Agilent 34401A产品使用手册

1、Agilent 34401A品使用手册-CAL-FENGHAI.Network Information Technology Company.2020YEAR PAGE PAGE 5The Agilent Technologies 34401A is a 6 1/2-digit, high-performance digital multimeter. Its combination of bench-top and systemfeatures makes this multimeter a versatile solution for your measurement needs now

2、and in the future.Agilent34401A61/2数字的顶端和系统特征为你的测量需要使这一个万用表成为用途广泛的解决现 在和未来。Convenient Bench-Top FeaturesHighly visible vacuum-fluorescent display Built-in math operationsContinuity and diode testfunctionsHands-free, Reading HoldfeaturePortable, ruggedized case with non-skidfeet方便的长椅子-顶端扮演重要角色高度地看得见的

3、真空-日光灯展览内建的数学行动连续性和两极管测试功能免动手的, 读把握特征手提式的, 用非橇的脚使情形坚固了Flexible System FeaturesGPIB (IEEE-488) interface and RS-232interfaceStandard programming languages: SCPI, Agilent 3478A, and Fluke8840Reading rates up to 1000 readings persecondStorage for up to 512readingsLimit testing with pass/failsignalsOpti

4、onal 34812A BenchLink/Meter Software for MicrosoftWindowsTM灵活的系统作用GPIB(IEEE-488) 接口和 RS-232 接口标准程序语言SCPI ， Agilent 3478 A, 和Fluke 8840阅读评估每秒达 1000 阅读储藏为达 512 阅读以途径/不及格尝试的界限向可选择的 34812 BenchLink/公尺软件为微软WindowsTMThe Front Panel at a Glance前面板一瞥Measurement Function keysMath Operation keysSingle Trigger

5、 / Autotrigger / Reading Hold keyShift / Local keyFront / Rear Input Terminal SwitchRange / Number of Digits Displayed keysMenu Operation keys测量功能键数学操作键信号触发 /Autotrigger/ 阅读保持键转换 / 恢复键前面的 / 后面的输入终端转换键范围 / 数字宽度显示键主菜单操作键The Front-Panel Menu at a GlanceThe menu is organized in a top-down tree structure

6、 with three levels前面板菜单一瞥菜单在由上而下的树结构被三个水平所组织A: MEASurement MENUA: 测量菜单1: AC FILTER 2: CONTINUITY 3: INPUT R 4: RATIO FUNC 5: RESOLUTION1: AC 过滤器 2: 连续性 3: 输入 R4: 比 FUNC5: 决议B: MATH MENUB: 数学菜单1: MIN-MAX 2: NULL VALUE 3: dB REL 4: dBm REF R 5: LIMIT TEST 6: HIGH LIMIT 7: LOW LIMIT1: 最小-最大 2: 无效的值 3:

7、分贝损耗率 4: dBm 参考 R5: 极限测试 6: 最高界限 7: 低的界限C: TRIGger MENUC: 触发菜单1: READ HOLD 2: TRIG DELAY 3: N SAMPLES1:阅读保持 2: 追踪延迟 3: N 抽样D: SYStem MENUD: 系统菜单1: RDGS STORE 2: SAVED RDGS 3: ERROR 4: TEST 5: DISPLAY 6: BEEP 7: COMMA 8: REVISION1: RDGS 存贮 2:保存 RDGS3: 错误 4: 测试 5: 演示 6:声音 7: 逗点 8:修 订E: Input / Output

8、MENUE: 输入 / 输出菜单1: HP-IB ADDR 2: INTERFACE 3: BAUD RATE 4: PARITY 5: LANGUAGE1: HP-IB 的 ADDR2: 接口 3: 波特率 4: 奇偶 5: 语言F: CALibration MENU*F: 刻度菜单*1: SECURED 1: UNSECURED 2: CALIBRATE 3: CAL COUNT 4: MESSAGEThe commands enclosed in square brackets ( ) are “hidden” unless the multimeteris UNSECURED for

9、calibration.1: 保护 1: 不保护 2: 校正 3: CAL 计数 4: 信息* 在正直的支架 () 的指令附件是 隐藏的 除非万用表为口径测定被不保护。Display Annunciators信号显示窗口*Turns on during a measurement在一个测量期间打开。AdrsMultimeter is addressed to listen or talk over the GPIB interface.万用表被从事于听或者讨论 GPIB通用接口总线的界面。RmtMultimeter is in remote mode (remote interface).万用

10、表在远程模式 （远程界面）中。ManMultimeter is using manual ranging (autorange is disabled).万用表正在手动修正（自动修正被禁止）。TrigMultimeter is waiting for a single trigger or external trigger.万用表正在等候一个触发或外部的触发。HoldReading Hold is enabled阅读锁被激活。MemTurns on when reading memory is enabled.等存储器被激活时开启。Ratio Multimeter is in dcv:dcv

11、ratio function.万用表正在执行检查，检查比率功能。Math A math operation is enabled (null, min-max, dB, dBm, or limit test).一个数学操作正在进行。ERROR Hardware or remote interface command errors are detected.检测到硬件或远程命令错误。RearRear input terminals are selected.背后输入终端被选择Shift“Shift” key has been “Shift” again to turnoff.Shift 键被按下，再按一下关闭4WMultimeter is in 4-wire ohms function.万用表在四线输入功能Multimeter is in continuity test function.万用表在连接测试功能Multimeter is in diode test function.万用表在二极管测试功能后面板一瞥ChassisGround1 外壳接地Power-LineFuse-HolderAssembly2 高压电线熔断丝装置Power-LineVoltageSetting3 高压电线电压设定FrontandRearCurrentInput