机械图纸英语翻译

1、1， PERMANENTLY MARK PART NUMBER(ALL METHODS ACCEPTABLE)IN LOCATION SHOWN：SAME AS DWG NO.INCLUDING REV & DATE OF MFG 2，REMOVE ALL BURRS AND BREAK ALL EDGES 3，ALL DIMENSIONS AND TOLERANCES APPLY AFTER FINISHING(IF REQUIRED) 4，COSMETIC INSPECTION CLASS IIA-EXTERNAL COMPONENT 5，MATERIAL：LAMINATED 1/

2、2" CORIAN；COLOR SPECIFIED IN PURCHASE ORDER 6，FINISH：LAMINATION TO APPEAR SEAMLESS;NO PITTS OR LINES POST MACHINING：CLEAN & FURTHER SPECIFICATION IN PO 7，POLISHING：IF SPECIFIED IN PO；TOP，SIDES，CHAMFER & 1/2" FROM EDGE ON BASE SURFACE 8，ARTWORK：IF SPECIFIED IN PO；TO BE READ FROM ELL

3、IPTICAL PROFILE 9，PART TO BE MANUFACTURED REFERENCING DWG AND 3D GEOMETRY SUPPLIED2， 1.如图所示的位置上加上耐久的产品编号标记,就是图纸编号包括图纸版本号及生产日期. 2.除去所有毛刺及所有边倒角. 3.(如必要的话)产品表面处理后,所有的尺寸及公差要符合要求. 4.外观检测等级为【信息工业协会美-外观件】 5.产品材料:1/2 英寸厚的"可丽耐"薄板, 颜色在采购单内注明. 6.表面要求:层压后无结合线,无凹坑或凸凹线状, 后处理: 洁净及详细请看采购单说明. 7.表面抛光: 如果在采购

4、单中有说明则按其要求做,否则顶部,侧面,倒角斜面及底边上来1/2英寸处要抛光. 8.美工; 如果在采购单中有说明则按其要求做,否则从椭圆形中来读取(这一点要能与你们专业有关,我就不是很清楚,要看产品图才知) 9.产品加工请参照提供的工程图及三维立体图.Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子 Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查 fit

5、together 组装在一起 fasten 锁紧 (螺丝 ) fixture 夹具 (治具 ) pallet 栈板 barcode 条码 barcode scanner 条码扫描器 fuse together 熔合 fuse machine 热熔机 repair 修理 operator 作业员 QC 品管 supervisor 课长 ME 制造工程师 MT 制造生技 cosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸 EMI gasket 导电条Cooling channels are t

6、o be a minimum of 8 mm in diameter; Use copper plugsl where required; The waterline inlets and outlets should be put on the sidel opposite of the operator; Pipe thread sealing compound is required, 1/4PT;l Waterlines will be in all slides;l Waterlines will be installed inl the stripper plate for coo

7、ling the runner; Venting Blind pocketsl or deep ribs require passive vents or venting channels into blind areas to assure filling without burning; Mold Component Use 89.8mml locating rings and chamfer all sharp corners; “X” type interlock;l l Use 4 guide pins and one guide pins location is offset; H

8、ardness of thel guide pins must be 10 “RC” higher than the guide bushings; Guide pins mustl be at a minimum 15mm longer than longest standing core or horn pin, and the diameter must be above 22mm; Guide pins and bushings must be shouldered;l Shoulders are required on all inserts for positioning or d

9、oweled;l l Thickness of the cavity and core inserts must be above 35 mm; The clampingl plate must be above 40mm; Mold frames must be purchased;l Chamfer alll the sharp corner except specific; Screws for stop device must be withl spring wash; Identification Stamping is to be a minimum of 0.1 mml of d

10、epth and the letters are large enough to be readable; Each plate usedl must be stamped with the type of steel and hardness; The mold supplierl identification should be stamped on the mold base; A plaque is to bel mounted on the top of the mold by being screwing into a pocket, the plaque should be re

11、cessed from the outer mold surface, the plaque should include: mold name, tool manufacturer, Colgate Sanxiao or Vietnam property, date, mold weight, etc; Cavity number should be engraved, and the position should be providedl by Colgate Sanxiao project engineer; Each waterline is to be identified onl

