脉冲布袋除尘器全参数设计计算表

长袋低压脉冲除尘器选型计算表格,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

处理风量Q(M3/h),滤袋规格Φ㎜,滤袋长度L(㎜),初设风速M/min,初定面积㎡,初定袋数(条）,初定室数,选取室数,选取灰仓数,选取停风阀数,选取上箱体排数,袋底与进气上口距离,确定每箱阀数,确定每阀袋数,阀向袋间净距㎜,选取阀间距㎜,袋向袋间净距㎜,选取袋间距㎜,壁与布袋间净距㎜,壁与布袋中心距㎜,选取卸灰阀尺寸㎜,选取灰斗夹角,初设停风阀Φ(M),选取停风阀Φ(M),初设风道宽度（M）,选取风道宽度（M）,选取风道数,实际袋数,每仓袋数,脉冲阀总数,花板孔数及每箱袋数,全过滤面积㎡,仓过滤面积㎡,室过滤面积㎡,阀过滤面积㎡,全过滤风速M/min,停1仓风速M/min,上箱宽度㎜,上箱长度㎜,灰斗高度1(宽向）,灰斗高度2(长向）,合理灰斗高度㎜,最小中箱高度,进出风法兰高度,单排室数,单排仓数,单仓室数,除尘器总长约(M),除尘器总宽约(M),除尘器总高1约(M),除尘器总高2约(M),除尘器总高约(M),单位重量KG/M2,预估重量约T

1000000,130,6000,1,16667,6805,38,4,2,0,1,0.5,10,18,80,210,80,210,150,215,300,60,#DIV/0!,0,0,0,0,720,360,40,180,1763,882,441,44,9.45,18.90,2320,4580,3629,3642,3641.636823,6100,#DIV/0!,4,2,2,9.28,4.58,12.53,12.54,12.54,28,49

100000,160,6000,1,1667,553,4,4,2,0,1,0.5,10,14,80,240,80,240,150,230,300,60,#DIV/0!,0,0,0,0,560,280,40,140,1688,844,422,42,0.99,1.97,2620,4160,4148,3278,4148.261684,6100,#DIV/0!,4,2,2,10.48,4.16,13.05,12.18,13.05,28,47

500000,160,6000,1,8333,2765,20,20,10,20,2,0.5,10,14,50,210,50,210,150,230,300,60,0.94,0.95,2.5,2.8,1,2800,280,200,140,8440,844,422,42,0.99,1.10,2350,3740,3681,2914,3680.607966,6100,3.45,10,5,2,23.50,10.28,12.58,11.81,12.58,20,169

3000000,130,7000,0.9,55556,19443,98,96,48,48,2,0.5,10,20,70,200,70,200,150,215,300,55,1.49,1.45,3.5,3.8,1,19200,400,960,200,54862,1143,571,57,0.91,0.93,2230,4800,3852,4250,4250.172956,7100,15.10,48,24,2,107.04,13.40,13.75,14.15,14.15,18,988

3000000,160,8000,0.9,55556,13823,24,24,24,48,4,0.5,18,32,90,250,90,250,150,230,300,55,1.49,1.45,3.5,3.8,2,13824,576,432,576,55561,2315,2315,129,0.90,0.94,4710,8510,4164,7814,7813.594801,8100,7.55,6,3,1,28.26,41.64,15.06,18.71,18.71,20,1111

1860000,130,8000,0.95,32632,9993,64,64,16,32,4,1.5,11,14.5,50,180,60,190,150,215,500,50,1.43,1.45,3.5,4,1,10208,638,704,159.5,33335,2083,521,47,0.93,0.99,2230,3325,8707,2949,8706.698097,9100,8.88,16,8,4,35.68,17.30,20.61,14.85,20.61,18,600

1860000,160,8000,0.95,32632,8119,68,64,16,32,4,1.5,9,14,50,210,50,210,150,230,500,50,1.43,1.45,3.5,4,1,8064,504,576,126,32411,2026,506,56,0.96,1.02,2140,3490,8321,3126,8320.686852,9100,8.88,16,8,4,34.24,17.96,20.22,15.03,20.22,18,583

3600000,160,8000,0.95,63158,15714,128,128,32,64,8,3,10,13,50,210,60,220,150,230,500,50,1.41,1.45,3.5,4,2,16640,520,1280,130,66879,2090,522,52,0.90,0.93,2350,3400,9221,3029,9221.379758,10600,8.59,16,8,4,37.60,35.20,22.62,16.43,22.62,18,1204

1000000,130,7600,0.85,19608,6320,32,32,8,16,4,3,11,18,70,200,70,200,150,215,500,55,1.49,1.5,3.6,3.6,1,6336,792,352,198,19656,2457,614,56,0.85,0.97,2430,4160,8568,3443,8567.580286,10200,5.32,8,4,4,19.44,20.24,21.57,16.44,21.57,17,334

1000000,160,8000,0.85,19608,4879,30,32,8,16,4,1,9,17,70,230,60,220,150,230,500,55,1.49,1.5,3.6,3.6,1,4896,612,288,153,19678,2460,615,68,0.85,0.97,2300,4280,8068,3559,8068.124933,8600,5.32,8,4,4,18.40,20.72,19.47,14.96,19.47,17,335

,,框内颜色说明,,,,,,兰字,,主要生成值,,,,,,,必需填定(调整）参数,,,,,,,,,,,根据红色框及具体需要进行调整或不调,,,,,,,,自动生成的参考值,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

"说明：为了方便大家使用，本计算表的各栏目分为黄色、红色、绿色、白色四种。黄色栏目为基本需填写的参数，红色栏目为自动生成的参考值，绿色栏目可要据红色栏或经验填写，白色栏目自动生成的各项参数。其具体的方法如下：

1、先根据需要将风量、布袋规格、布袋长度三个参数进行填写。

2、再根据需要并参照自动生成的过滤风速及自动生成的初定箱室数（上箱体的数量）填写选取箱室数。

3、根据需要的上箱体尺寸及布袋除尘器的尺寸等对脉冲阀及布袋的排列进入修正。经过几次修正就可得到需要的排列。

4、如这时生成的过滤风速超出了需要的范围，初定箱室数有了变化，这时可根据新的初定箱室数从新选取箱室数，直到上箱体尺寸，除尘器尺寸满足设计需要。

5、箱室排列与箱室数的关系：箱室排列目前通行的有1排、2排、四排。选取的箱室数一定要能被排数整除，

6、箱室数与灰斗数：通行的方法有A、一个箱室设一个灰斗；B、两个箱室设一个灰斗；C四个箱室设一个灰斗。灰斗数需为箱室数的整除数，不能有余数，如有余数需对箱室数进行调整。

7、箱室数、灰斗数、停风阀数及尺寸：A、当在线清灰时不设停风阀，停风阀数为0。B、当离线清灰时最少每个灰斗一个停风阀。C、当自动生成的初设停风阀尺寸过大时（>1.2M）时可增加停风阀数，增加停风阀数时按倍数增加。D、停风阀尺寸根据初设尺寸选取，既对初设尺寸进行园整。

8、一般袋底距进风口上口为0.5M，表内此值不需调整。当有特殊要求时如含尘量较大、尘粒较大时及需方有特殊要求时此值需按要求增加，但最好不要大于1.5M。

9、一般袋与袋之间的净间距为50㎜（最小要求），当有具体要求时可对选取袋间距与选取阀向袋间距进行调整直到袋间净距满足要求。

10、一般仓壁与布袋之间的净距为150㎜（最小值）当有具体要求时可对此值进行调整。

11