制粒工艺过程的水分控制

2021/6/271影响颗粒稳定度的因素调制20％环模15％粉碎粒度20％配方/原料40％冷却5%2021/6/272蒸汽调制的基本作用热－水分交换使饲料原料软化，淀粉糊化，促进粉料颗粒在压粒过程中紧密结合，提高颗粒饲料的稳定度，减少含粉量。降低制粒电耗，提高产量，延长环模寿命，减少因摩擦生热导致的有效营养成分损失。2021/6/273淀粉糊化程度取决于：温度、水分与时间制粒前的常规蒸汽调制，淀粉糊化度的提高一般不超过五个百分数单位压粒过程摩擦生热导致的淀粉糊化无助于提高颗粒稳定度蒸汽调制的基本作用2021/6/274调制料温、制粒升温与淀粉糊化的关系

2021/6/275蒸汽调制的基本作用高水分、长时间蒸汽调制，如湿法挤压膨化的预调制过程，可使淀粉糊化度提高约20个百分数单位。2021/6/276蒸汽调制的关键蒸汽质量：什么是蒸汽质量？如何得到高质量蒸汽根据饲料类型和调制时间长短正确设定调制气压原料与成品水分控制2021/6/277蒸汽调制过程的热交换蒸汽热量的组成：表观热与潜热潜热---物料升温的主要热量来源:每凝结一个百分数单位的优质蒸汽，物料温度大约上升150C蒸汽表蒸汽质量2021/6/278蒸汽表over2021/6/279蒸汽质量湿蒸汽－蒸汽中含液态水,热量低，易堵塞模孔蒸汽质量可用气态水在蒸汽中的百分数来表示测定蒸汽质量的方法过热蒸汽或不饱和蒸汽判定过热蒸汽的方法理想的蒸汽：100％饱和蒸汽2021/6/2710蒸汽质量的计算

蒸汽质量% ={[(W2xT2-W1xT1)/(W2-W1)-Hf]/Hfg}x100% W1=注入蒸汽前水重

W2=注入蒸汽前水重

T1=注入蒸汽前水温

T2=注入蒸汽前水温

Hf=测试压力下的表观热(查蒸汽表) Hfg=测试压力下的潜热(查蒸汽表)2021/6/2711蒸汽表over2021/6/2712蒸汽系统主要设备的选择与设定锅炉输汽管道内径的确定汽水分离器疏水阀减压(稳压)器流量控制阀2021/6/2713

锅炉的选择与设置

BoilerSelectionandLayout

燃料的选择要全面考虑供气稳定性、人工、燃料价格及环境等因素

FuelType锅炉的功率或供气量要留有余地

BoilerSize:

Leavesufficientroom

尽可能缩短锅炉与用汽设施之间的距离

Locationoftheboiler:closetothepelletmill2021/6/2714ID(cm)=Wx3.53v/30W=蒸汽流量(Steamflow),kg/minv=给定气压下的比体积(Specificvolumeundergivensteampressure),m3/kg(查表)30=最大流速(allowedsteamflowvelocity),m/s输汽管道内径的确定

SizingthePipe2021/6/2715气水分离器

SteamSeparator根据机械原理将蒸汽中的水滴与蒸气分开以得到优质蒸汽. Usingamechanicaladvicetoremovewaterdrip-letsfromthesteamandobtainhighqualitysteam.好的气水分离器可移走98%的水滴. Goodseparatorcanremovemorethan98%ofthewaterdrip-lets2021/6/2716其功能为将凝积水(在进入调制器前)从蒸汽系统中排出.

Toremovewatercondensateoutofthesteamsystem(beforethesteamgoingintotheconditioner).疏水阀应不时启闭使一定压力下的凝积水移到常压的回收系统且不丢失蒸気.

Itmustperiodicallyopenandclosetoallowthepressurizedcondensatetoberemovedintoanatmosphericcondensatereturnsystemwithoutlosingsteam.疏水阀

CheckValve2021/6/2717只有气压稳定才能使气流稳定,从而保证制粒过程稳定.

Steadypressureiscriticalforsmoothsteamflowandhencesmoothpelletingoperation.减压有助于提高蒸汽质量.

Pressurereductionhelpsimprovingsteamquality.减压(稳压)器的主要参数:流量、调压范围及控制的稳定性(可用变异系数度量). Parametersforconsideration:Maximumflow(kg/hour),pressurerange,pressurestability(expressedasCV%).减压(稳压)器

SteamPressureReducer-Regulator2021/6/2718控制进入调制器的蒸汽流量.只有物料流量与蒸汽流量同步控制才能实现稳定的制粒作业.

Itmetersthesteamflowgoingintotheconditioningchamber-animportantdeviceforoperator调制器操作与流量应是线性关系. Alinearresponseisrequiredbetweencontrolvalveandsteamflow.一般的控制阀的操作与实际流量不是线性关系. Thegatevalveisnon-linear-athalfopening,smallchangesinsettingresultslargesteamflowvariation.流量控制阀

SteamFlowControlValve

2021/6/2719减压、分水、气压控制三合一

Aseparator-trap-pressureregulator“threeinone”device.流量控制阀在自动和手动控制条件下均与流量呈线性关系. Linearsteamflowcontrolvalvesforbothmanualandautomaticcontrolsystem- CospectValve2021/6/2720蒸汽调制系统参数的设定ParameterSettingsinSteamConditioning考虑因素：调制时间、蒸汽质量、饲料配方.Factorstobeconsidered:Retentiontime,steamqualityandformulation/ingredients.对于一般饲料配方，应在不塞机的前提下，尽可能提高料温.

