卡莱特发送卡设置步骤(The T7 Send Card)

1、发送卡-T7卡莱特同步发送卡T7，是一款专业用于LED同步显示的发送卡，他具有分辨率自适应的功能，一张T7发送卡可控制130万点的LED显示屏（列数最大2048点，行数最大1024点），如超过可级联发送卡。配合DVI接口或者HDMI接口的独立显卡来使用。本文重点讲述设置发送卡的步骤。一、 发送卡连接图发送卡连接拓扑图（01）二、 硬件结构发送卡端口定义图（02）1. 供电（5V/2A）w 方法一：通过PCI供电：将T7发送卡的金手指插入电脑空的PCI插槽内；w 方法二：外接5V电源到T7发送卡的大4Pin电源插座上。发送卡红色指示灯常亮表示5V电供电正常。2. 连线w 用DVI线把T7发送卡与

2、显卡连接在一起，用于传输图像数据；w 用USB串口线将T7发送卡串口与电脑USB口相连，用于设置发送卡的程序；（注：首次需要安装串口驱动，可以在安装好卡莱特LED控制系统软件：LEDShowT9或LEDVISION后，在安装目录下找到“PL-2303 Driver Installer.exe”并安装这个文件）w 用网线将T7发送卡与接收卡相连，用于控制接收卡及大屏。（注：发送卡到接收卡以及接收卡之间的连接线为超五类或者六类的网线，水晶头的压制为国标568B的线序；）三、 显卡设置1显卡型号目前市场上主流的显卡有二大系列：NVIDIA的MX系列（400、440、5200等型号）；ATI的镭(RA

3、DEON)系列（4670、5550、7000、7500、8500、9000等型号）。正确安装相对应的显卡驱动。2设置NVIDIA显卡1) 首先我们要打开显卡设置界面：右键电脑桌面空白处，在如下图的菜单中选择【NVIDIA控制面板】：如果如下图所示没有【NVIDIA控制面板】，我们也可以点击【属性】,在【显示属性】对话框，点击【设置】，选择合适的显示器分辨率，再点击【高级】按钮，如下图所示：然后在弹出如下图的界面中，点击“GeForce”在如下图的界面中点击【启用NVIDIA控制面板】，也可以打开显卡设置的界面2) 在【NVIDIA控制面板】中选择【设置多个显示器】，再选择【复制模式】，点击【应

4、用】按钮即可。3 设置ATI显卡1) 首先要打开显卡设置界面，其操作方式与打开 NVIDIA设置界面雷同。2) 在如下图的ATI控制面板中，选择【显示器管理器】，右击模拟显示器2，点击【启用】，选择【复制模式】，点击【应用】，【确定】。 3) 出现如下图的界面即可点击【确定】，完成ATI的显卡设置。四、 设置发送卡参数1、控制界面打开卡莱特控制系统软件，点击【控制屏幕】-【屏幕管理】，选择【发送卡发送】，密码【168】，如下图【屏幕管理】界面。2、发送卡分辨率设置点击【分辨率设置】，发送卡默认分辨率为1280x1024，9.9版本的支持自适应分辨率，可以点击【设置为当前显示器的分辨率】，也可在

5、【发送卡分辨率】的下拉菜单中选择与当前显示器一样的分辨率点击【设置】如图所示。点击【设置】或者【设置为当前显示器的分辨率】后，会出现如下图所示的进度界面。发送完成后，软件会提示【发送成功，请断电重启发送卡！】，注：发送卡断电重启后，需再次进行本文第三节的显卡设置步骤。3、串口选择用USB串口线将T7发送卡串口与电脑USB口相连，用于设置发送卡的程序，当串口通信正常时，软件的屏幕管理界面串口状态会出现如下图所示【找到发送卡，可以设定参数】。（注：首次需要安装串口驱动，可以在安装好卡莱特LED控制系统软件：LEDShowT9或LEDVISION后，在安装目录下找到“PL-2303 Driver I

6、nstaller.exe”并安装这个文件）4、探测接收卡用来检测接收卡能否正常通讯（或观察接收卡绿灯有没快闪）。若是探测不到接收卡或者所探测出的接收卡的数量与实际不符，请检查接收卡是否已正常通电或网线是否接触良好。正确的操作如下图所示：5、网口控制面积设置根据LED显示屏的大小选择网口控制面积如图（a），然后【发送】到发送卡。若显示屏比较大，需要使用双网口，可以使用自定义模式，例如显示屏（1344*672），设置网口如图（b），然后【发送】到发送卡。（a） （b）网口控制面积设置以上为设置发送卡T7的全部步骤！The T7 Send CardColorlight synchronou

