出口模制作DFM报告流程

1、Side Gate 侧水口侧水口Pin Point Gate 细水口细水口Hot Runner (Valve) 热流道针阀式热流道针阀式 Submarine Gate 潜水口潜水口Tab Gate 搭底水口搭底水口Hot Runner (Pin Point) With One Drop 热流道点进胶热流道点进胶Hot Sprue 单咀热流道单咀热流道Hot Runner (Direct) Turn To Submarine Gate 热流道转潜水口热流道转潜水口Hot Runner (Direct) Turn To Banana Gate 热流道转蕉形水口热流道转蕉形水口Hot Runner

2、(Direct )热流道热流道直浇口直浇口4mmCAVCORP/LBefore Change更改前更改前After Change更改后更改后 The height of the green surface : (Cut material for draft angle)绿色面减胶做出模斜度时参考如下标准:高度 减胶做2 度出模斜度；减胶高度 3.06.0mm减胶做1 度出模斜度；减胶高度 6.015.0mm减胶做度出模斜度；减胶高度15.0mm减胶做度出模斜度；减胶This green area is 0 degree, suggest to Cut material on the cavit

3、y to draft1 degree.绿色面无出模斜度，建议产品减胶1度做前模出模斜度Submarine Gate With 2Points2点潜水进胶Can you accept gate cushion?水口加工余留量是否接受水口加工余留量是否接受?Add Plastic 加胶Reduce Plastic减胶Cavity Inserts前模镶件Core Inserts后模镶件Undercut here, suggest to change as picture show.此处倒扣，建议如图更改EJ-Pins顶针Lifters斜顶Sliders行位Cavity Cooling 8mm前模运水

4、 8mmCore Cooling 8mm后模运水 8mmThis position need to make the inserts, but it will have the sharp steel, so we suggest to change the part.此处由于需要做前后模相插钢料太薄建议修改产品如下图所示！Undercut on red area, so here cannot be released by lifter, suggest to cancel the red feature.红色面倒扣，无法用斜顶行出，建议取消The wall of plastic is to

5、o thick here, suggest to reduce plastic to improve.此处胶位太厚，建议减胶IN 1OUT 1IN 2OUT 2IN 3OUT 3IN 4OUT 4IN 5OUT 5IN 6OUT 6IN 7OUT 7IN 8OUT 8IN 9OUT 9IN 10OUT 10IN 11OUT 11IN 12OUT 12IN 13OUT 13IN 14OUT 14IN 15OUT 15IN 16OUT 16IN 17OUT 17IN 18OUT 19IN 20OUT 20IN 21OUT 21IN 22OUT 22IN 23OUT 23Customer ( (客户

6、客户):):UNV1Model ( (型号型号):):DPCA B73 (100906)Part Name ( (产品名称产品名称):):Button ( (按钮）按钮） Part No. ( (产品编号产品编号):):A2C53347358/A2C53347355Drawing No. ( (图纸编号图纸编号):):40325705 DRW 000 AE / 40325711 DRW 000 AFMaterial ( (材料名称材料名称):):ABS-PC/SN 57906-11 BlackShrinkage ( (缩水率缩水率):):Mold Type ( (2/3板模板模):):2 Pl

7、ateGate Type ( (入水方式入水方式):):Submarine Gate 潜水进胶潜水进胶Injection Machine ( (注塑机台注塑机台):):50TCavity No. ( (出模数出模数):):1+1Design ( (编制编制):):胡伟庆胡伟庆Original Date ( (制定日期制定日期):):DFM Version ( (DFM版本版本):):A4Bill Of Material:Cavity: 2343ESR 5052 HRC Core: 2343ESR 5052HRC Slider: 2343ESR 5052HRC 3 3Material Shrin

8、kage一、排位及进胶 Layout And Inlet 4 4Material Shrinkage二、P/L 位置 P/L Position 5 5Material Shrinkage三、模具结构 前模 Mold Structure Cavity 6 6Material Shrinkage四、模具结构 后模 Mold Structure Core 7 7Material Shrinkage四、模具结构 A 顶出 Mold Structure A Ejector System 8 8Material Shrinkage五、前模运水 Cavity Cooling 9 9Material Shrinkage六、后模运水 Core Cooling 1010Material Shrinkage七、晒字位置 Engraved Position 1111Material Shrinkage八、蚀纹区域 Textured Area 1212Material Shr