Chapter62Physico-chemicaltreatment：62章物理化学处理.doc

Chapter 6.2 Physico-chemical treatmentNotes on this chapterThe material presented here gives an overview of the main technologies presently used in the field of physico-chemical treatment. The special item of stabilisation and solidification is addressed separately in Chapter 6.4.The techniques addressed in this chapter should be considered in relation to general aspects of legislation and standardisation, which differ considerably between countries and groups of countries (such as the European Union). Most treatment processes are landfill pre-treatment. Among the most important influences on treatment choices are the types and permit conditions of available landfills, whether they are simple landfills (sanitary or secure) or co-disposal sites, and whether they accept storage of stabilised wastes. The selection, and sophistication, of a chosen treatment will depend on these landfill requirements and on their operating parameters and standards.The slides cover the main aspects of the different technologies, but they can be extended with additional technical aspects according to the state of art in the countries (or groups) on the training course. The slides can only address broad issues relating to the treatment techniques. Trainers should add or adapt details of equipment, construction and management aspects to meet local circumstances.Valuable sources of additional information include technical documents from conferences, technical reviews and magazines, particularly those published by the national environmental protection agencies, national standards institutes and international associations such as the International Solid Waste Association (ISWA), FEAD and EURITS. List of slidesTitle slideSlide 2 Physico-chemical treatmentSlide 3 Physico-chemical treatment facilitiesSlide 4 Physico-chemical treatment in central treatment facilitySlide 5 Treatment residuesSlide 6 Physical processesSlide 7 SeparationSlide 8 AdsorptionSlide 9 SedimentationSlide 10 Sedimentation - exampleSlide 11 FlotationSlide 12 Drying and evaporationSlide 13 Drying and evaporation - exampleSlide 14 Chemical processesSlide 15 Reduction and oxidationSlide 16 Oxidation in practice Slide 17 Reduction in practiceSlide 18 NeutralisationSlide 19 PrecipitationSlide 20 Other chemical processesSlide 21 Combined physical and chemical processesSlide 22 Physico-chemical treatment Slide 23 Key considerationsSlide 24 SummaryBackground notes 1 Physical and chemical methods for the treatment of wastes involve a range of different but commonly-used treatment processes, often used in combination, to separate or transform hazardous substances. By definition they do not include biological processes.2 The many advantages of physico-chemical treatment processes include the fact that little energy is required.3 Typically, physical treatment processes are long-established and relatively low-tech. Chemical treatment methods are also well-established. As a result these two treatment methods may require relatively lower capital investment levels than some other methods such as thermal processing. They do however still require a high level of expertise to ensure their safe operation. 4 Physico-chemical treatment of wastes can be used to deal with both solid and liquid wastes, as well as organic and inorganic wastes, providing the appropriate processes are used. However, both physical and chemical processes are specific for each waste, requiring an in-depth knowledge of the waste to be treated and an understanding of a variety of applications.5 Chemical reactions must be closely monitored and checked by a qualified laboratory.The presence of substances which inhibit the catalyst, where used, can affect the success of the process.6 The facility design and equipment selection for physical-chemical treatment of waste are determined by the properties and characteristics of the wastes which will be treated.They are also influenced by the national and regional regulations and standards which are in force. Sources of further informationBatstone, R; Smith, JE & Wilson, DC editors (1989) The safe disposal of hazardous wastes: The special needs and problems of developing countries World Bank, Washington, Technical paper No 93 Vol 2 in 3 volumes ISBN 0-8213-1144-1 (available as pdf files from /publications/)Guyer, Howard H (1998) Industrial processes and waste stream management Wiley ISBN 0-4712-9984-7ISWA (2002) Safe hazardous waste management systems: a state of the art guide for decision makers forthcoming from LaGrega, MD; Buckingham, PL; Evans, JC & ERM Group (1994) Hazardous Waste Management McGraw Hill, New York ISBN 0-07-019552-8Lohwongwatana, B; Soponkanaporn, T & Sophonsridsuk, A Industrial hazardous waste treatment facilities in Thailand Waste Management & Research Vol 8 No 2Nash, JM; Cheung, B; Fung, CH; Lei PK, Mak, PW; Rootham, RC; Stokoe, MJ & Tong, R (1991) Control and treatment of hazardous (chemical) waste in Hong Kong Waste Management & Research Vol 9 No 3Ravishankar, R (1990) Opportunities and constraints for cement kiln incineration in Malaysia, Waste Management & Research Vol 8 No 2 Razzell, WE (1990) Chemical fixation, solidification of hazardous waste, Waste Management & Research, Vol 8 No 2 Technical guidelines from the Secretariat of the Basel Convention UNEP (1991) Hazardous waste policies and strategies a training manual, Technical report No 10 UNEP Industry & Environment Programme Activ