外文翻译--汽车变速器设计

1 附 录 原文： Transmission design As we all know,automobile engine to a certain speed can be achieved under the best conditions, when compared issued by the power, fuel economy is relatively good. Therefore, we hope that the engine is always in the best of conditions to work under. However, the use of motor vehicles need to have different speeds, thus creating a conflict. Transmission through this conflict to resolve. Automotive Transmission role sum up in one sentence, called variable speed twisting, twisting or slow down the growth rate by increasing torsional. Why can slow down by twisting, and the growth rate but also by twisting? For the same engine power output, power can be expressed as N = wT, where w is the angular velocity of rotation, and T Niuju. When N fixed, w and T is inversely proportional to the. Therefore, the growth rate will reduce twisting, twisting slowdown will increase. Automotive Transmission speed gear based on the principle of variable twisted into various stalls of different transmission ratio corresponding to adapt to different operational conditions. General to set up a manual gearbox input shaft, intermediate shaft and output shaft, also known as the three-axis, as well as Daodang axis. Three-axis is the main transmission structure, input shaft speed is the speed of the engine, the output shaft speed is the intermediate shaft and output shaft gear meshing between different from the speed. Different gears are different transmission ratio, and will have a different speed. For example Zhengzhourichan ZN6481W2G manual transmission car-SUV, its transmission ratio are: 1 File 3.704:1； stalls 2.202:1； stalls 1.414:1； stalls 1:1 5 stalls (speeding file) 0.802: 1. When drivers choose a launch vehicle stalls, Plectrum will be 1 / 2 file synchronization engagement with a back stall gear and output shaft lock it, the power input shaft, intermediate shaft and output shaft gear of a stall, a stall the output shaft gear driven, and the output shaft power will be transmitted to the drive shaft (red arrow). A typical stall Biansuchilun transmission ratio is 3:1, that is to say three laps to the input shaft and output shaft to a circle. When the growth rate of car drivers choose two stalls, Plectrum will be 1 / 2-file 2 synchronization and file a joint separation after 2 stall and lock the output shaft gear, power transmission line similar, the difference is that the output shaft gear of a stall 2 stall replaced by the output shaft gear driven. 2 stall Biansuchilun typical transmission ratio is 2.2:1, 2.2 laps to the input shaft and output shaft to a circle than a stall speed increase, lower torque. When refueling vehicle drivers growth stalls option 3, Plectrum to 1 / 2 back to the free file-synchronization position, and also allows the 3 / 4 file synchronization Mobile stall until 3 in the output shaft gear lock, power can be into the shaft axis - intermediate shaft - the output shaft of the three stalls Biansuchilun, led through three stalls Biansuchilun output shaft. 3 stalls typical transmission ratio is 1.7:1, 1.7 laps to the input shaft and output shaft to a circle is further growth. When car drivers Option 4 refueling growth stalls, Plectrum will be 3 / 4 from the 3-file synchronization stall gear directly with the input shaft gear joint initiative, and power transmission directly from the input shaft to the output shaft, the transmission ratio at 1:1, that the input shaft and output shaft speed the same. The driving force without intermediate shaft, also known as direct file, the file transmission than the maximum transmission efficiency. Most cars run-time files are used directly to achieve the best fuel economy. Shift into the first interval when, in a free transmission when Biansuchilun output shaft is not locked in, they can not rotate the output shaft driven, not power output. General automotive manual transmission than the main 1-4 stalls, usually the first designers to determine the minimum (one stall) and maximum (4 files) transmission ratio, the middle stall drive by geometric progression than the general distribution. In addition, there are stalls