DEK印刷机操作编程

1、DEK操 作編 程操 作主画面的识別开关机调程序换钢网换顶针加锡膏安裝与清洗刮刀换钢网纸与酒精MARK识别操 作主画面的识别(1)主画面的识别(2)Mode印刷模式,有自动Auto,过板No Print,只刷一块板Single,手动Step,共四种.Product程式名PSS-INTERFACE-TOP Temperature温度Humidity相对湿度Cycle Time : 21.21 s :21.10 s其中21.21s为印刷上一块PCB所花的时间(不包括等板时间).Front Print Speed前印刷速度Rear Print Speed后印刷速度主画面的识别(3)Front Pre

2、ssure 前刮刀压力 Rear Pressure 后刮刀压力Separation Speed 分离速度Clean 1 Count Rate:1/2擦拭频率为每刷两块PCB擦一次钢网,現在已刷了一块.Print Direction 印刷方向,Reverse为向后印刷,Forward为向前印刷.开机將主电源开关順时针旋转90度至垂直位置.出現按亮系统键.Load DataDiagnost关机按Close SYSTEM按Yes出現Restart將主电源开关逆时针旋转90度至水平位置.调程序在主画面,按Setup按Load Data用Left,Right,Up,Down选择程序名按Load按Exit

3、 ,退回主菜单RunOpen CoverPaste LoadClean ScreenAdjustSetupmonitormaintLoadRebuild ListLeftRightUpDownExitModeLoad DataEdit DataSetup SqueegeeChange ScreenChange ToolingChange LanguageExitLoadRebuild ListLeftRightUpDownExitModeLoad DataEdit DataSetup SqueegeeChange ScreenChange ToolingChange languageExit取

4、出钢网按Open Cover按Change Screen出現Open Front Cover and Remove Screen打开前盖取出钢网关上前盖按亮系统键RunOpen CoverPaste LoadClean ScreenAdjustSetupmonitormaintCHANGE SCREENBOARD CLAMPSPRIME PAPERPRIME SOLVENTExit换上钢网按Open Cover打开前盖放入钢网盖上前盖按亮系统键按Change Screen按Exit ,退回主菜单RunOpen CoverPaste LoadClean ScreenAdjustSetupmoni

5、tormaintCHANGE SCREENBOARD CLAMPSPRIME PAPERPRIME SOLVENTExitCHANGE SCREENBOARD CLAMPSPRIME PAPERPRIME SOLVENTExit换顶针(1)在主画面,按Setup按Change Tooling按Open Cover打开前盖放入顶针放入钢网关上前盖按亮系统键RunOpen CoverPaste LoadClean ScreenAdjustSetupmonitormaintModeLoad DataEdit DataSetup SqueegeeChange ScreenChange ToolingC

6、hange LanguageExitAdjustOpen CoverHome CleanerBoard StopFull WidthLoad WidthPrint HeightExit换顶针(2)按Home Cleaner按Exit按Change Screen按Exit ,退回主菜单AdjustOpen CoverHome CleanerBoard StopFull WidthLoad WidthPrint HeightExitAdjustOpen CoverRemove CleanerBoard StopFull WidthLoad WidthPrint HeightExitModeLoad

7、 DataEdit DataSetup SqueegeeChange ScreenChange ToolingChange LanguageExitModeLoad DataEdit DataSetup SqueegeeChange ScreenChange ToolingChange LanguageExit加锡膏(1)按Paste Load按Manual Load出現open cover and load paste打開前盖加锡膏关上前盖按亮系统键RunOpen CoverPaste LoadClean ScreenAdjustSetupmonitormaintManual LoadPri

8、nt DirectnExit加锡膏(2)按Continue按Exit ,退回主菜单ContinueManual LoadPrint DirectnExit安裝与清洗刮刀在取出钢网的时候,松开固定刮刀的兩個螺丝即可取出刮刀.应松开锡膏挡片以对刮刀进行彻底清洁.旋紧螺丝时应注意避免螺丝滑丝.安裝刮刀时应保持两边平衡.轻拿轻放,避免损坏刮刀.换钢网纸(1)按Open Cover按Change Screen出現Open Front Cover and Remove Screen打开前盖取出钢网取出旧钢网纸裝好新钢网纸裝回钢网RunOpen CoverPaste LoadClean ScreenAdju

