英国焊接标准

1、英国焊接标准英国焊接标准英国焊接标准(BS welding standards)ANSI | BS | DIN | EN | GB | ISO | JIS | NF |DIC编号中文名称英文名称BS 1722-10-2006栅栏.链节和焊接筛网的防 盗栅栏用规范Fences - Specification for anti-intruder fences in chain link and welded meshBS 1894-1992焊接结构的电热锅炉的设 计和制造规范Specification for design and manufacture of electric boilers o

2、f welded constructionBS 2790-1992焊接结构的壳式锅炉的设 计和制造规范Specification for design and manufacture of shell boilers of welded constructionBS 2S 510-1970碳钢薄板和带材规范（430/540 MPa）（适用于焊 接）Specification for carbon steel sheet and strip (430/540 MPa) (suitable for welding)BS 2S 511-1970深拉碳钢薄钢板和带材的规范（280/400 MPa）（适

3、用 于焊接）Specification for deep drawing carbon steel sheet and strip (280/400 MPa) (suitable for welding)BS 2S 514-1969碳钻钢薄板和带材规范（淬 火和回火条件:77/100MPa）（适用于焊 接）Specification for carbon-manganese steel sheet and strip (for use in the hardened and tempered condition: 770/1000 MPa) (suitable for welding)BS 2

4、S 515-1969碳钻钢薄板和带材规范（退 火的）（退火条件:46/59MPa）（适用于焊 接）Specification for carbon-manganese steel sheet and strip (softened) (for use in the softened condition: 460/600 MPa) (suitable for welding)BS 2s 92-1964飞机材料规范.碳钻钢（适 用于焊接）（40/55吨力/平 方英寸；限定等圆断面4英 寸）Specification for aircraft material - Carbon-manganese

5、steel (suitable for welding) (40/55 tonf/sq in: limiting ruling section 4 in)BS 2T 66-198019/10铭-锲耐腐蚀钢管材规范（花稳定的:550MPa）（可焊接）Specification for 18/10 chromium-nickel corrosion-resisting steel tube (niobium stabilized: 550 MPa) (weldable)BS 2T 68-1980冷拉18/10铭-锲耐腐蚀钢 管材规范（花稳定的:800MPa）（可焊接）Specification f

6、or cold drawn 18/10 chromium-nickel corrosion-resisting steel tube (niobium stabilized: 800 MPa) (weldable)BS 3604-2-1991承压钢管.具有规定高温特 性的铁合金钢.第2部分： 纵向电弧焊接管规范Steel pipes and tubes for pressure purposes: ferritic alloy steel with specified elevated temperature properties - Specification for longitudina

7、lly arc welded tubesBS 3799-1974石油工业用钢管配件、螺旋 管接头和套管焊接规范Specification for steel pipe fittings, screwed and socket-welding for the petroleum industryBS 3T 53-1980铭-铝钢管材规范（700MPa）（管外径不小于12.5mm）（可焊接）Specification for chromium-molybdenum steel tube (700 MPa) (outside diameter not less than 12.5 mm) (weld

8、able)BS 4129-1990板材钢电阻焊用焊接底剂、 焊透密封剂、粘合剂和蜡规 范Specification for welding primers and weld-through sealants, adhesives and waxes for resistance welding of sheet steelBS 4449-2005+A2-2 009混凝土增强钢.可焊接增强 钢.棒材、卷材和拆卷产品. 规范Steel for the reinforcement of concrete - Weldable reinforcing steel - Bar, coiland deco

9、iled product - SpecificationBS 4515-1-2009陆地和近海钢管焊接规范. 碳和碳钻钢管Specification for welding ofsteel pipelines on land andoffshorePart 1: Carbon and carbon manganesesteel pipelinesBS 4515-2-1999陆地和近海铺设的钢管焊 接规范.双联法不锈钢管道Specification for welding of steel pipelines on land and offshore - Duplex stainless ste

