bmw技术通报01e60e90e87ccc picture offset flickering after programming编程后CCC画面偏移闪烁

1、ViewMeasureCicture编程后CCC闪Releasedate(mm/dd/yy) SCN, CARVehicles影响车ViewMeasureCicture编程后CCC闪Releasedate(mm/dd/yy) SCN, CARVehicles影响车EE60E61E63E64E87 E90 E91 E92Productionperiod(from/to) /Commentonproductionperiod Feedback(allcasesuptheCIDrogrammingand/orflickering：用V22.2DVD(E9x)V23.0DVD22.2（E9X）或23.

2、0（E6X)的版本编程后，CID的画面偏移或闪烁LVDSlineandVehicle equipment concerned: Vehicleswithoption609(Profesalnavigationsystem)onvariousretrofitsarefittedalongtheline(see原因LVDS线路和ntheCCCand受影响的车辆装备：在配609（专业导航系统）的车辆上，装在CCC与CID间线路的所有加装件（见措施）Donot replaceanycheckthevehicleforsoriesfittedntheCCCconverter(LowVoltageDiff

3、erential-ACMRoundsories(completepackageoffront,rearandside措施请不要更换任何零件。请Donot replaceanycheckthevehicleforsoriesfittedntheCCCconverter(LowVoltageDifferential-ACMRoundsories(completepackageoffront,rearandside措施请不要更换任何零件。请检查装在CCC与CID之间的LVDS（低压差分信号）转换器， 。例如：环视系统(车前,车身,车后头)，倒车Maketcontactproblemshavebeen

4、outasIfanLVDSconverterwithpartnumber0406bereplacedwithpartnumber0422isfitted,this确保线路连接故障已被排除。如果安装的LVDS转换器零件号为将其更换成 0422011Iftheproblempersists,proceedas1.ResettheLVDSconverteras0406966，必-Disconnectthe18-pinconnectorfromtheLVDSconverterandthecablefrompinSwitchthe18-pintheignition-Thescreennolongeris

5、offsetbyy 1/3of the-Wait30SwitchofftheDisconnectthe18-pinconnectorandreconnectthecabletoSwitchthe18-pinconnectortotheLVDSis OK again.如果故障持续存在，请按照下列步骤继续：1按照下列步骤重设LVDS转换器从LVDS转换器上拆下 18 脚的连接器，然后把第 13 脚的线断开;重新接上 18脚的连接器。打等30-屏幕不再闪烁，但是画面大约偏移了屏幕的大约 3 分之1关；断开 18脚的连接器，重新把第 13 脚的线连接好；重新把 18 脚的连接器接到LVDS转换器上；打

6、；画面重新回复正常2.IfanACMmodule(partnumber0417 reset as follows:619)fitted,perform-关；断开 18脚的连接器，重新把第 13 脚的线连接好；重新把 18 脚的连接器接到LVDS转换器上；打；画面重新回复正常2.IfanACMmodule(partnumber0417 reset as follows:619)fitted,perform-Disconnectthe26-pinconnectorthecablepinSwitch26-ignition-Thescreennolongerisoffsetbyy 1/3of the-

7、Wait30SwitchofftheDisconnectthe26-pinconnectorandreconnectthecabletoSwitchthe26-pinconnectortotheACMtheisOK2-如果安装了ACM模块（零件0417619），请按照下面步骤进行重设：从ACM单元上断开 26 脚的连接器；断开第12脚的线缆重新连接回 26 脚的连接器打关闭断-30；屏幕不再闪烁，但是画面大约偏移了屏幕的大约 3126 脚的连接器，并重新接回第 12 脚的线缆；重新把26脚的连接器接回到ACM单元；关；画面重新回复正常IfnACMandanLVDSconverterarefitted,aresetmustcarriedoutforeach如果ACM和LVDS转换器两个都安装，每个都得进行重设。FaultlocationNatureDistinct perceptionultition,ition, R Operatesincorrectly,DrivingDriving/Monitor,FrontDistinctMainition, R65Operatesincorrectly,DrivingDriving/Monitor,FrontDistinctMainition, R65Audio