET
26、 amplifier has low input impedance, high output impedance, and high voltage gain.A:common-gateB:common-drainC:common-source答案: A第九章1、Calculate the low frequency break point due to the capacitor image.png for this BJT amplifier. ( )image.pngA:image.pngB:image.pngC:image.pngD:image.png答案: 2、If several
27、 identical stages of amplifiers, each having the exact same upper and lower cutoff frequencies, are connected in cascade, then the bandwidth of the resulting amplifier will ( ).A:increaseB:remain unchangedC:decreaseD:be equal to the sum of all the individual bandwidths答案: C3、A 3-dB drop in β oc
28、curs at ( ).A:image.pngB:image.pngC:image.pngD:image.png答案: 4、Negative dB values represent ( ).A:power gainB:power lossesC:power values that do not change答案: B5、An amplifier has a midband power gain of 24,500. What is the value of the power gain in dB for the circuit? ( )A:87.78 dBB:43.9 dBC:39 dB答案
29、: B第十章1、Under difference-mode operation, the difference-mode voltage gain for this circuit is ( ).image.pngA:0397B:80C:40D:08答案: C2、The operational amplifier will only slightly amplify signals ( ).A:when the supply voltages are more then ±25 VB:when the supply voltages are less then ±5
30、 VC:that are common on both the inputsD:that are different on both the inputs答案:C3、The inverting and noninverting inputs to an op-amp are used to drive a(n) ( ) amplifier.A:invertingB:noninvertingC:differentialD:open-loop答案: C4、When a given op-amp has a common-mode input of 10 V, the output of the d
31、evice is 10 V. When the device has a differential input of 2 mV, the output of the device is 10 V. What is the CMPR of the device? ( )A:5 : 1B:5000 : 1C:1000 : 1D:5,000,000 : 1答案: B5、The bandwidth of an amplifier is ( ).A:the range of frequencies over which gain remains relatively constant B:the ran
32、ge of frequencies between the lower and upper 3 dB frequenciesC: the range of frequencies found using image.png答案: ABC第十一章1、 If the input voltage is 0.25 V and the output is -2.5 V, the value ofimage.png must be ( ).image.pngA:40.0 kΩB:20.0 kΩC:16.0 kΩD:0 kΩ答案: B2、The output
33、voltage, VO, is given by ( ).image.pngA:image.pngB:image.pngC:image.png答案: 3、A summing integrator is an op-amp integrator that has ( ).A:multiple feedback capacitorsB:multiple input resistorsC:multiple input resistors and feedback capacitors答案: C4、A second order low-pass filter has a high-end roll-o
34、ff of ( ).A:60 dB/octaveB:40 dB/decadeC:20 dB/octaveD:6 dB/decade答案: B5、An active filter that provides a constant output for input signals above image.png is called an ideal ( ).A:low-pass filterB:high-pass filterC:bandpass filter答案: B第十二章1、A class B amplifier (not push-pull) ( ).A:conducts through
35、360° of the input waveformB:conducts through 180° of the input waveformC:conducts between 180° and 360° degrees of the input waveform, depending on the amount of dc biasD:conducts through less than 180° of the input waveform答案: B2、Crossover distortion in class B amplifiers is pre
36、vented by ( ).A:biasing the transistors deeply into cutoffB:biasing the transistors slightly above cutoffC:using complementary-symmetry transistorsD:increasing the load resistance答案: B3、The maximum theoretical efficiency of an RC-coupled class A amplifier is ( ).A:25%B:50%C:78.5%D:99%答案: A4、Power amplifiers are typically used to drive low impedance loads.( )A:对B:错答案: A5、The power that an amplifier delivers to a load is equal to the difference between the power that the
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 军事行业安全工作总结
- 构建良好班级氛围的培训总结
- 《新脑血管病的预防》课件
- 2024年江苏省泰州市公开招聘警务辅助人员辅警笔试自考题2卷含答案
- 2022年江西省景德镇市公开招聘警务辅助人员辅警笔试自考题1卷含答案
- 2021年青海省西宁市公开招聘警务辅助人员辅警笔试自考题2卷含答案
- 2023年湖北省宜昌市公开招聘警务辅助人员辅警笔试自考题2卷含答案
- 2022年河南省洛阳市公开招聘警务辅助人员辅警笔试自考题1卷含答案
- 2024年云南省丽江市公开招聘警务辅助人员辅警笔试自考题1卷含答案
- 《危险货物运输包装》课件
- 书法知识之章法布局
- 2023乙型肝炎病毒标志物临床应用专家共识(完整版)
- 23J916-1:住宅排气道(一)
- 储能项目用户侧投资测算表
- 【解析】教科版(广州)2023-2023学年小学英语五年级上册分类专项复习卷:阅读
- 月日上午王一凡把问题当做教育的资源 优秀奖
- 脊柱四肢及肛门直肠检查
- 高中政治期末综合检测部编版选修1
- 铸造基础知识及常见铸造缺陷简介课件
- 历史(中职)PPT全套教学课件
- 药物分离技术教材吴昊课后参考答案
评论
0/150
提交评论