10、el pipelinesBS 4871-3-1985按认可焊接工艺操作的焊 工鉴定考试规范.第3部 分:金属管与管板接头间电 弧焊Specification for approval testing of welders working to approved welding procedures -Arc welding of tube to tube-plate joints in metallic materialsBS 4872-1-1982/、要求才匕准焊接程序的焊 工考试规范.第1部分：钢 熔焊Specification for approval testing of welder

11、s when welding procedure approval is not required - Fusion welding of steelBS 4872-2-1976/、要求才匕准焊接工艺时焊 工的鉴定考试规范.第2部 分：铝及铝合金鸨极惰性气 体保护电弧焊或熔化极惰 性气体保护Specification for approval testing of welders when welding procedure approval is not required - TIG or MIG welding of aluminium and its alloysBS 499-1 Sup

12、plement-199 2焊接术语与符号.补充.电 焊设备的定义Welding terms and symbols - Supplement - Definitions for electric welding equipmentBS 499-1-2009焊接术语和符号.焊接、钎 焊和热切割用术语表Welding terms and symbolsPart 1: Glossary for welding, brazing andthermal cuttingBS 499-2C-1999焊接术语与符号.图表形式 的的欧洲电弧焊符号Welding terms and symbols - Europ

13、ean arc welding symbols in chart formBS 4T 45-1972碳-钻钢管材规格（700 N/mm）（管外径大 于或等于12.5mm）（可焊 接）Specification for carbon-manganese steel tube (700 N/mm2) (tube 12.5 mm outside diameter and greater) (weldable)BS 5950-2-2001建筑物中结构用的钢制件. 材料、制造和装配规范.轧 制及焊接型材Structural use of steelwork in building - Specifica

14、tion for materials, fabrication and erection - Rolled and welded sectionsBS 5S 21-1964飞机材料规范.20号碳钢（适用于焊接）（25/35吨力/平方英寸：最大直径或最小断面尺寸6英寸）Specification for aircraft material - 20 carbon steel (suitable for welding) (25/35 tonf/sq in: maximum size 6 inches diameter or minor sectional dimension)BS 638-4-1

15、996电弧焊电源、设备和附件. 第4部分：焊接电缆规范Arc welding power sources, equipment and accessories - Specification for welding cablesBS 6942-2-1989氧燃料气体焊接和相关工 艺用成套小型工具的设计 和建造.第2部分：使用可 充氧气和燃气容器的成套 工具规范Design and construction of small kits for oxy-fuel gas welding and allied processes -Specification for kits using refil

16、lable gas containers for oxygen and fuel gasBS 6990-1989含有工艺流体或其残留物 的钢管焊接实用规程Code of practice for welding on steel pipes containing process fluids or their residualsBS 7122-1989液化气体道路运输用的焊 接钢樽车规范Specification for welded steel tanks for the road transport of liquefiable gasesBS 7363-1990焊接用受控热强度试验和 叠

17、珠焊缝板试验方法Method for bead-on-plate (BOP) test for weldsBS 7372-3-1993工业金属丝筛网和金属丝Guide to the choice of编织布孔径和丝径组合选 择指南.第3部分：预压接 或压力焊接金属丝筛网的 优选组合aperture size and wire diameter combinations for industrial wire screens and woven wire cloth - Preferred combinations for pre-crimped or pressure-welded wire

18、screensBS 7448-2-1997断裂机械韧性试验.第2部 分:金属材料焊接的 KDOWNIDOWNc临界 CTOD 值和临界J值的测定方法Fracture mechanics toughness tests - Method for determination of KIc, critical CTOD and critical J values of welds in metallic materialsBS7655-2.4-2000电缆用绝缘和铠装材料规 范.横向耦合弹性铠装化合 物.焊接电缆包敷物Specification for insulating and sheathin

19、g materials for cables - Cross-linked elastomeric sheathing compounds - Welding cable coveringBS 7670-2-1997电阻凸焊的钢螺母和螺栓. 焊接螺母和螺栓的焊接规 范Steel nuts and bolts for resistance projection welding - Specification for welding of weld nuts and weld boltsBS 8451-2004气焊切割和相关工艺用橡 胶软管.图度耐扭结重型焊 接软管（H型）.规范Rubber ho

20、ses for gas welding, cutting and allied processes -High kink-resistant heavy duty welding hose (type H)- SpecificationBS 855-1990集中供热和间接热水供应 用焊接钢锅炉（额定输出 44KWE 3MW）fi范Specification for welded steel boilers for central heating and indirect hot water supply (rated output 44 kW to 3 MW)BS 91-1998电缆焊接插座.

