CT扩散炉培训教材(设备中英文版).ppt_第1页
CT扩散炉培训教材(设备中英文版).ppt_第2页
CT扩散炉培训教材(设备中英文版).ppt_第3页
CT扩散炉培训教材(设备中英文版).ppt_第4页
CT扩散炉培训教材(设备中英文版).ppt_第5页
已阅读5页,还剩31页未读 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

1、centrotherm扩散炉设备培训 equipment training of centrotherm Diffusion furnace,Centrotherm扩散炉的组成,ALoading box 推舟部分 B. TGA 有毒气体排放 C. Heating furnace 加热部分 D. Gas cabinet 气柜,设备 平面结构Equipment plane structure,1、CMI电脑 2、Loading box上料箱 3、Toxic gases 有毒气体排放 4、Furnace 炉体 5、Gas box 气源柜,Loading box上料箱,Baddle head 舟头,L

2、oading wafer 加栽的硅片,Loading box上料箱,Mechanical arm 机械臂,Loading box 上料箱,Storage rack 1,2 存储位1、2,Paddle bearing, adjustable paddle position 碳化硅桨支座,调节桨位置,TGA有毒气体排放,quartz door 石英门,Door cylinder炉门气缸,Heating furnace炉膛,1、CMS module 3、Power connection cover 2、Thermocouple connection 4、Temperature sensor modu

3、le,Gas cabinet气源柜,1、 Flow meter 气体流量计 2、 Pneumatic valve 气动阀,1,2,Cooling water inlet and water system冷却水系统,Cooling to the top of the furnace body and furnace 对炉膛顶部和炉体进行冷却,Thermostatic bath恒温槽,On the POCL3 constant temperature process, normal temperature 20 degrees 对POCL3进行恒温作用,正常工艺温度20度,Silicon carb

4、ide paddle碳化硅桨,Bearing quartz and silicon, and out of the carrier ship 承载石英舟和硅片 石英舟进出的载体,Range detection alarm 范围检测报警器,Detection of a range of whether object, avoid hit boat phenomenon, this range can be adjusted 检测某个范围内是否有物体,避免出现撞舟现象,些范围可进行调节,Communication Network Overview通信网络总览,Heating system加热系统,

5、Cooling system冷却系统,1、Heat exchanger 2、Cooling 3、Shutoff valve,1、Cooling 4、Heat exchanger 2、The main fan 5、Electronic devices 3、Cooling the air passage,Alarm lamp information,Operation panel操作面板,operation panel 4 keyboard Touch screen 5 touch screen button USB socket,Operation panel操作面板,The equipment

6、 has the following button Stop action -All the mechanical action of loading box are stop Loading box lighting-openclose the lamp of the loading box Autohand manual switch-Loading and unloading of the operating system can manual operation in an open feeding box 4 Allows to unlock- Press this button ,

7、to unlock the car,Operation panel操作面板,1 pushbutton ABC keyboard call 4 pushbutton right mouse button Pushbutton task change 5 pushbutton shift Pushbutton brightness ABC keyboard call-calls upclosses the keyboard on the touchscreen, keyboard entries can be carried out directly on the touchsceen. Push

8、button task change-changes a task windows Pushbutton brightness-press this button together with the shife button to increase the brightness of the touchscress. Pushbutton right mouse buttonopens right mouse button context menu,press this button together with the shift button to reduce the touchscree

9、n. Pushbutton shiftcalls up the second keyboard level,push this bushbutton together with the required function button.,CMI interface CMI桌面信息,System name 7 alarm close Date time 8 notes Centrotherm logo and system 9 additional information Information button Current display area in the 10 system mode

10、Information field 11 connection state with CECGEM System status Loginlogout button,CMI interface CMI桌面信息,Jobs 4 setup System 5 alarms Datslog 6 help(online help),The CMI user interface CMI使用者桌面,Title bar 3 navigation bar Command bar 4 information field with variable field areas,简单介绍CESAR界面 A brief i

11、ntroduction to CESAR interface,上图是CESAR的界面:1.系统工艺状态 2.工艺时间状态 3.时间日期 4.气体流量状态 5.系统准备状态 6. 温度检测显示 This is a CESAR interface: 1. System process 2. Process time 3. Time and date 4. Gas flow state 5. System readiness 6. Temperature detection and display,CT操作注意事项 CT operation matters needing attention,1.S

12、LS处于“UP”位置时,管内有舟时不可手动进桨 SLS in the UP position, the inner tube has a boat can not be manually into the paddle. 2.SLS处于“DOWN”位置时,桨上有舟时不得手动进舟。 SLS in the DOWN position, the paddle is not manually into the boat boat. 3.桨上有舟时,舟不在正确位置,不准切换到自动运行模式。 Oars on a boat, the boat is not in the correct position,