Daodang and speeding, speeding file is also known as the five stalls. When the car to accelerate to more than car drivers with the choice of five stalls, and a typical five-transmission ratio is 0.87:1, which is driven by a pinion gear, the gear when the initiative to 0.87 zone, passive gear have been transferred to a circle of the End. Dao Dang, the opposite direction to the output shaft rotation. If one pair of meshing gears when we reverse rotation, with a middle gear, it will become the same to the rotation. Use of this principle, we should add a gear Daodang the media will be rotational direction reversed, it will have a Daodang axis. Daodang installed in the transmission shaft independent crust, and the intermediate shaft parallel axis gear with the intermediate shaft and output shaft gear meshing gears, will be contrary to the output shaft. 3 Daodang usually used for the synchronization control also joins five stalls, stalls and Daodang 5 position in the same side. As a middle gear, the general transmission Daodang transmission ratio greater than 1 file transmission ratio, by twisting, steep slope with some vehicles encountered on the progress stalls falters with a Daodang boost. Ride from the driver of the considerations, better transmission stall, stall adjacent stall more than the transmission changes the ratio of small, and easy to shift smoothly. However, the shortcomings of the stalls is more transmission structure is complicated, bulky, light vehicle transmission is generally 4-5 stalls. At the same time, transmission ratio is not integral, but with all of the decimal point, it is because of the gear teeth meshing is not caused by the whole multiples of two gear teeth can lead to the whole multiples of two meshing gears of uneven wear, making the tooth surface quality have a greater difference. Manual transmission and synchronizer Manual transmission is the most common transmission, or MT. Its basic structure sum up in one sentence, is a two-axle shaft, where input shaft, the shaft axis and intermediate shaft, which constitute the main body of the transmission and, of course, a Daodang axis. Manual transmission known as manual gear transmission, which can be in the axial sliding gears, the gears meshing different variable speed reached twisting purpose. Typical manual transmission structure and principles are as follows. Input shaft also said that the first axis, and its front-end Spline driven directly with the clutch disc sets with the Spline, by the transfer of torque from the engine. The first axis of the intermediate shaft and gears meshing gears often, as long as the shaft axis to a turn, the intermediate shaft and gear also will be rotating. Vice also said intermediate shaft axis, the axis-even more than the size gear. Also known as the second output shaft axis, the axis of various sets of gear stall progress can be manipulated at any time in the role of the device and the corresponding intermediate shaft gear meshing, thus changing its speed and torque. With the end of the output shaft spline associated with the drive shaft through the drive shaft torque transmitted to the drive axle reducer. Thus, progress stalls drive transmission path is: input shaft gear often rodents - often rodents intermediate shaft gear - corresponding intermediate shaft gear - the second axis corresponding gear. Reversing the gear shaft can be manipulated by the device pick in the axis movement, and the intermediate shaft and output shaft gear meshing gears, to the contrary to the direction of rotation output. Most cars have five stalls and a Daodang forward, a certain degree of each stall 4 transmission ratio, the majority of stalls transmission ratio greater than 1, 4 file transmission ratio of 1, known as direct stalls, and transmission ratio is less than 1 No. 5 stall called accelerated stall. Free at the output shaft gear in a position of non-engagement, unacceptable power transmission. The transmission input shaft and output shaft rotational speed to their own, transform a stall when there is a synchronous. Two different rotational speed gear meshing force will impact the collision