12、 each end of the circuit with a number such as “ IN 1 OUT 1”; Guide pinsl and bushings must be labeled; All “X” type locating bars and pockets mustl be labeled; Texture and surface finish All the A surface will bel finished with an SPI # A2; All the C surface will be finished with an SPIl # B3; EDM

13、Surface Finish ( Charmilles CH Standards Scale );l Surfacel Finish Requirements of specific impression area to be indicated on 2D CAD file drawing or sample; Surface Finish B2 with EDM texture Requirements forl Runner System; Note: Surface finishes base on 420 Stainless Steel materiall with 50 R&quo

14、t;C" Hardness冷却渠道，以最低的八毫米直径; 使用铜插头需要;l 水线口和网点应放在对立面的经营者;l 管螺纹密封胶是需要1/4pt ;l 船只，将在所有的幻灯片;l 船只将被安装在汽提塔钢板冷却亚军;l 宣泄 盲目口袋或深排骨需要被动喷口或宣泄渠道进入盲区，以保证加油站，没有燃烧;l 模具组件 使用89.8毫米定位戒指及倒角所有急弯;l 划" × "型联锁;l 利用4指导引脚和一个引导针的位置是抵销;l 硬度为指导引脚必须10 "钢筋混凝土"高于指导轴套;l 引导引脚必须在最低限度15毫米长于最长的常设核心或角边，与直径

15、必须高于22毫米;l 引导销和衬套必须肩负;l 肩膀上，有必要对所有刀片定位或doweled ;l 厚度腔和核心刀片必须高于35毫米;l 夹紧板必须高于40毫米;l 模框必须购买;l 倒角所有的尖角，除具体;l 螺钉停止装置必须与春季洗手;l 鉴定 冲压，是一个最低的0.1毫米的深度和信件是大到足以被可读性;l 每块板使用，必须加盖类型的钢材和硬度;l 模具供应商确定要盖上就模具基地;l 一牌匾，是安装在顶部的模具被拧成一本袖珍，该牌匾应休会，由外模表面上，该牌匾内容应包括：模具名称，刀具制造商，高露洁三效或越南的财产，日期，模具重量等;l 腔数理应铭刻和立场应该提供的高露洁三效项目工程师;l

16、 每个水线是要确定每月底电路与一些诸如"在1 -出1 " ;l 引导销和衬套必须标记;l 所有的" x "型定位酒吧和口袋必须标记;l 纹理和表面光洁度 所有的水面，将成品与spi的素a2 ;l 所有的c面，将成品与spi的 b3的;l 电火花加工表面光洁度（l charmilles甲烷标准级） ; 表面光洁度要求，具体的印象，是至为表示对二维计算机辅助设计绘图文件或样品;l 表面光洁度b2的与电火花加工纹理要求浇注系统;l 注：表面饰面基地，对420不锈钢材料，与50个住宅" c "类硬度lALL WELDS CONTINUOUS

17、UNLESS OTHERWISE STATED. 未注焊缝均为连续焊ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED 未注焊角高3mm.ALL UNSPECIFIED RADI - R3 未注圆角R3REMOVE ALL BURRS AND SHARP EDGES 棱角倒钝CHANNEL 槽钢RSA 708 角钢 70X70X8M30X1.5 pitch M30X1.5的锥螺纹Tackweld 点焊OD 1/4" outside dimension 1/4"的缩写 外径直1/4"75 CRS 尺寸为75 材质为冷轧钢板410

18、 OPENING REF 410 开口参考尺寸40 REF 尺寸为40参考值2.5" BSP 2.5” 圆锥管螺纹2.5" BSPT HEXAGON 2.5” 六角圆锥管螺纹(即对丝)30x2.5 FLAT BAR 30X2.5 扁钢TYP 2 POSNS 2处11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLYEND COILS SQUARE TO TOUCH.总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明)FEMALE: 内扣(母扣)MALE: 外扣(公扣)偏心轴 eccentric shaft 销轴 PIN开口销 COTTE