7、s send cards - T7, is a professional send card for LED synchronized display, with the function of adapting resolution automatically.  One T7 send card can control the LED display with 1.3 million pixel(maximum columns is 2048points, maximum 

8、;lines is 1024 points), if over the maximum, the send cards can be cascaded，and used with DVI or HDMI graphics card. This article focuses on the steps of setting send cards.一、 Connection Diagrams of Send Cardtopological connection diagrams of send card二、Hardware structureSend car

9、d port defined1.Power supply( 5V/2A)w Method 1: Supplied by PCI : put the T7 send cards goldfinger into the empty PCI slot of the computer;w Method 2: Connect 5V external power supply to the bigger 4-PIN power Socket on the T7 sen

10、d card.The red indicating lamp on the sending card work steadily, indicates the 5V power supply works well.2.connectionw Connect T7 send card with graphics card, by a DVI cable, for transmitting image dataConnect T7 send card serial port with the computers serial port, by a USB serial cable, fo

11、r setting program to the send card.w （Note: for the first time, need to install the serial driver. After install the Colorlight LED control system software: LEDShowT9 or LEDVISION, the "PL-2303 Driver Installer.exe" can be found in installation directory and install this file）w Connect T7

12、send card with receive card, by a network cable, for controlling the receive card and the screen（Note: the connecting cables between send cards and receive card, and the cables among receive cards are UTP cable or category six cable, the network cable plug comply with the line order of 568B internat

13、ional standard）三、Graphics card settings1.Graphics card modelCurrently, there are two mainstream graphics cards series on the market:NVIDIA's MX Series (model 400, 440, 5200 etc.ATI's RADEON Series (Model 4670, 5550, 7000,7500,8500,9000 etc.)Install the corresponding graphics card driver corr

14、ectly.2.ATI graphics card settings1)First, we open the graphics card setting interface: Right-click the space on desktop, select ATI Control Panel in the menu, just as the following image showsIf there is no ATI control panel in the menu, we can also click on Properties, as the following imageIn the

15、 Display Properties dialog box, click the Setting, select the appropriate display resolution, and then click Advanced button, as shown below:Then, click the ATI . in the interface, as following shown In the interface, click the ATI Catalyst Control Center as following image shows, also can open the

16、graphics card settings interfaceIn the ATI control panel, select Monitors Manager, as following image shows, then right-click simulate monitor 2, click Enable, select Copy Mode, and click Application, OK.The interface as shown in below image appears, click OK to finish the ATI graphics card setting.

17、3.(NVIDIA graphics card settings)1)First, open the graphics card setting interface, and its operation is similar to opening ATI setting interface2) In the NVIDIA Control Panel, select set up multiple monitors, and then select Copy Mode, click Application button.四、Set send cards parameters1.Control i

18、nterfaceOpen Colorlight control system software, click Control screen - Management screen, select the Send card send, passwords, 168, just as the following image of Management screen interfaceAuto COM SelectionNet Port Control Area SettingDetect Receiving cardSet Send Card ResolutionSet Display Area

19、 Location and SizeLoad or Edit Configuration Parameters2、send card resolution setting Click resolution settingSend cards default resolution is 1280x1024, 9.9 version send card support the function of adapting resolution automatically., click set to the current display resolution, also can select the

20、 same resolution to current display, in the drop-down menu of send card resolution and click set, just as following image shows.After click set or set to the current display resolution, it will appear the progressing interface, as show belowAfter the transmission, the software will prompt send succe

21、ssfully, please power off the send card, and restart! Note: After restart the send card, need to do the steps of graphics card setting again, in Chapter III of this article3. Serial ports choiceConnect T7 send card serial port with the computers serial port, by a USB serial cable, for setting t

22、he program to the send card. When the serial ports communicates well, the status of serial port, in the softwares management interface, will be just as below image shown found to send cards, can set parameters （Note: For the first time, need to install the serial driver

23、. After install the Colorlight LED control system software: LEDShowT9 or LEDVISION, the "PL-2303 Driver Installer.exe" can be found in installation directory and install this file）4. Detecting receive cardFor testing whether the receive card communicate well (or observe whether the green lamp on receive card flash quickly). If detect no receive card,&