occurred, damage gear. Therefore, the old transmission shift to a feet-off approach, or stall on the location of the free stay for a while by stalls in the free position refueling doors, in order to reduce the speed differential gear. However, this operation is relatively more complicated and difficult to grasp accurate. So designers create a synchronized, and allows synchronization through the meshing of gears to be consistent speed and smooth meshing. At present Synchronous Transmission is based on the synchronization of inertia, mainly from joint sets, synchronous lock ring, and so on, it is characterized by friction on the role of synchronization. Splice sets Genlock engagement ring gear and the ring gear when it had Chamfer (Lock angle), Genlock within the cone ring gear engagement with the question of cone ring gear contact friction. Lock and cone angle has been made in the design of an appropriate choice to be made friction cone of the teeth meshing with the ring gear quickly sets pace at the same time will have a Lock role and to prevent the gears meshing in sync before. When synchronization lock cone ring gear engagement with the question of cone ring gear after contact in the effects of friction torque gear speed quickly lower (or higher) with the same speed synchronous lock ring, the two synchronous rotation of the gear Genlock Central zero speed, thus moment of inertia also disappear, then in force under the impetus of engagement sets unhindered and synchronization lock ring gear engagement, and further engagement with the question of gear engagement and the completion Gear Shift Process. The automatic gearbox The automatic gearbox chooses to block the pole the equal to moving the stick shift of the gearbox, having generally below several blocks:P( parking), R( pour to block), N( get empty to block), D( go forward), S( or2, namely for 2 block soon), L.( or1, namely for 1 block soon)This several an usage for blocking a right usages coming driver the automatic gearbox is automotive of person to say particularly important, underneath let us very much familiar with once automatic gearbox eachly blockings main theme. The usage of the P ( the parking blocks) 5 The launches the luck turns as long as choose to block the pole in driving the position, automatic gearbox car run about very easily.But park, choose to block the pole must pull into of P, from but pass the internal parking system in gearbox moves the device will output the stalk lock lives, combining to tense the hand system move, preventing the car ambulation. The usage of the R( pour to block) R a control for is pouring blocking, using inside wanting slicing recording, automatic gearbox car unlike moving gearbox car so can using half moving, so while reversing the car wanting special attention accelerating pedal. The usage of the N( get empty to block) The N is equal to get empty to block, can while starting or hour of trailer usage.At wait for the signal or block up the car will often often choose to block the pole keeps in the of D, trampling at the same time the next system move.If time is very short, do like this is an admission of, but if stop the time long time had better change into of N, combine to tense the hand system moves.Because choose to block the pole in driving the position, the automatic gearbox car has generally and all to drive the trend faintly, long hours trample the system move same as a deterrent this kind of trend, make gearbox oil gone up, the oil liquid changes in character easily.Particularly in the air condition machine work, launch the soon higher circumstance in machine bottom more disadvantageous.Some pilots for the sake of stanza oil, at made good time or go down slope will choose to block the pole pull the of N skids, this burn the bad gearbox very easily, launching the machine to revolves soon in the however because the gearbox outputs at this time the stalk turns soon very high, the oil pump provides the oil shortage, lubricating the condition worsen, burn the bad gearbox easily. The usage of the D( go forward to block) Will choose to block when is normal to drive the pole put in the of D, car