Agilent34401A产品使用手册

1、WORD格式The Agilent Technologies 34401A is a 6 1/2-digit, high-performance digital multimeter. Its combination of bench-top and system features makes this multimeter a versatile solution for your measurement needs now and in the future.Agilent科技 34401 A是一 6 1/2数字的 ,高精度高性能数字万用表。它的长椅子的组合- 顶端和系统特征为你的测量需要

2、使这一个万用表成为用途广泛的解决现在和未来。Convenient Bench-Top FeaturesHighly visible vacuum-fluorescent displayBuilt-in math operationsContinuity and diode test functionsHands-free, Reading Hold featurePortable, ruggedized case with non-skid feet方便的长椅子- 顶端扮演重要角色? 高度地看得见的真空 - 日光灯展览? 内建的数学行动? 连续性和两极管测试功能? 免动手的 , 读把握特征?

3、手提式的 , 用非橇的脚使情形稳固了Flexible System FeaturesGPIB (IEEE-488) interface and RS-232 interfaceStandard programming languages: SCPI, Agilent 3478A, and Fluke 8840Reading rates up to 1000 readings per secondStorage for up to 512 readingsLimit testing with pass/fail signalsOptional 34812A BenchLink/Meter Sof

4、tware for Microsoft " WindowsTM灵活的系统作用" GPIB(IEEE-488)接口和 RS-232 接口" 标准程序语言 : SCPI， Agilent 3478 A,和Fluke8840? 阅读评估每秒达 1000 阅读? 储藏为达 512 阅读? 以途径 / 不及格尝试的界限向? 可选择的 34812 BenchLink/ 公尺软件为微软 "WindowsTMThe Front Panel at a Glance专业资料整理WORD格式前面板一瞥1 Measurement Function keys2 Math Oper

5、ation keys3 Single Trigger / Autotrigger / Reading Hold key4 Shift / Local key5 Front / Rear Input Terminal Switch6 Range / Number of Digits Displayed keys7 Menu Operation keys1 测量功能键2 数学操作键3信号触发 / Autotrigger触发 /阅读保持键4转换 /恢复键5前面的 / 后面的输入终端转换键6X围 /数字宽度显示键7 主菜单操作键The Front-Panel Menu at a GlanceThe m

6、enu is organized in a top-down tree structure with three levels前面板菜单一瞥菜单在由上而下的树构造被三个水平所组织A: MEASurement MENUA: 测量菜单1: AC FILTER >2: CONTINUITY >3: INPUT R >4: RATIO FUNC >5: RESOLUTION1: AC 过滤器 >2:连续性 >3:输入 R>4:比 FUNC>5: 决议B: MATH MENUB: 数学菜单1: MIN-MAX >2: NULL VALUE >3

7、: dB REL > 4: dBm REF R >5: LIMIT TEST >6: HIGH LIMIT >7: LOW LIMIT1:最小 - 最大 >2:无效的值>3:分贝损耗率>4: dBm参考 R>5:极限测试>6:最高界限 >7:低的界限C: TRIGger MENUC: 触发菜单1: READ HOLD >2: TRIG DELAY >3: N SAMPLES 1:阅读保持>2:追踪延迟>3: N抽样D: SYStem MENUD: 系统菜单1: RDGS STORE >2: SAVED R

8、DGS >3: ERROR >4: TEST > 5: DISPLAY >6: BEEP > 7: COMMA >8: REVISION1: RDGS 存贮 >2: 保存 RDGS>3: 错误 >4:测试 >5:演示 >6: 声音 >7:逗点 >8:修订E: Input / Output MENUE: 输入 / 输出菜单1: HP-IB ADDR >2: INTERFACE >3: BAUD RATE >4: PARITY > 5: LANGUAGE1: HP-IB的 ADDR>2: 接

9、口 >3:波特率 >4:奇偶 >5:语言F: CALibration MENU*F: 刻度菜单 *1: SECURED > 1: UNSECURED > 2: CALIBRATE >3: CAL COUNT >4: MESSAGE专业资料整理WORD格式The commands enclosed in square brackets ( ) are“hiddenunless the multimeteris UNSECURED for calibration.专业资料整理WORD格式1:保护 >1:不保护 >2:校正 >3: CAL计

10、数 >4:信息* 在正直的支架 ()的指令附件是 " 隐藏的 " 除非万用表为口径测定被不保护。Display Annunciators信号显示窗口* Turns on during a measurement在一个测量期间翻开。AdrsMultimeter is addressed to listen or talk over the GPIB interface.万用表被从事于听或者讨论GPIB通用接口总线的界面。RmtMultimeter is in remote mode (remote interface).万用表在远程模式远程界面中。ManMultimet

11、er is using manual ranging (autorange is disabled).万用表正在手动修正自动修正被制止。TrigMultimeter is waiting for a single trigger or external trigger.万用表正在等候一个触发或外部的触发。HoldReading Hold is enabled阅读锁被激活。MemTurns on when reading memory is enabled.等存储器被激活时开启。RatioMultimeter is in dcv:dcv ratio function.万用表正在执行检查，检查比率

12、功能。MathA math operation is enabled (null, min-max, dB, dBm, or limit test).一个数学操作正在进展。ERROR Hardware or remote interface command errors are detected.检测到硬件或远程命令错误。RearRear input terminals are selected.背后输入终端被选择Shift“Shiftkeyshabeen pressed.Press“Shiftagain to turn off.Shift键被按下，再按一下关闭4WMultimeter is

13、in 4-wire ohms function.专业资料整理WORD格式万用表在四线输入功能Multimeter is in continuity test function.万用表在连接测试功能Multimeter is in diode test function.万用表在二极管测试功能后面板一瞥1 Chassis Ground2 Power-Line Fuse-Holder Assembly3 Power-Line Voltage Setting4 Front and Rear Current Input Fuse5 Voltmeter Complete Output Terminal6 Exte