21、规范Electric cable soldering sockets - SpecificationBS 9210N0009-1-1978射频连接器（SMC系列）详 细规范.不密封、焊接、静 态接触、50 Q、螺纹连接.Detail specification for radio frequency connectors (series SMC) - Unsealed,BS 9210 N007-1-1976射频连接器（SMB型）的详 细规范.不密封、焊接、静 态接触、50Q、插入式连接.全面评定级Detail specification for radio frequency connecto

22、rs (type SMB) - Unsealed, soldered, captive contact, 50 $2I, snap-on couplings - Full assessment levelBS 9210 N007-2-1976射频连接器（SMB型）的详 细规范.不密封、焊接、静 态接触、50 Q、连接扣.控 制图.配合面详图和测量数 据Detail specification for radio frequency connectors (type SMB) - Unsealed, soldered, captive contact, 50 ohms, snap-on coup

23、lings - Control drawings - Mating face details and gauge informationBS 9612N016-1979振荡器用电阻焊接密封石 英晶体元件用详细规 范.DN、DZ DQ和DP外壳、 0.8 20MH却 3.0 30MHz 频率范围.宽温范Detail specification for resistance welded seal quartz crystal units for oscillator applications - DN, DZ, DQand DPenclosures, 0. 8 to 20 MHz and 3.0

24、 to 30 MHz frequency ranges - Fundamental thickness-shear mode, AT-cut, for operation全面评定级soldered, captive contact, 50 $2I, screw coupling - Full assessment levelBS 9210N0009-2-1978射频连接器（SMA系列）详 细规范.不密封、焊接、静 态接触、50 Q、螺纹连接. 控制图.配合面详图和测量 数据Detail specification for radio frequency connectors (series S

25、MC) - Unsealed, soldered, captive contact, 50 ohms, screw coupling - Control drawings - Mating face details and gauge informationBS 9210 N001-1-1975射频连接器（BNC型）的详 细规范.50。的密封、焊 接、静态接触.全面评定级Detail specification for radio frequency connectors (type BNC) - Sealed, soldered, captive contact, 50 ohms - Ful

26、l assessment levelover wide temperature ranges (non-temperature controlled) - Full assessment levelBS 9612N017-1979振荡器用电阻焊接密封石 英晶体元件用详细规 范.DN、DZ DQ和DP外壳、 0.8 20MH却 3.0 30MHz 频率范围.窄温范Detail specification for resistance welded seal quartz crystal units for oscillator applications - DN, DZ, DQand DPenc

27、losures, 0. 8 to 20 MHz and 3.0 to 30 MHz frequency ranges - Fundamental thickness-shear mode, AT-cut, for operation over narrow temperature ranges (temperature controlled) - Full assessment levelBSDDCENSO/TS15011-5-2006焊接和相关工艺的卫生和 安全.烟尘和气体取样的试 验室方法.通过完全或部分 有机材料组成的产品焊接 或切割时所Health and safety in weld

28、ing and allied processes - Laboratory method for sampling fume and gases - Identification of thermal-degradation products generated when welding or cutting through products composed wholly or partly of organic materialsBSDDCENSO/TS 17845-2004焊接和相关程序.缺陷的名 称与符号系统Welding and allied processes-Designatio

29、n system for imperfectionsBS DD CEN/TS 14751-2004焊接.焊接检验用飞行时间 衍射技术(TOFD)的使用Welding - Use of time-of-flight diffraction technique (TOFD) for examination of weldsBS DD ENV 10080-1996混凝土加强筋用钢.可焊肋 状钢筋B500.棒材、卷材和 焊接钢筋网的交付技术状 态Steel for the reinforcement of concrete - Weldable ribbed reinforcing steel B50

