某省电信汇聚交换机OLT双上行配置模板

1 汇聚交换机 OLT 双上行配置 模板 V2 华为 S8505 模式一：单链路 +Smar-link 1. 板卡硬件要求： 要求板卡中带有“ DB”字样并且软件版本在 1267 以上、或者没有“ DB”字样软件版本在 1628 以上，可以支持灵活 QinQ 。 2. 软件版本要求： Release1600 以上可以配 Smart-link 3. 配置命令 定义 VLAN ACL acl number 4001 rule 0 permit ingress 51 to 1050 egress any /匹配普通宽带拨号用户 VLAN rule 1 permit ingress 43 egress any /匹配 iTV 用户 VLAN rule 2 permit ingress 45 egress any /匹配 ITMS 终端管理 VLAN 定义外层 VLAN vlan 501-502 901-902 1701-1702 smart-link 配置 stp region-configuration instance 1 vlan 501 901 1701 instance 2 vlan 502 902 1702 active region-configuration /每次更改配置后必须执行这条命令才生效 smart-link group 1 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance 1 undo flush enable smart-link group 2 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance 2 undo flush enable interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable 2 traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901 /system-index 一般按顺序排列，只要不重复即可。 interface GigabitEthernetX/X/X /下行接口 2 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 502 902 1702 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 4 nested-vlan 502 traffic-redirect inbound link-group 4001 rule 1 system-index 5 nested-vlan 1702 traffic-redirect inbound link-group 4001 rule 2 system-index 6 nested-vlan 902 interface GigabitEthernetX/X/X-01 /端口做为 instance 1 主用， instance 2 备用 port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 port smart-link group 1 master port smart-link group 2 slave interface GigabitEthernetX/X/X-02 /端口做为 instance 1 备用， instance 2 主用 port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 port smart-link group 1 slave port smart-link group 2 master 双网管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 为网络管理服务器段 4. 业务调试验证命令 display smart-link group 1 模式二：链路捆绑 +Smart-link 1. 板卡硬件要求： 要求板卡中带有“ DB”字样并且软件版本在 1267 以上、或者没有“ DB”字样软件版本在 1628 以上，可以支持灵活 QinQ 。 3 2. 软件版本要求： Release1600 以上可以配 Smart-link 3. 配置命令 定义 VLAN ACL acl number 4001 rule 0 permit ingress 51 to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress 45 egress any 定义外层 VLAN vlan 501 1701 901 定义链路组 link-aggregation group 1 mode manual link-aggregation group 2 mode manual smart-link 配置 stp region-configuration instance 1 vlan 501 901 1701 active region-configuration /每次更改配置后必须执行这条命令才生效 smart-link group 1 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance 1 link-aggregation group 1 master /链路组 1 作为 master link-aggregation group 2 slave /链路组 2 作为 slave undo flush enable interface GigabitEthernetX/X/X /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901 /system-index 一般按顺序排列，只要不重复即可。 interface GigabitEthernetX/X/X-01 /主用上行口 -1 port link-type trunk port trunk permit vlan 48 50 501 901 1701 port link-aggregation group 1 /把端口加入 link-aggregation group 1 4 interface GigabitEthernetX/X/X-02 /主用上行口 -2 port link-type trunk port trunk permit vlan 48 50 501 901 1701 port link-aggregation group 1 /把端口加入 link-aggregation group 1 interface GigabitEthernetX/X/X-03 /备用上行口 -1 port link-type trunk port trunk permit vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入 link-aggregation group 2 interface GigabitEthernetX/X/X-04 /备用上行口 -2 port link-type trunk port trunk permit vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入 link-aggregation group 2 双网管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 为网络管理服务器段 4. 