文稿教程工作nakan fat版answer about iat

1、【PI Coater 8 Inspection Report】Anilox着脱繰返精度Q. 動作量 is 1mm, but the real action above is 1.015mm and 1.035mm, Okay for the difference?A. The pure of thischecking repeatability.his meaning, its accuracy is 100%, very good.Regarding difference betn the actual value and setting value, we will do further

2、adjustmensite.Table昇降繰返精度Q. 動作量 is 1.5mm, but the real action above is 1.52mm and 1.51mm, Okay for the difference?A. The pure of thischecking repeatability.his meaning, its accuracy is 100%, very good.Regarding difference betn the actual value and setting value, we will do further adjustmensite.Q. W

3、hat is 印圧補正? What does the unit 1/100 mean?A. 印圧補正 is used in case operator adjust pring quality. 1/100mm is its minimum adjustable unit.Anilox NIPQ. How to measure the anilox NIP, including the operation.A. Measure with scale in 5 different po. When operation, select the NIP.Q. What are 押込前位置and 押込

4、位置?A. Please see the imagehe next page.12012 NAKAN TECHNOs.【PI Coater 8 Inspection Report】押込前位置 and 押込位置Plate CylinderAnAlnoxox Rollelrer押込0点位置 Originalition押込前位置 押込 means pressing. Stand-by押込位置Pressing (production)itionition22012 NAKAN TECHNOs.【PI Coater 8 Inspection Report】Table NIPQ. How to measu

5、re? Including operation.A. Measure with scale in 5 different po.Q. The uniformity is not good, why? and do you have any measure to avoid the uniformity?A. The pure of thischecking the value within certain width.his meaning, its good.Regarding actual prability (surface quality, uniformity etc.), we w

6、ill do further adjustmensite.We also guess APR hasnt been conformed yet becausered not many glasses.版胴振精度Q. What is 振精度? Does it mean the eccentricity (偏度)?A. Yes. Exactly, its eccentricity of roion.Q. How to measure and how to read the data?A. Put a pick tester on the surface of roing plate cylinde

7、r.um and minimum value.The data means difference betnTo keep this accuracy 30m at the site of XMTM, this value must be within 20m Because this accuracy will be decreasing due to transport.he factory.32012 NAKAN TECHNOs.【PI Coater 8 Inspection Report】AR振精度Q. How to measure and how to read the data?A.

8、 Put a pick tester on the surface of roing anilox roller.um and minimum value.The data means difference betnTo keep this accuracy 30m at the site of XMTM, this value must be within 20m Because this accuracy will be decreasing due to transport.he factory.TableQ. How to measure and how to read the dat

9、a?A. Stack 10m height block gauge in layers betn the plate cylinder and the table.The data means distance betn the plate cylinder and the table.Difference ofum value and minimum value is 15m, its very good.Because this accuracy will be decreasing due to transport.予備乾HP表温度Q. Any measure to improve th

10、e temperature uniformity?A. When IAT, we stopped adjustment once temperature uniformity achieved within 5.We will do further adjustmensite.42012 NAKAN TECHNOs.【PI Coater 9 Inspection Report】検査記録表Q. The plate cylinder spec, the size you told us before is 629.831400, but the IAT result is 624.351400,

11、is it OK for this change?A. “P.C.D” is calculated as “diameter of plate cylinder” + “APR cut down *2” (both side).629.83 is P.C.D. not diameter.= 624.35 (diameter of plate cylinder) + 2.74 (APR cut down) *2検査成績表Q. How to measure? What is the tool? Checking method? And how to read this data?A. Put a pick tester on the surface of roing plate cylinder.um and minimum value.The data means difference betnTo keep this accuracy 30m at the