钻井工程师岗位描述_第1页
钻井工程师岗位描述_第2页
钻井工程师岗位描述_第3页
钻井工程师岗位描述_第4页
全文预览已结束

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

1、精选优质文档-倾情为你奉上钻井工程师岗位责任制 Drilling engineers station-responsibility(一) 岗位责任制 Station-responsibility1 负责向平台干部,职工贯彻工程设计,制订与落实各阶段的钻井施工措施和参数,向钻井领班下达每次作业技术指令。1. Drilling engineer is responsible to give publicity to the well project design and formulate the measures and parameters of the drilling constructi

2、on.2 负责钻头的选型及使用分析,负责钻具的管理及下井钻具组合的选配。2. Drilling engineer is responsible to choose the type of bit and bottom hole assemble and analyses the result of the bits application.3 负责指重表、泵压表以及各种工程仪表的使用与管理。3. Drilling engineer is responsible to administrate and make use of drilling engineering instruments.4

3、负责井控设备的定期检查与试压,监督落实井控措施的执行情况,定期组织井控演习。4. Drilling engineer is responsible to check and have pressure test to well control equipment. Besides, Drilling engineer should organize the well control drill.5 严把取芯、井身、固井3大质量关。5.Drilling engineer is responsible to control the quality of the core hole and ceme

4、nting6 负责新技术、新工艺的推广与应用。6. Drilling engineer is responsible to apply and spread the new technology and skill. 7 负责收集、整理、上报各种钻井原始资料,负责填写钻井井史。推7. Drilling engineer is responsible to collect and put the original data in order and report it. Drilling engineer is responsible to compile well records.8 搞好平台

5、钻工的技术教育,以及每口井的技术交底工作。8.Drilling engineer is in charge of drilling technology education and explanation to the floor man 9 负责组织对工程事故调查处理,原因分析,制定预防措施,并向平台经理提出处理意见,经平台经理同意后向技术科汇报。9. Drilling engineer is in charge of investigation of project accident and the analysis of reason, Drilling engineer is resp

6、onsible to formulate the measure to prevention of the accident, and give the advice to manager. Report to technical department after the mangers approval.10 关键作业和复杂作业时必须到现场亲自指挥,做到“五到平台三值班”,即打隔水导管、下套管固井、装井口、起下钻“两头”、测斜、处理井下复杂情况必须到钻台,拖航、油层井段钻进、试油射孔、求产放喷需坚持值班。 10. Drilling engineer must do as a director

7、 when a well occur complicate construction such as conductor drilling, BOP installing, tripping of initial stage, directional well datas survey managing of the complicate situation. Drilling engineer should on duty during the towing, drilling of oil formation, well-test, perforating.11、参加平台旬度检查,对钻井设

8、备的事故隐患要及时组织整改。11. Drilling engineer should take part in the checking of quarter of the year and certificates the potential problem for drilling equipment promptly.12、完成领导交办的临时工作;认真填写“工作日志”。12. Drilling engineer should the finish the job offered by the leader and fill the work log.(二)循回检查线路 Checking

9、route值班房综合录井房钻台下钻具堆场井控装置泥浆泵舱-循环系统钻台上Dog house-log house-drilling floor bottom -drilling pipe yard-well control equipment mud circulating system (三)检查项点 Check points值班房:工程班报表填写工整,齐全;泥浆班报表填写工整,及时。Dog house: check the drilling and mud records filled correctly and promptly.综合录井房:地质岩性变化情况,钻时快慢情况;录井中油气显示井

10、段及级别;钻进中有无异常提示。Log house: observe the change of the character, the display of the oil and gas.钻台下:封井器固定牢靠,合乎标准要求;封井器及管线卫生良好,不漏油、漏泥浆。Bottom of the drilling floor: check the BOP stack fixed firm or not, BOP and the control pipes is clean or not, and dont leak the oil and mud.钻台上:1、检查钻台钻杆立柱编号与录井下井编号是否一

11、致,对应井深与计算数据是否一致;2、死绳固定牢靠,螺丝背帽齐全紧固,防跳螺丝齐全;3、传压器固定良好,灵敏,管线不漏油,冬季用防冻液;4、指重表、泵压表、扭距表等司钻操作台仪表读数准确;5、了解井下情况,作业指令与钻井参数是否匹配合理;6、封井器司控台仪表显示正常,随时可用;7、节流、压井控制台仪表显示正常,随时可用。8、检查节流压井管汇闸门开关位置是否正确,各闸门开关是否灵活。Drilling floor: 1.Check the stand pipes number which is same to number of the log. 2. Check the dead line blo