30、0 - Technical delivery conditions for bars, coils and welded fabricBS EN 10025-3-2004结构钢热轧制品.正火/正 火热机轧制的可焊接细粒 结构钢的交货技术条件Hot rolled products of structural steels - Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steelsBS EN 10025-4-2004结构钢热轧制品.热机轧制 的可焊接细粒

31、结构钢的交 货技术条件Hot rolled products of structural steels - Technical delivery conditions for thermomechanical rolled weldable fine grain structural steelsBS EN 10028-6-2009压力容器用钢制扁平产品. 可焊接淬火和回火细粒钢Flat products made of steels for pressure purposes - Part 6:Weldable fine grain steels, quenched and tempered

32、BS EN 10080-2005混凝土增强用钢.可焊接增 强钢.总则Steel for the reinforcement of concrete - Weldable reinforcing steel - GeneralBS EN 1011-1-2009焊接.金属材料焊接用推荐 规程.弧焊用一般指南Welding - Recommendations for welding of metallic materials - General guidance for arc weldingBS EN 1011-2-2001焊接.金属材料焊接的推荐 规范.铁素体钢的电弧焊接Welding - Re

33、commendations for welding of metallic materials - Arc welding of ferritic steelsBS EN 1011-3-2000焊接.金属材料焊接的推荐 规范.不锈钢的电弧焊接Welding - Recommendations for welding of metallic materials - Arc welding of stainless steelsBS EN 1011-4-2000焊接.金属材料焊接的推荐 规范.铝及铝合金的电弧焊 接Welding - Recommendations for welding of m

34、etallic materials - Arc welding of aluminium and aluminium alloysBS EN 1011-5-2003焊接.金属材料焊接的推荐 规程.覆层钢的焊接Welding - Recommendations for welding of metallic materials - Welding of clad steelBS EN 1011-6-2005焊接.金属材料焊接的建 议.第6部分：激光束焊接Welding - Recommendations for welding of metallic materials - Part 6: La

35、ser beam weldingBS EN 1011-7-2004焊接.金属材料焊接的推荐 规范.电子束焊Welding - Recommendations for welding of metallic materials - Electron beam weldingBS EN 1011-8-2004焊接.金属材料焊接的推荐 规范.铸铁的焊接Welding - Recommendations for welding of metallic materials - Welding of cast ironsBS EN 10120-2008焊接的储气瓶用钢薄板材 和带材Steel sheet

36、and strip for welded gas cylindersBS EN 10217-1-2002承压用焊接钢管.交付技术 状态.规定室温特性的非合 金钢管Welded steel tubes for pressure purposes - Technical delivery conditions - Non-alloy steel tubes with specified room temperature propertiesBS EN 10217-2-2002承压用的焊接钢管.交付技 术状态.规定r高温特性的 非合金和合金电焊钢管Welded steel tubes for pre

37、ssure purposes - Technical delivery conditions - Electric welded non-alloy and alloy steel tubes with specified elevated temperature propertiesBS EN 10217-3-2002承压用的焊接钢管.交付技 术状态.合金细晶粒钢管Welded steel tubes for pressure purposes - Technical delivery conditions - Alloy fine grain steel tubesBS EN承压用的焊接钢

38、管.交付技Welded steel tubes for10217-4-2002术状态.规定了低温特性的 非合金和合金电焊钢管pressure purposes - Technical delivery conditions - Electric welded non-alloy steel tubes with specified low temperature propertiesBS EN 10217-5-2002承压用的焊接钢管.交付技 术状态.规定r高温特性的 非合金和合金埋弧焊接钢 管Welded steel tubes for pressure purposes - Technic

39、al delivery conditions - Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature propertiesBS EN 10217-6-2002承压用的焊接钢管.交付技 术条件.规定r低温特性的 非合金埋弧焊接钢管Welded steel tubes for pressure purposes - Technical delivery conditions - Submerged arc welded non-alloy steel tubes with

