量具重复性和再现性数据表

1、,量具重复性和再现性数据表,NO:,版号:,A,修订号:,1,表格编号, , ,量具名称: caliper,硬度计,基准件名称:,橡胶硬度块,测量日期: ,15.06.18,量具编号:,IES-G-018,测量参数:,硬度,测量人员:,A B C ,量具量程: 0-99,参数规格:,80-90,评价人数,3,零,件,编,号,个数:,10,平均值,试验次数,3,1,2,3,4,5,6,7,8,9,10,1.,A,1,85 ,84 ,84 ,83 ,84 ,84 ,84 ,83 ,85 ,84 ,84.0000,2.,2,84 ,84 ,84 ,83 ,84 ,85 ,84 ,83 ,85 ,84

2、 ,84.0000,3.,3,84 ,84 ,83 ,83 ,84 ,84 ,84 ,84 ,85 ,83 ,83.8000,4.,均值,84.333,84.000,83.667,83.000,84.000,84.333,84.000,83.333,85.000,83.667,83.93335., 极差,1.000,0.000,1.000,0.000,0.000,1.000,0.000,1.000,0.000,1.000,0.50006.,B,1,84 ,83 ,83 ,83 ,84 ,83 ,83 ,83 ,84 ,83 ,83.3000,7.,2,84 ,84 ,84 ,83 ,83 ,8

3、4 ,84 ,84 ,85 ,83 ,83.8000,8.,3,84 ,83 ,83 ,82 ,84 ,84 ,84 ,84 ,84 ,83 ,83.5000,9.,均值,84.000,83.333,83.333,82.667,83.667,83.667,83.667,83.667,84.333,83.000,83.533310., 极差,0.000,1.000,1.000,1.000,1.000,1.000,1.000,1.000,1.000,0.000,0.800011.,C,1,85 ,84 ,84 ,83 ,84 ,85 ,85 ,85 ,85 ,85 ,84.5000,12.,2,8

4、4 ,84 ,84 ,83 ,84 ,84 ,85 ,84 ,85 ,84 ,84.1000,13.,3,85 ,83 ,83 ,83 ,85 ,85 ,84 ,84 ,85 ,84 ,84.1000,14.,均值,84.667,83.667,83.667,83.000,84.333,84.667,84.667,84.333,85.000,84.333,84.233315., 极差,1.000,1.000,1.000,0.000,1.000,1.000,1.000,1.000,0.000,1.000,0.8000,零件均值,84.333,83.667,83.556,82.889,84.000,

5、84.222,84.111,83.778,84.778,83.667,83.9000,1.8889,极差均值,0.7,试验次数,2,3,最大均值差,0.7000,D4,3.27,2.57,均值上限,84.6140,极差上限,1.7990,D3,0,0,均值下限,83.1860,极差下限,0,A2,1.88,1.02注:,圈出那些超出控制限的值。查明原因並纠正。同一评价人采用最初的仪器重复这些读数或剔除这些值并由其余观测值再次平均,并计算R和极限值.,均值图,UCLx =,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,84.6140,LCLx =,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,83.1860,UCLR =,1.7990,1.7990,1.7990,1.7990,1.7990,1.7990,1.7990,1.7990,1.7990,