最新加工中心精度检验规范资料

1、NO.日沛電腦配件（上海）有限公司RI PEI computer accessory (Shanghai) Co., Ltd.加工中心精度检验規範机型：MODEL 机号：SERIAL NO. 目录CATALOGUE1.0静态精度检查 6页PAGESTATIC ACCURACY INSPECION2.0定位精度检查 1页PAGEPOSITION ACCURACY INSPECTION3.0重复精度检查1页PAGEREPETITIONAL ACCURACY INSPECTION4.0循圓精度1页PAGEPALLET ACCURACY5.0 附件 .页 PAGEACCESSARY共页PAGE中國上海

2、松江區新橋鎮申港路 3636號No.3636 Shen gga ng Road,X in Qiao Son gjia ng Shan ghai China核准者CONFIRMED检验者CHECKED检验 日期DATEMCV F01S001Q301000003940331-71.0 静态精度 STATIC ACCURACY INSPECTION单位 Unit : mm检查项目In spect ion item许可差Permissible deviati on测试方法图Measuri ng method diagram实 际 测量值Measured value项次NO1.11.2床台X轴方向运动之

3、真直度a.Straight nes$ X-Z of the Xaxismoveme nt床台丫轴方向运动之真直度面内b.Y-Z面内a.Straight nes$ X-Z of the 丫axismoveme nt面内fta ri0.06/10000.06/1000b.Y-Z面内1-1单位 Unit : mm检查项目In specti on itemNO床台X轴方向之 运动与其上面之 平行度Parallelismbetwee n1.3 movement in Xaxis directi on and table upper surface测试方法图Measuri ng method diagra

4、m许可差Permissible deviati onX 三 5000.02500v X 三 8000.025800v X 三 1250 0.031250V X 三 2000 0.04实 际测量值Measured value1.4丫 三 5000.02500V 丫 三 8000.025800V 丫 三 1250 0.031250V 丫 三 2000 0.04床台丫轴方向之运动与其上面之 平行度Parallelismbetwee n movement in 丫 axis directi on and table upper surface1.5X轴方向运动与 床台基准沟侧面 之平行度Paralle

5、lism betwee n movement in X axis directi on and Side surface oftable refere nee slot每300mm的量测距离下 许可差为0.015mm0.015for a measuri ng len gth of 3001-2单位 Unit : mmNO检查项目In speeti on item测试方法图Measuri ng method diagram许可差Permissibledeviatio n实 际测量值Measured value各轴方向a.相互运动X-Y之直角度轴Perpe ndicuPlacelarityBetw

6、ee nmoveme ntin X axisdirecti onand Y axisb.directi onX-Zand Z axis轴directi onPlace1.6A .0.012/3000.012/300c.Y-Z轴Place主轴中心线与床 台面之直角度Perpe ndicularitybetwee n cen terl ine1.7of main spi ndleand table surface.0.012/300旋径每300Per3000.0151-3单位 Unit : mm项 次NO检杳项目In specti on item测试方法图Measuri ng method dia

7、gram许可差Permissible deviati on实际测量值Measured value1.8主轴孔内面之偏 摆Run out of spin dle taper holeIt-LC.41 I1固定端At spin dle side end of tes bar0.005固定端300处At 300 position0.0151.9主轴轴线与Z轴 轴线运动间的平 行度Parallelism betwee n the spin die axis and the Z-axis moti onFi - ;iJo-a:0.015/300b:0.015/3001.101.11主轴在Z轴方向之移（松

8、）动量Moveme nt of mainspindle in Z axisdirecti on主轴端面之偏摆Run out of mainspin dle outersurface1.12主軸外面之偏擺Run out of mainspin dleoutersurface0.0050.010.01mm1.16旋轉檯旋轉偏擺Table runo ut(Z)0.005mm1.17車刀角度換刀後重複定位精度Repeatability of tool an gle after tool cha nge.0.001mm1.18車刀角度停止後重複定位精度Repeatability of tool an g

9、le after tool stop.0.001mm1.工後定位machi ning part精度Repeatability ofngle after01mm1.21主軸振動檢測Spin dle vibrati on detecti on=0.6mm/s(Ref)2.0 定位精度检查 Positi oning accuracy in specti on单位 Unit : mm项次NO检查项目In specti on item测试方法图Measuri ng method diagram许可差Permissible deviati on实 际测量值Measured value2.1直线运动之定位精

10、度ISO230-2 循环次数：2次 X Positi oning accuracy of straight li ne moveme ntBy ISO230-2 Cycle times Y:Two times2.2回转运动之定位精度Positi oningaccuracyof straightli nemoveme ntByISO230-2Cycletimes:TwotimesL 三 10000.011000V L 三 20000.015L 三 20000.02单位 Un it: sec15ff1-73.0 反复精度检查 Repetiti on accuracy in spect ion单位

11、Un it: sec项次NO检查项目In specti on item直线运动之 反复定位精 X 度ISO230-2Positi oningrepeatability3.1of straightli nemoveme nt3.2ByISO230-2Cycle times:Two times Z回转运动之 重复定位精 度ISO230-2Positi oningrepeatabilityof straight Clinemoveme ntByISO230-2Cycle times:Two times测试方法图Measuri ng method diagram许可差Permissible devia

12、tion0.006ff实 际测量值Measured value单位 Un it: sec1-8单位 Un it: sec3.0 反复精度检查 Repetiti on accuracy in spect ion项次NO检查项目In specti on item测试方法图Measuri ng method diagram许可差Permissible deviation实 际测量值Measured value0.006Max reversal value 最大反沖值Positi on accuracy qualified to3.3ISO 230-24.0 循圓精度检查 Repetiti on accuracy in spect ion单位 Un it: sec项 次NO检杳项目I