40、specified low temperature propertiesBS EN 10217-7-2005压力用途焊接钢管.交货技 术条件.不锈钢管Welded steel tubes for pressure purposes - Technical delivery conditions - Stainless steel tubesBS EN 10219-1-2006非合金和细晶结构钢的冷 成形焊接结构空心型材.交 货技术要求Cold formed welded structural hollow sections of non-alloy and fine grain steels

41、- Technical delivery requirementsBS EN 10219-2-2006非合金和细晶结构钢的冷 成形焊接结构空心型材.公 差、尺寸和局部特性Cold formed welded structural hollow sections of non-alloy and fine grain steels - Tolerances, dimensions and sectional propertiesBS EN 10220-2002无缝和焊接钢管.尺寸和每 单位长度的质量Seamless and welded steel tubes - Dimensions and

42、massesper unit lengthBS EN 10222-4-1999压力容器用钢锻件.具启高 验收强度的可焊接细晶粒 钢Steel forgings for pressure purposes - Weldable fine-grain steels with high proof strengthBS EN 10223-4-1998栅栏用钢丝和钢丝制品.钢 丝焊接网式栅栏Steel wire and wire products for fences - Steel wire welded mesh fencingBS EN 10223-7-2002栏栅用钢丝和金属丝制品. 栏栅用钢

43、丝焊接网板Steel wire and wire products for fences - Steel wire welded panels - For fencingBS EN 10225-2009固定近海结构的可焊接结 构钢.技术提交条件Weldable structural steels for fixed offshore structures - Technical delivery conditionsBS EN 10246-1-1996钢管的无损检验.证明液压 系统密封性用无缝和焊接 铁磁钢管（埋弧焊除外）的 自动电磁检验Non-destructive testing of s

44、teel tubes - Automatic electromagnetic testing of seamless and welded (except submerged arc welded) ferromagnetic steel tubes for verification of hydraulic leak-tightnessBS EN 10246-11-2000钢管的无损检验.对无缝和 焊接钢管进行液体渗透试 验以检测其表面缺陷Non-destructive testing of steel tubes - Liquid penetrant testing of seamless

45、 and welded steel tubes for the detection of surface imperfectionsBS EN 10246-12-2000钢管的无损检验.对无缝和 焊接铁磁钢管进行磁粉检 验以检测其表面缺陷Non-destructive testing of steel tubes - Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfectionsBS EN 10246-13-2000钢

46、管的无损检验.无缝和焊 接钢管（埋弧焊除外）的全Non-destructive testing of steel tubes - Automatic full外围自动超声波厚度检测peripheral ultrasonic thickness testing for seamless and welded (except submerged arc welded) steel tubesBS EN 10246-14-2000钢管的无损检验.层状缺陷 探测用无缝和焊接（埋弧焊 接除外）钢管的自动超声波 检验Non-destructive testing of steel tubes - Auto

47、matic ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of laminar imperfectionsBS EN 10246-15-2000钢管的无损检验.无缝和焊 接钢管（埋弧焊除外）的全 外围自动超声波厚度检测Non-destructive testing of steel tubes - Automatic ultrasonic testing of strip/plate used in the manufacture of

48、welded steel tubes for the detection of laminar imperfectionsBS EN 10246-16-2000钢管的无损检验.对焊接钢 管焊缝临近区域进行自动 超声波检验以检测其层状 缺陷Non-destructive testing of steel tubes - Automatic ultrasonic testing of the area adjacent to the weld seam of welded steel tubes for the detection of laminar imperfectionsBS EN 102

49、46-17-2000钢管的无损检验.对无缝和 焊接钢管管端部进行超声 波检验以检测其层状缺陷Non-destructive testing of steel tubes - Ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfectionsBS EN 10246-18-2000钢管的无损检验.对无缝和 焊接铁磁钢管管端部进行 磁粉检验以检测其层状缺 陷Non-destructive testing of steel tubes - Magnet