can at 1 4 block( or 3 block) its change to block automatically.The of D drives the position most in common usely.What demand control is:Because the automatic gearbox is soon high and low with car to come to make sure to block according to the accelerator size a, so accelerate the pedal operation method is different, changing to block the hour of the car is soon too not same alike.If start hour quick accelerate the pedal tramples the bottom, rising to block the night, accelerating the ability is strong, arriving certain car soon behind, then will accelerate the pedal loosen to open very quickly, car can rise to block immediately, launch like this the machine voice is small, comfortable good. 6 The another characteristics of the D is a compulsory low blocking, easy to high speed the hour overtakes a car, will accelerate quickly in of D drove the pedal trample after all, connect the compulsory low fend off the pass and then can reduce to block automatically, the car accelerates very quickly, after overtaking a car loosen to open the pedal of acceleration to can rise to block automatically again. The usage of the S, of L low the usage that block The automatic gearbox in in is placed in the low blocking the scope on of S or of Ls, can usage under an etc. circumstance.It change to can make use of to launch well into of S or of Ls the mechanism move, avoiding the car wheel system move the machine over hot, cause the system move the effect descent while going down slope.But change into from the of D of S or of L, car soon cant higher than rise to block the car homologously soon, otherwise strong vibration in opportunity to launch, make gearbox oil hoicked, even will damage the gearbox. The is another at rain fog weather hour, if the road adheres to the term bad, can change into a position for or of L, fixing at somely first lowly blocking driving, doing not use can automatically changing blocking, in order to prevent the car beats slippery.Must keep firmly in mind at the same time, beat the slippery hour can will choose to block the pole pushes into a motive for, cutting off launching machine, toing guarantee a car the safety. 汽车 变速器设计 -外文翻译 我们知道，汽车发动机在一定的转速下能够达到最好的状态，此时发出的功率比较大，燃油经济性也比较好。因此，我们希望发动机总是在最好的状态下工作。但是，汽车在使用的时候需要有不同的速度，这样就产生了矛盾。这个矛盾要通过变速器来解决。 汽车变速器的作用用一句话概括，就叫做变速变扭，即增速减扭或减速增扭。为什么减速可以增扭，而增速又要减扭呢？设发动机输出的功率不变，功率可以表示为 N = wT，其 中 w是转动的角速度， T是扭距。当 N固定的时候， w与 T是成反比的。 7 所以增速必减扭，减速必增扭。汽车变速器齿轮传动就根据变速变扭的原理，分成各个档位对应不同的传动比，以适应不同的运行状况。 一般的手动变速器内设置输入轴、中间轴和输出轴，又称三轴式，另外还有倒档轴。三轴式是变速器的主体结构，输入轴的转速也就是发动机的转速，输出轴转速则是中间轴与输出轴之间不同齿轮啮合所产生的转速。不同的齿轮啮合就有不同的传动比，也就有了不同的转速。例如郑州日产 ZN6481W2G 型 SUV车手动变速器，它的传动比分别是： 1档 3.704:； 2档 2.202:1； 3档 1.414:1； 4档 1:1； 5档（超速档）0.802:1。 当汽车启动司机选择 1档时，拨叉将 1/2 档同步器向后接合 1档齿轮并将它锁定输出轴上，动力经输入轴、中间轴和输出轴上的 1档齿轮， 1档齿轮带动输出轴，输出轴将动力传递到传动轴上（红色箭头）。典型 1档变速齿轮传动比是 3:1,也就是说输入轴转 3圈，输出轴转 1圈。 当汽车增速司机选择 2档时，拨叉将 1/2档同步器与 1档分离后接合2档齿轮并锁定输出轴上，动力传递路线相似，所不同的是输出轴上的 1档齿轮换成2档齿轮带动输出轴 。典型 2档变速齿轮传动比是 2.2:1，输入轴转 2.2圈，输出轴转 1圈，比 1档转速增加，扭矩降低。 当汽车加油增速司机选择 3 档时，拨叉使 1/2档同步器回到空档位置，又使 3/4档同步器移动直至将 3档齿轮锁定在输出轴上，使动力可以从轴入轴 中间轴 输出轴上的 3 档变速齿轮，通过 3档变速齿轮带动输出轴。典型 3档传动比是1.7:1，输入轴转 1.7 圈，输出轴转 1圈，是进一步的增速。 当汽车加油增速司机选择 4档时，拨叉将 3/4档同步器脱离 3档齿轮直接与输入轴主动齿轮接合，动力直接从输入轴传递到输出轴，此时传动 比 1:1，即输出轴与输入轴转速一样。由于动力不经中间轴，又称直接档，该档传动比的传动效率最高。汽车多数运行时间都用直接档以达到最好的燃油经济性。 换档时要先进入空档，变速器处于空档时变速齿轮没有锁定在输出轴上，它们不能带动输出轴转动，没有动力输出。 8 一般汽车手动变速器传动比主要分上述 1 4档，通常设计者首先确定最低（ 1档）与最高（ 4档）传动比后，中间各档传动比一般按等比级数分配。另外，还有倒档和超速档，超速档又称为 5档。 当汽车要加速超过同向汽车时司机选择 5档，典型 5档传动比是 0.87:1，也就是用大齿轮带动小齿轮，当主动齿轮转 0.87 圈时，被动齿轮已经转完 1圈了。 倒档时输出轴要向相反方向旋转。如果一对齿轮啮合时大家反向旋转，中间加上一个齿轮就会变成同向旋转。利用这个原理，倒档就要添加一个齿轮做“媒介”，将轴的转动方向调转，因此就有了一根倒档轴。倒档轴独立装在变速器壳内，与中间轴平行，当轴上齿轮分别与中间轴齿轮和输出轴齿轮啮合时，输出轴转向会相反。 通常倒档用的同步器也控制 5档的接合，所以 5档与倒档位置是在同一侧的。由于有中间齿轮，一般变速器倒档传动比大于 1档传动比， 增扭大，有些汽车遇到陡坡用前进档上不去就用倒档开上去。 从驾驶平顺性考虑，变速器档位越多越好，档位多相邻档间的传动比的比值变化小，换档容易而且平顺。但档位多的缺点就是变速器构造复杂，体积大，现在轻型汽车变速器一般是 4 5档。同时，变速器传动比都不是整数，而是都带小数点的，这是因为啮合齿轮的齿数不是整倍数所致，两齿轮齿数是整倍数就会导致两齿轮啮合面磨损不均匀，使得轮齿表面质量产生较大的差异。 手动变速器与同步器 手动变速器是最常见的变速器，简称 MT。它的基本构造用一句话概括，就是两轴一中轴，即指输入轴、轴出轴和中间轴，它们构成了变速器的主体，当然还有一根倒档轴。手动变速器又称手动齿轮式变速器，含有可以在轴向滑动的齿轮，通过不同齿轮的啮合达到变速变扭目的。典型的手动变速器结构及原理如下。 输入轴也称第一轴，它的前端花键直接与离合器从动盘的花键套配合，从而传递由发动机过来的扭矩。第一轴上的齿轮与中间轴齿轮常啮合，只要轴入轴一转，中间 9 轴及其上的齿轮也随之转动。中间轴也称副轴，轴上固连多个大小不等的齿轮。输出轴又称第二轴，轴上套有各前进档齿轮，可随