12、ck fixed well or not. 3. The transformer fixed good, sensitive, not leak of the oil, antifreeze in winter; 4.Weight indicator, pump pressure instrument, torque instrument are accuracy; 5.Understand the down well condition, operating instructions and the drilling parameters match reasonably; 6. Blowo

13、ut preventer control station instrument display normally, available. 7. Throttle, kill the console instrument display normal, ready for use. 8. Check throttling kill manifold valve switch position is correct, all gate switch are flexible.井控装置:1、远程控制台卫生清洁、无油污;2、液压管线接头紧固,不刺、不漏、试压可靠;3、电泵、气泵工作正常;4、控制台、仪

14、表齐全、充压手柄完好,位置正确,各仪表压力在要求范围之内。Well control equipment: 1.Remote control console cleanness without greasy dirty; 2. Hydraulic pipeline joint fastening, no leakage, pressure test and reliable; 3.Electric pump and air pump work condition; 4.Control console and Instrument is complete, charging - the handl

15、e in good condition, correct position, the pressure in the instrument in the required range.钻具堆场:1、到平台钻具按种类不同合理摆放;2、钻具摆放排列整齐;3、检查钻具丝扣清洁,水眼内无杂物;4、备用、上下钻台钻具丝扣戴好护丝;5、不使用的钻具分类打捆,以免误下井。Drilling pipe yard: 1. the drilling pipe arrange reasonably according to the different placement; 2, drilling pipes are

16、putted in order; 3, check the drilling tool thread clean, no debris in the water hole; 4, drilling tool thread should wear thread protector, when them need rise up and down the drilling floor; 5, not used the tools should be bailed classifiably, in order to avoid mistake.循环系统:固控设备正常运转;泥浆液面无异常变化泥浆流动性

17、能良好;储备仓,储备足够泥浆或重泥浆。Mud circulates system: solid control equipment work well .mud tank surface no abnormal changes. Mud condition performance good;, reserve enough heavy mud or mud.四、 岗位风险以及控制措施 Post risks and control measures(一) 岗位风险 Post risks1、 对井下情况调查不清,施工技术措施制定不当,影响施工质量,引发复杂情况和事故;2、 施工技术措施和工艺纪律执

18、行不严,造成质量事故和工程事故;3、 进入油气层、钻遇复杂或高压地层处置不及时或不当,可能发生井喷、井漏、卡钻等工程事故和其他复杂情况;1. To the underground investigation is not clear, improper construction technical measures, affect construction quality, the complex situation and accidents;2. Construction technical measures, execution and process discipline is lax

19、 caused quality accidents and accidents;3. Into the oil and gas layer, the drilling in complex or high pressure formation improper disposal time, may be a blowout, lost circulation and sticking engineering accidents and other complex situations;(二) 控制措施control measures1、 根据项目的地质设计提示,调查邻井地质资料,对高压油气水层

20、和可能含有H2S气体的地层,提出安全施工措施,做好技术交底;2、 审查钻井施工设计中预防井喷、预防H2S气体的措施是否得当;3、 管理井控台账,保证井控设备完好,井控物资储备充足;4、 掌握钻具和井下情况,预防井喷和井下事故;5、 按照HSE现场检查表规定,定期进行检查;6、 严格执行钻具管理制度,负责各种井下工具、钻井工具、套管工具、打捞工具和接头的检查管理和丈量工作;7、 关键作业和复杂作业时必须到现场指挥,做到“五到钻台三值班”,即打隔水导管、下套管固井、装井口、起下钻“两头”、测斜、处理井下复杂情况必须到钻台,油层井段钻进、试油射孔、求产放喷需坚持值班。1. According to

21、the project geological design tips, geological survey of adjacent well data, the high pressure oil and gas layer and formation that may contain H2S gas, safety construction measures are proposed, completes the technical disclosure;2. Review the drilling construction design, to prevent blowout, H2S gas prevention measures are appropriate;3, Manage well control parameter, to guarantee the well control equipment in good condition, well control supplies sufficient reserves;4. Master drilling tools and downhole condition, prevention o

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论