业务调试验证命令 display smart-link group 1 display link-aggregation verbose 模式三：单链路 /链路捆绑 +VLAN 双向透传 1. 板卡硬件要求： 要求板卡 中带有“ DB”字样并且软件版本在 1267 以上、或者没有“ DB”字样软件版本在 1628 以上，可以支持灵活 QinQ。 2. 软件版本要求： 无特殊要求 3. 配置命令 定义 VLAN ACL acl number 4001 rule 0 permit ingress 51 to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress 45 egress any 5 定义外层 VLAN vlan 501 1701 901 VLAN 双 向透传配置 interface GigabitEthernetX/X/X /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901 /system-index 一般按顺序排列，只要不重复即可。 interface GigabitEthernetX/X/X-01 /上行口 1 port link-type trunk port trunk permit vlan 48 50 501 901 1701 interface GigabitEthernetX/X/X-02 /上行口 2 port link-type trunk port trunk permit vlan 49 501 901 1701 双网管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 为网络管理服务器段 4. 业务调试验证命令 display vlan X/X/X 华为 S9300 模式一：单链路 +Smar-link 灵活 QINQ 配置：（ S9300 主机版本为 V100R001 版本或业务单板类型最后一个字母为 A的单板使用如下流策略配置灵活 QINQ） 6 1、 定义内 层 VLAN 的流策略： traffic classifier QINQA-1 if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户 VLAN traffic classifier QINQA-2 if-match vlan-id 43 /匹配 iTV 用户 VLAN traffic classifier QINQA-3 if-match vlan-id 45 /匹配 ITMS 终端管理 VLAN # traffic behavior QINQA-1 nest top-most vlan-id 501 /外层 VLAN traffic behavior QINQA-2 nest top-most vlan-id 901 /外层 VLAN traffic behavior QINQA-3 nest top-most vlan-id 1701 /外层 VLAN # traffic behavior QINQB-1 nest top-most vlan-id 502 /外层 VLAN traffic behavior QINQB-2 nest top-most vlan-id 902 /外层 VLAN traffic behavior QINQB-3 nest top-most vlan-id 1702 /外层 VLAN # traffic policy QINQA classifier QINQA-1 behavior QINQA-1 classifier QINQA-2 behavior QINQA-2 classifier QINQA-3 behavior QINQA-3 traffic policy QINQB classifier QINQA-1 behavior QINQB-1 classifier QINQA-2 behavior QINQB-2 classifier QINQA-3 behavior QINQB-3 2、 定义外层 VLAN vlan batch 501 502 901 902 1701 1702 3、 接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound # 7 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy QINQB inbound # 灵活 QINQ 配置：（ S9300 主机版本为 V100R002 版本或业务单板最后一个字母非 A 的单板使用如下 STACKING 配置灵活 QINQ） 1、 定义外层 VLAN vlan batch 501 502 901 902 1701 1702 2、接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501 port vlan-stacking vlan 43 stack-vlan 901 port vlan-stacking vlan 45 stack-vlan 1701 # interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 502 port vlan-stacking vlan 43 stack-vlan 902 port vlan-stacking vlan 45 stack-vlan 1702 # smart-link 配置 stp region-configuration instance 1 vlan 501 901 1701 instance 2 vlan 502 902 1702 active region-configuration /每次更改 配置后必须执行这条命令才生效 smart-link group 1 protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable 8 port GigabitEthernet1/0/1 master port GigabitEthernet1/0/2 slave timer wtr 30 /配置主端口恢复 30s 后 恢复 smart-link group 2 protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port GigabitEthernet1/0/2 master port GigabitEthernet1/0/1 slave timer wtr 30 /配置主端口恢复 30s 后恢复 # interface GigabitEthernet1/0/1 /端口做为 instance 1 主用， instance 2 备用 port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 # interface GigabitEthernet1/0/2 /端口做为 instance 1 备用， instance 2 主用 port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 双网管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 为网络管理服务器段 业务调试验证命令 display smart-link group 1 模式二：链路捆绑 +Smart-link 灵活 QINQ 配置：（ S9300 主机版本为 V100R001 版本或业务单板类型最后一个字母为 