13、are not allowed to switch to automatic running mode.,CT操作注意事项 CT operation matters needing attention,4.进舟、退舟失败报警时,一定要检查舟的位置 是否在合理的位置,才可以对报警进行复位,自动/手动的切换要谨慎,若舟不在正确位置,请手动移至正确位置后再对报警进行复位(炉门以桨的位置作为开闭标准) Into the boat, boat back failure alarm, be sure to check the boat position is in a reasonable positio

14、n, can alarm reset, automatic / manual switch must be careful, if the ship is not in the correct position, please manually moved to the correct position after the alarm reset ( door to paddle position as opening and closing standard ),5.舟位于存储架(storage2,3)时,一定要确认存储架上 的感应器有没有感应到,否则有可能导致撞舟。 When the bo

15、at is located on the storage rack (storage2, 3),make sure that the storage rack sensor is sensed, otherwise may cause the bumped boat. 6.从手动切换自动时,Grip一定要在Middle位置, 否则机械臂可能因无法正常运行而报警。 From manual automatic, Grip must be in the Middle position, or mechanical arm may be due to normal operation and alar

16、m.,7.进舟后,工艺无法运行,先确认舟在桨上的位置,以及 Tube=ready SLS=UP TGA=YES 然后进行操作。 In the boat, technology cannot run, make sure the boat on the oar position, as well as Tube = ready SLS = UP TGA = YES then operation.,8.机械臂运动时不要上料,以免上料时抖动机械臂撞到舟。,As mechanical arm movement not feeding,in order to avoid feeding time jit

17、ter mechanical arm hit the boat。,9.单一炉管有故障时,应该及时琐闭并降温,以节约能源。,Single tube has fault, should be timely and closed and cooling, in order to save energy.,常见故障,1. Process recipe has terminated with error state AC 进行中的工艺以错误状态结 束警报确认 To store 储存 To store enable unload 储存并缷下 Restart recipe 重新开始工艺 A用于选错工艺号,手

18、动结束工艺, 重新开始新的其他工艺时进行选择 B多数情况下选择此项 C工艺中断需要重新进行时选择,但不建议使用, 建议选择(B) Process recipe has terminated with error state AC Ongoing process to end the error status Alarm confirmation To store To store enable unload Restart recipe A Used the wrong process number , Hand end of the process , Start a new choice

19、when other processes B In most cases, choice this one C Interrupts need to re-process the selection, but not recommended, recommended to choose (B) 。,Boat already in tube- Select:Process=0. Unload=1(.) 选择0或1 说明:当管内有舟存在时,异常排除 后手动运行工艺时会出现此提示 Boat already in tube- Select:Process=0. Unload=1(.) Descript

20、ion: When the tube has a boat there, the exception rule out runningprocess manually after this prompt will appear.,Lost homing check poti 失去引导,检 查位置(一般此警报会自动解除) 说明:此警报会自动解除,但需要 检查一下桨是否在原点位置即可 Lost homing check poti Check the location (usually the alarm will be automatically lifted) Description: This

21、 alarm will be automatically lifted, but need Check whether the origin location to paddle,4. Recipe abort 2-process abort to continue : enter AB 工艺退出运行终止!继续,请输入AB 说明:对工艺异常结束的手动确认,然后就会出现报警 Recipe abort 2-process abort to continue : enter AB Description: The manual confirmation process ends, 5. Recipe

22、 couldnt be started please check protocol for reason! 工艺不能运行,请检查原因 Recipe couldnt be started please check protocol for reason!,. 6. Boat sensor of grad has changed without permission 机械手上的传感器被非允许的改动 说明:机械臂在上下移动的时候,前后不能移动, 若前后位置发生移动机械将被锁定,出现报警, 此报警需设备人员的密码登陆在Handing 对话框中的Tech模式下进行复位 Boat sensor of gr

23、ad has changed without permission Description: The robotic arm to move up and down when you can notmove around,if the location is moved around the machine will be locked, an alarm, the alarmequipment, personnel need to log in a password dialog box in the Tech Handingreset mode,7.There is already an active recipe 工艺名 from local tisting 已有工艺在此管的工艺列表中 说明:这两个报警经常出现,若能够确认此管未有 工艺在运行,就必须将此管重新启动, 如果有工艺运行,可以将工艺手动停止, 或者等待工艺结束。 There is already an active recipe from local tis

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论