9、stSetupmonitormaintCHANGE SCREENBOARD CLAMPSPRIME PAPERPRIME SOLVENTExit换钢网纸(2)关上前盖按亮系统键按Change Screen按Exit,退回主菜单CHANGE SCREENBOARD CLAMPSPRIME PAPERPRIME SOLVENTExitCHANGE SCREENBOARD CLAMPSPRIME PAPERPRIME SOLVENTExit换酒精按Open Cover打开前盖松开溶剂盒的盖子加入酒精裝回溶剂盒的盖子关上前盖按亮系统键按Exit ,退回主菜单RunOpen CoverPaste Loa

10、dClean ScreenAdjustSetupmonitormaintCHANGE SCREENBOARD CLAMPSPRIME PAPERPRIME SOLVENTExit改变印刷模式在主画面,按Setup.按Mode,使主画面左上角的Mode在Auto,No Print,Single,Step中轮换.选好后,按Exit ,退回主菜单.RunOpen CoverPaste LoadClean ScreenAdjustSetupmonitormaintModeLoad DataEdit DataSetup SqueegeeChange ScreenChange ToolingChange

11、LanguageExitModeLoad DataEdit DataSetup SqueegeeChange ScreenChange ToolingChange LanguageExitMARK识别(1)將印刷模式选为Step.在主菜单中,按Run按Auto Board按Step按StepRunOpen CoverPaste LoadClean ScreenAdjustSetupmonitormaintAuto BoardManual BoardExitStepSingleExitStepSingleExitMARK识别(2)MARK识别(3)如果MARK点位置偏移较多,可按Adjust调整

12、MARK点坐标.如果画面上找不到识别点,可通过Search Step手动寻找识别点,直至找到为止.如果错过,可按Search Reset搜寻位置复位.如识别点位置尚可,则按Fiducial Setup,进入以下画面.StepOpen CoverFiducial SetupAdjustSearch StepSearch ResetSingleExitMARK识别(4)MARK识别(5)将MARK 点类型Fiducial Type调成相应的形状,圆形Circle,或方形Rectangle.將MARK背景Background调成相应的黑色Dark,或白色Light.将接受分数Accept Score

13、调成600.(当机器MARK点的分数小于该接受分数时将报警,不能印刷.该接受分数可根据实际情況下更改)按Learn Fiducial进入画面右上方编辑栏MARK尺寸.如MARK点为圆形,则尺寸为直径Diameter,如为方形,则尺寸宽Fiducial Width,高Fiducial Height.Learn FiducialLocate FiducialSet LightNextPreviousIncr.Decr.ExitMARK识别(6)调好后按Learn Fiducial按Exit按Locate Fiducial如分數符合要求,則按Exit.(否則須重新調整參數)按ExitLearn Fi

14、ducialNextPreviousIncr.Decr.ExitLearn FiducialNextPreviousIncr.Decr.ExitLearn FiducialLocate FiducialSet LightNextPreviousIncr.Decr.ExitLocate FiducialExitLearn FiducialLocate FiducialSet LightNextPreviousIncr.Decr.ExitMARK识别(7)按Step同理,重复之前设置MARK部分操作.将两个PCB识别点及其钢网识别点核对OK后,按Step.出现Saving Fiducial Dat

15、a-Please Wait Board data file saved,按Exit.StepOpen CoverFiducial SetupAdjustSearch StepSearch ResetSingleExitStepSingleExitStepOpen CoverFiducial SetupAdjustSearch StepSearch ResetSingleExitMARK识别(8)按Exit.Auto BoardManual BoardExit编 程编程(2)在主画面,按Setup.按Edit DataRunOpen CoverPaste LoadClean ScreenAdjustSetupmonitormaintModeLoad DataEdit DataSetup SqueegeeChange ScreenChange ToolingChange LanguageExit编程(3)编程(4)当光标置于PRODUCT NAME时按Incr.,键入新的程式名.按Yes输入以下参数的数值:BOARD WIDTHBOARD LENGTHBOARD THICKNESSSaveNextPreviousIncr.Decr.ExitYesGlobals OnlyNo编程(5)编程(6)FIDUCIAL 1 X第一个识别点的X坐标FIDUCIAL 1