A的单板使用如下流策略配置灵活 QINQ） 1、 定义内层 VLAN 的流策略： traffic classifier QINQA-1 if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户 VLAN traffic classifier QINQA-2 if-match vlan-id 43 /匹 配 iTV 用户 VLAN traffic classifier QINQA-3 9 if-match vlan-id 45 /匹配 ITMS 终端管理 VLAN # traffic behavior QINQA-1 nest top-most vlan-id 501 /外层 VLAN traffic behavior QINQA-2 nest top-most vlan-id 901 /外层 VLAN traffic behavior QINQA-3 nest top-most vlan-id 1701 /外层 VLAN # traffic behavior QINQB-1 nest top-most vlan-id 502 /外层 VLAN traffic behavior QINQB-2 nest top-most vlan-id 902 /外层 VLAN traffic behavior QINQB-3 nest top-most vlan-id 1702 /外层 VLAN # traffic policy QINQA classifier QINQA-1 behavior QINQA-1 classifier QINQA-2 behavior QINQA-2 classifier QINQA-3 behavior QINQA-3 traffic policy QINQB classifier QINQA-1 behavior QINQB-1 classifier QINQA-2 behavior QINQB-2 classifier QINQA-3 behavior QINQB-3 2、 定义外层 VLAN vlan batch 501 502 901 902 1701 1702 3、 接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound # interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy QINQB inbound 10 # 灵活 QINQ 配置：（ S9300 主机版本为 V100R002 版本或业务单板最后一个字母非 A 的单 板使用如下 STACKING 配置灵活 QINQ） 1、 定义外层 VLAN vlan batch 501 502 901 902 1701 1702 2、接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501 port vlan-stacking vlan 43 stack-vlan 901 port vlan-stacking vlan 45 stack-vlan 1701 # interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 502 port vlan-stacking vlan 43 stack-vlan 902 port vlan-stacking vlan 45 stack-vlan 1702 # smart-link 配置 stp region-configuration instance 1 vlan 501 901 1701 instance 2 vlan 502 902 1702 active region-configuration /每次更改配置后必须执行这条命令才生效 smart-link group 1 protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port Eth-Trunk1 master port Eth-Trunk2 slave timer wtr 30 /配置主端口恢复 30s 后恢复 smart-link group 2 protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 11 smart-link enable port Eth-Trunk2 master port Eth-Trunk1 slave timer wtr 30 /配置主端口恢复 30s 后恢复 # interface GigabitEthernetX/X/X-01 /主用上行口 -1 Eth-Trunk1 /把端口加入 link-aggregation group 1 interface GigabitEthernetX/X/X-02 /主用上行口 -2 Eth-Trunk1 /把端口加入 link-aggregation group 1 interface GigabitEthernetX/X/X-03 /备用上行口 -1 Eth-Trunk2 /把端口加入 link-aggregation group 2 interface GigabitEthernetX/X/X-04 /备用上行口 -2 Eth-Trunk2 /把端口加入 link-aggregation group 2 interface Eth-Trunk1 /端口做为 instance 1 主用， instance 2 备用 port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 # interface Eth-Trunk2 /端口做为 instance 1 备用， instance 2 主用 port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 双网 管地址配置 interface vlan 48 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 为网络管理服务器段 业务调试验证命令 display smart-link group 1 display link-aggregation verbose 模式三：单链路 /链路捆绑 +VLAN 双向透传 灵活 QINQ 配置：（ S9300 主机版本为 V100R001 版本或业务单板类型最后一个字母为 A的单板使用如下流策略配置灵活 QINQ） 12 1、 定义内层 VLAN 的流策略： traffic classifier QINQA-1 if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户 VLAN traffic classifier QINQA-2 if-match vlan-id 43 /匹 配 iTV 用户 VLAN traffic classifier QINQA-3 if-match vlan-id 45 /匹配 ITMS 终端管理 VLAN # traffic behavior QINQA-1 nest top-most vlan-id 501 /外层 VLAN traffic behavior QINQA-2 nest top-most vlan-id 901 /外层 VLAN traffic behavior QINQA-3 nest top-most vlan-id 1701 /外层 VLAN # traffic behavior QINQB-1 nest top-most vlan-id 