50、ic particle inspection of tube ends of seamless and welded ferromagnetic steel tubes for the detection of laminar imperfectionsBS EN 10246-2-2000钢管的无损检验.验证水密 封性能用的无缝和焊接的 （埋弧焊除外）奥氏体铁素 体钢管的自动涡流试验Non-destructive testing of steel tubes - Automatic eddy current testing of seamless and welded (except subm

51、erged arc welded) austenitic and austenitic-ferritic steel tubes for verification of hydraulic leak-tightnessBS EN 10246-3-2000钢管的无损检验.缺陷探测 用无缝和焊接（埋弧焊除 外）钢管的自动涡流检验Non-destructive testing of steel tubes - Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes

52、for the detection of imperfectionsBS EN 10246-5-2000钢管的无损检验.纵向缺陷 探测用无缝和焊接（埋弧焊 除外）的铁磁性钢管的自动 全周界磁力换能器/磁力线 渗漏检验Non-destructive testing of steel tubes - Automatic full peripheral magnetic transducer/flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for t

53、he detection of longitudinal imperfectionsBS EN 10246-7-2005钢管的无损检验.纵向缺陷 探测用无缝焊接钢管（埋弧 焊除外）的自动全周界超声 波检验Non-destructive testing of steel tubes - Part 7: Automatic full peripheral ultrasonic testing of seamless and welded (except submerged arc welded) tubes for the detection of longitudinal imperfectio

54、nsBS EN 10246-9-2000钢管的无损检验.检测纵向 或横向缺陷用的焊接和埋 弧焊钢管的自动超声波试 验Non-destructive testing of steel tubes - Automatic ultrasonic testing of the weld seam of submerged arc welded steel tubes for the detection of longitudinal and/or transverse imperfectionsBS EN 10255-2004焊接或加螺纹的非合金钢 管.交货技术条件Non-alloy steel tu

55、bes suitable for welding and threading - Technical delivery conditionsBS EN 10296-1-2003机械和一般工程用焊接圆 钢管.技术交货条件.非合 金和合金钢管Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Non-alloy and alloy steel tubesBS EN 10296-2-2005机械和一般工程用焊接圆 钢管.技术交货条件.

56、不锈 钢Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Stainless steelBS EN 10305-2-2010精密仪器用钢管.交货技术 条件.焊接冷拔钢管Steel tubes for precision applications - Technical delivery conditions - Welded cold drawn tubesBS EN 10305-3-2010精密仪器用钢管.交货技术 条件.焊

57、接冷精加工钢管Steel tubes for precision applications - Technical delivery conditions - Welded cold sized tubesBS EN 10305-5-2010精密设备用钢管.交货技术 条件.焊接和冷精加工的方 形及矩形钢管Steel tubes for precision applications - Technical delivery conditions - Welded and cold sized square and rectangular tubesBS EN 10305-6-2005精密仪器用钢

58、管.交货技术 条件.第6部分：液压和气 动动力系统用焊接冷拉管 材Steel tubes forprecisionapplications Technicaldeliveryconditions Part 6: Welded cold drawn tubes forhydraulic and pneumatic powersystemsBS EN 10312-2003包括人生活用水在内的水 成液输送用焊接/、锈钢管. 交货技术条件Welded stainless steel tubes for the conveyance of aqueous liquids inclu ding water

59、 for human consumption -Technical delivery conditionsBS EN 1043-1-1996金属材料焊接的破坏试验. 硬度试验.第1部分：电弧 焊接的硬度试验Destructive tests on welds in metallic materials -Hardness testing - Hardness test on arc welded jointsBS EN 1043-2-1997金属材料焊接点的破坏试 验.第2部分：焊接连接件 的显微硬度试验Destructive tests on welds in metallic materi

60、als -Hardness testing - Micro hardness testing on welded jointsBS EN 1123-1-1999污水系统用插接管的纵向 焊接热浸镀锌钢管及配件. 要求、试验和质量控制Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Requirements, testing, quality controlBS EN 1123-2-2006+A1 -2