Ingeneral,mashtemperatureshouldbeconditioned“ashighaspossible”beforereachingthe“chockpoint”.2021/6/2721减压前后的压力比

PressureRatiobefore–afterPressureReducingValve减压可使蒸汽中的水滴挥发.减压幅度过大,在蒸汽质量好时,可形成过热(不饱和)蒸汽.

Pressurereductionhelpswaterdripletsflashoffbutmayalsoproduceasupper-heatedsteamifthepressuredropistoomuchandthesteamqualityalreadyveryhigh.一般推荐:3.5-4:1 GeneralRecommendation:3-4to12021/6/2722进入调制室的蒸汽压力设定

SteamPressureSettingbeforeConditioner调制时间短，蒸汽质量好，宜采用低蒸汽压(1.5-0.5kg/cm2或

更

低)，以争取热交换时间(并降低能耗).

Lowpressure(0.5-1.5kg/cm2)ispreferredifretentiontimeisshort(20secorless).调制时间长，可采用较高蒸汽压力。

Higherpressureworkswell(2-4kg/cm2)ifretentiontimeislong(40secormore).关键在于有足够时间完成热交换-释放潜热.

Thekeyistogivesufficienttimeforheattransfer-releasinglatentheat.2021/6/2723调制温度≤700C以控制水分避免塞机

Keepmashtemperature≤700Ctoavoidmoistureincreasecausedstickiness可考虑采用较高蒸汽压力甚至过热蒸汽

Highersteampressure-lowsteamflow,orsupperheatedsteammayhelp高乳清粉乳猪料蒸汽参数的设定

SteamSettingfor

HighWheyDiet2021/6/2724延长调制时间有助于水分进入并软化粉料以提高颗粒质量

Extendedretentiontimehelpsmoisturepenetrationandsoftensparticlesforbetterpellets.调制时间测定(Measuringmeanretentiontime):

MRT(Sec.)=(3600xW)/(1000xP)where,

W=调制器内水分校正的物料量,kg

Moistureadjustedmashweightinconditioner,kg P=产量,MT/h

Productionrate,MT/h

蒸汽调制时间

RetentionTime2021/6/2725蒸汽调制时间

RetentionTime延长常规调制器调制时间的简易办法: 通过调节浆片角度提高物料在调制器内的充满度.ExtendingRetentionTimebyAdjustingPitchAngle夹层(间接)蒸器的作用

Theroleofindirectsteam.

2021/6/2726ExtendingRetentionTimebyAdjustingPitchAngleMashfillbeforeadjustmentthermometer2021/6/2727ConditionerPaddlePitchAdjustment(TopView)2021/6/2728MashFillafterAdjustment2021/6/2729延长调制时间的设备

多层调制器可变仰角调制器熟化调制器

RipennerDDC2021/6/2730制粒过程的自动控制料流控制蒸汽流控制料温反馈控制，电流反馈控制2021/6/2731常规蒸汽调制的局限性

LimitstoTraditionalSteamConditioning高水分、低温原料限制料温升高。

Cannotachievehighmashtemperaturewheningredientmoistureishighandtemperatureislow.解决途径：烘干-预热？投入机械能?加压调制?Solution:

Drying?

Pre-heating?Mechanicalenergyinput?Pressurizing?

2021/6/2732What’sNew?-ForBetterPellets-2021/6/2733制粒工艺过程的水分控制2021/6/2734控制关键点调制前粉料水分:水分低于12%在混合物机加水(一般不超过一个百分点)调制后水分可通过料温上升估测成品水分:通过冷却时间－料层高度调节2021/6/27352021/6/2736以电容为基础的快速水分测定器：不需样品粉碎不需称量测定误差不超过0.5百分数单位手工操作系统，六秒中得结果,电脑自动监测系统，每秒20个以上读数关键设备2021/6/27372021/6/2738制粒问题解难案例

Pelleting

TroubleShooting-CasebyCaseAnalyses2021/6/2739例1(广东,1985)

Case1(Guangdong)问题:产量偏低,爱环镆寿命低

Problem:lowproductionrate.,diewearingtofast现场观察:进入调制器蒸汽压:2.7kg/cm2,

On-siteobservation:Steampressureatconditioner2.7kg/cm2

问题所在?如何解决?

Solution?2021/6/2740例2(美国,1990)

Case2(US-1990)问题:兔颗粒质量差,含粉多. Problem:poorpelletqualityinarabbitdiet.现场观察:未发现明显异常.与工人座谈得知唯一改变是粉碎玉米由厂外带加工.

Nosignificantproblemfoundinpelletingoperation.Onlychangesrecentlymadewascornmealsuppliedfromtoll-millingbyanoutsidecontractor.

问题所在?如何解决?

Solution?2021/6/2741例3(美国,1994)

Case3(US-1994)问题:料温上不去,颗粒质量差,含粉多,产量低

Problem:Lowmashtemperature,poorpelletquality,lowproductionrate.现场观察:给汽打滑,减压前-后蒸汽压:6.5-2.7,

手可握住疏水阀后水管. Onsiteobservation:surgingwhenaddingsteam;steampressureatboiler:6.5kg/cm,afterconditioner:2.7kg;handscanholdonpipeaftercheckvalve.问题所在?如何解决?

Solution?2021/6/2742例4(江西,1999)

Case2(JiangXi-1999)问题:成品水分.10.5%. Problem:Lowm