版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、道依茨发动机短发件装配流程参考标准Short Block Assembly Process ProductionAfter cleaning the engine assembly stand, hang the short block up, connect the engine assembly stand by fasten screws , 发动机装配平台擦拭干净后,升起短发件,螺栓拧紧使其固定于装 配平台,Short Block Assembly Process ProductionPut the sealant around the edge of the front cover,
2、 mount the front cover 在前机盖涂抹密封硅胶,安装前机盖,Short Block Assembly Process ProductionMount crankshaft toothed wheel and flange in order,tighten the central screw 按照顺序依次装配曲轴齿形皮带轮和凸缘,拧紧中央螺栓Short Block Assembly Process ProductionMount the camshaft toothed belt wheel, Pre -tighten the central screw, in order
3、to leave space for toothed belt adjustment 凸轮轴端安装齿形皮带轮,预紧螺栓,为齿形带调整预留空间Short Block Assembly Process Production5. Turn the engine assembly stand, , mount the oil pump, fasten the screws, 旋转装配台,安装机油泵,用扭矩扳手拧紧螺栓,Short Block Assembly Process ProductionMount the toothed belt and tensioning pulley ,press te
4、nsioning pulley against the toothed belt and align the toothed belt, fasten the screw . 安装齿形带和皮带张紧轮,张紧齿形带,拧紧螺栓Short Block Assembly Process Production7. Tighten the central screw,then make timing adjustment. 拧紧中央螺栓,进行正时调整,Short Block Assembly Process Production 8. Turn the short block 90,mount the hy
5、draulic stand, select the right shim, mount and tighten the single pump. 旋转发动机90,安装液压挺柱,旋转凸轮轴,选取正确的调整垫片,安装单体 泵,Short Block Assembly Process Production9. Fasten the screws of transfer nipple and oil pressure regulating valve. 用力矩扳手拧紧机油压力调节阀暖风堵塞增压调节阀,Short Block Assembly Process Production10. Mount fu
6、el filter console lube oil console and fuel pump,tighten the screws 安装机滤柴滤支架及手油泵,拧紧螺栓,Short Block Assembly Process Production11. Mount oil pressure line fuel supply line and overcurrent line,tighten the hollow screws 安装机油管、燃油管、燃油回油管,拧紧空心螺栓,Short Block Assembly Process Production12. Mount injection v
7、alves and fuel supply lines to injection valve,tighten screws and union nuts. 安装喷油嘴及高压油管,拧紧螺栓及联管螺母,Short Block Assembly Process Production13. Mount valve rods and toggle lever blocks,tighten screws and set valve clearance. 安装气门挺杆及气门摇臂,拧紧螺栓调节气门间隙,Short Block Assembly Process Production14. Mount fuel
8、filter on fuel filter console and oil filter on oil filter console, hand tight. 安装机油滤清器及柴油滤清器,手动拧紧即可,Short Block Assembly Process Production15. Put the sealant around the edge of oil intake pipe, tighten the screws. 集虑器边缘涂胶,用扭矩扳手拧紧螺栓,Short Block Assembly Process Production16. Put the sealant around
9、the edge of the oil pan, mount and tighten the screws. 使用密封硅胶均匀的涂抹油底壳边缘,安装拧紧油底壳螺栓,Short Block Assembly Process Production17. Mount the protective hood 、centrifugal disc 、V-belt pulley and generator,press V-belt pulley against V-belt, tighten the screws 安装保护盖离心盘V型皮带轮发电机,张紧V型皮带,拧紧螺栓,Short Block Assembly Process Production18.Mount exhaust manifold 、 turbocharger、 starte
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 2024年硅铁合金合作协议书
- 2024年悬浮床加氢裂化催化剂项目发展计划
- 2024年Α-乙酰乳酸脱羧酶项目发展计划
- 2024年智能电能表合作协议书
- 山东省菏泽外国语学校2024年六年级数学第一学期期末考试模拟试题含解析
- 山东省济南市商河县2024年六年级数学第一学期期末质量跟踪监视试题含解析
- 山东省济宁市鱼台县2024-2025学年六上数学期末质量检测模拟试题含解析
- 山东省临沂市河东区2024年数学四上期末检测模拟试题含解析
- 山东省青岛市城阳区2024年数学六上期末联考试题含解析
- 山东省日照市2024-2025学年数学六上期末学业水平测试模拟试题含解析
- 医院制剂成果转化方案
- 质量管理学第7章卓越绩效模式
- 培优第一讲数轴上的动点问题华东师大版七年级数学上册
- 部编版语文五年级上册第三单元【集体备课】
- 《食品卫生与安全》N亚硝基化合物安全案例
- 几丁聚糖资料
- 数学模型的课程设计-赛跑的速度
- 砂型铸造工艺设计说明书书
- 有限空间作业安全责任协议书
- 山西吕梁临县民俗文化
- 5G核心网技术职业技能培训考试
评论
0/150
提交评论