502 /外层 VLAN traffic behavior QINQB-2 nest top-most vlan-id 902 /外层 VLAN traffic behavior QINQB-3 nest top-most vlan-id 1702 /外层 VLAN # traffic policy QINQA classifier QINQA-1 behavior QINQA-1 classifier QINQA-2 behavior QINQA-2 classifier QINQA-3 behavior QINQA-3 traffic policy QINQB classifier QINQA-1 behavior QINQB-1 classifier QINQA-2 behavior QINQB-2 classifier QINQA-3 behavior QINQB-3 2、 定义外层 VLAN vlan batch 501 502 901 902 1701 1702 3、 接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound # 13 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy QINQB inbound # 灵活 QINQ 配置：（ S9300 主机版本为 V100R002 版本或业务单板最后一个字母非 A 的单板使用如下 STACKING 配置灵活 QINQ） 1、定义外层 VLAN vlan batch 501 502 901 902 1701 1702 2、接口配置 interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501 port vlan-stacking vlan 43 stack-vlan 901 port vlan-stacking vlan 45 stack-vlan 1701 # interface GigabitEthernetX/X/X /下行接口 1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50 为 DSLAM 管理 VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 502 port vlan-stacking vlan 43 stack-vlan 902 port vlan-stacking vlan 45 stack-vlan 1702 # interface GigabitEthernetX/X/X-01 /上行口 1 port link-type trunk port trunk permit vlan 48 50 501 901 1701 interface GigabitEthernetX/X/X-02 /上行口 2 port link-type trunk port trunk permit vlan 49 501 901 1701 双网管地址配置 interface vlan 48 14 ip address A.B.C.2 255.255.255.252 interface vlan 49 ip address A.B.C.6 255.255.255.252 ip route 0.0.0.0 0.0.0.0 A.B.C.1 ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0 为网络管理服务器段 业务调试验证命令 display vlan X/X/X 中兴 T64G 模式一：单链路 +ZESS-link 1. 板卡硬件要求： 每台 T64G 至少配置 1 块 UGSF 板卡 2. 软件版本要求： V2.8.01B19 或 V2.8.01C20 以上 3. 配置命令 全局配置 STP spanning-tree enable /全局配置为 stp enable，所有端口配置为 stp disable spanning-tree mst configuration instance 1 vlan 501,1701.901 instance 2 vlan 502,1702.902 端口配置 interface gei_1/1 /下行 customer-port 配置 switchport mode hybrid switchport hybrid native vlan 501 /见注意事项 1 switchport hybrid vlan 50 tag switchport hybrid vlan 901 untag switchport hybrid vlan 1701 untag switchport qinq customer /定义端口为 C 口 spanning-tree disable /关闭 STP interface gei_1/2 /下行 customer-port 配置 switchport mode hybrid switchport hybrid native vlan 502 /见注意事项 1 switchport hybrid vlan 50 tag switchport hybrid vlan 902 untag switchport hybrid vlan 1702 untag 15 switchport qinq customer /定义端口为 C 口 spanning-tree disable /关闭 STP interface gei_1/24 /上行 uplink-port 配置 switchport mode hybrid switchport hybrid native vlan 48 switchport hybrid vlan 48 tag switchport hybrid vlan 50 tag switchport hybrid vlan 501-502 tag switchport hybrid vlan 1701-1702 tag switchport hybrid vlan 901-902 tag switchport hybrid vlan 2 untag switchport qinq uplink /定义端口为 U 口 spanning-tree disable /关闭 STP interface gei_2/24 /上行 uplink-port 配置 switchport mode hybrid switchport hybrid native vlan 49 switchport hybrid vlan 49 tag switchport hybrid vlan 501-502 tag switchport hybrid vlan 1701-1702 tag switchport hybrid vlan 901-902 tag switchport qinq uplink /定义端口为 U 口 spanning-tree disable /关闭 STP session 设置 vlan qinq session-no 1 customer-port gei_1/1 uplink-port gei_1/24 in-vlan 50 untag helper-vlan 2 undirect vlan qinq session-no 2 customer-port gei_1/1 uplink-port gei_1/24 in-vlan 2051-3050 ovlan 1701 undirect vlan qinq session-no 3 customer-port gei_1/1 upl