n o v a j e t 写 真 机 常 见 问 题（n o v j e t 写 真 机 常 见 问 题）.doc

1、n o v a j e t 写 真 机 常 见 问 题（n o v j e t 写 真 机 常 见 问 题）n o v j e t 写 真 机 常 见 问 题1.错位:a.故障现象: 左右错位大于0.5公分, 隔段错位. 电机阻力值过大.可检查皮带, 皮带轮, 铜套, 滑面贴, 光栅, 确保都没有问题仍不能解决, 更换电机.b.故障现象: 左右错位小于0.5公分, 连续错位.铜套阻力过大, 可清洗铜套, 擦拭光杆或降低托架速度.仍不能解决, 更换铜套c.故障现象: 出图斜, 成平行四边形.擦光栅, 译码器.仍不能解决, 检查光栅如果受损, 更换光栅.d.故障现象: 字体周围有杂色虚边.校准喷头

2、.2.出图乱码:a.故障现象: 固定某个颜色有色块.喷头有问题, 更换喷头.b.故障现象: 整张图上有色块.数据线或者打印线有问题.出图速度慢: 3.故障现象: 打图左右有停顿.操作系统是否min98, 外部并行打印口是否是ecp4.喷头不出墨:a.故障现象: 单个喷头不出墨.交叉换位打清洗后, 判断触点带是否有问题.如无, 可以判断是烧或者堵, 堵的话可用热的纯净水冲泡.如固定一个颜色经常堵头, 可与墨水供应商联系, 调换墨水.b.故障现象: 所有喷头均不出喷墨, 其中有一个喷头有问题, 影响其他.逐个打清洗挑出来即可, 或者墨车板有问题.5.无法联机打印:a.检查蒙泰打印机设置是否正常,

3、端口设置是否是lpt1b.检查解密卡, 打印线是否正常.c.如以上均正常仍无法联机打印, 主板打印口或计算机有问题.6.打印宽度不够?the 纸张已经走偏: 初次上纸的时候尽量上正并用卡纸器卡住.b. 页边留白 未改成 扩展: 进入 设置菜单 纸张选项菜单 页边留白 改为 扩展, 一定要保存, 并选择刚才保存的选项7.打印长度不够?纵轴线不准: 打开 辅助功能菜单 颜色校准菜单 图纸纵 轴线测试 即在纸上起始端开始走纸, t, 打印出两个 字型的图标, 用直尺测量交叉点之间的距离, 将数值改为测量后的结果保存并选择所保存的选项即可.系统默认参数为 83.82cm.8. 机器正常上纸后, 写真机

4、无法打印, 进退纸张的按键无效?机器未检测到纸张: 重新装载打印载体或更换测纸器.9. 打印出的图像歪斜错位或者走弧线?the 光栅太脏: 用棉签蘸酒精擦拭光栅并保持环境卫生或更换光栅.b: 拆除光栅感应器用酒精擦拭或更换光栅感应器 光栅感应器太脏.c: 更换铜环或涂抹无尘机油保持润滑 铜环磨损厉害或太脏.d: 将小车速度调到. 小车运行速度太快 7, 8 为宜 或10.打印时小车两边停顿运行不流畅导致打印速度变慢?the 电脑未设置好ecp打印端:. 电脑重启, 在电脑进行硬件自检时按del键进入coms设置, 进入integrated peripherals功能选项, 将其中的parall

5、el powder mode设置为ecp (注意: 一定要是标准ecp, 而不是epp, spp或ecp / epp), 最后保存并退出bios, 随后, 电脑会重新启动, windows系统自动检测到ecp打印口并为其安装驱动程序, 这时, 您就可以使用ecp打印口所提供的告诉传输性能了.您可以打开 我的电脑 右键 属性 硬件 选项卡 设备管理器 端口 ,If there is a ECP printer port (LTP1), it means that you have set it successfullyB. print line is too long or bad contac

6、t with the machine: replace the print line, the print line should not be too longC. computer does not detect the ECP printer port: replace the motherboard using the Intel Chipset, because only the Intel Chipset can allow windows to recognize the standard ECP print portD. the optical axis is too dirt

7、y: replace copper rings or apply clean oil to keep lubrication11., the output of the image stripe?Nozzle clogging or life span: use ink suction machine to clean nozzle or replace nozzle12., the printing process of breaking ink, but pause or ink after the normal?The connection of the ink supply pipe

8、is loose, especially the air leakage between the nozzle and the pin joint. The nozzle and the pin joint are padded and the air in the ink tube is exhausted13., the printing process of ink or ink leakage phenomenon?A. nozzle and pin leakage: cushion the nozzle and the pin joint, and exhaust the air i

9、n the ink tubeB. spray too much ink: ink in the nozzle in 20ml 30ml is appropriate14., the machine boot normal, but the computer output data does not work, and the panel * does not blinkThe data cable that connects the computer and the photo machine is loose: reconnect the data line and check whethe

10、r the data line pin has bounced or replaced the data line15. print output when prompted invisible ink box information?The decryption card contacts too dirty or loose: the decryption card can be inserted again after cleaning, or the decryption card can be replaced16. after the boot, the LCD screen do

11、es not show or show faint, but the car normal self-testA. LCD connector loose: plug in the connecting line or replaceThe low contrast B. LCD screen: open the 6 set menu 5 user settings 7 LCD brightness contrast to the right17., the LCD screen appears Carriage AXIS failure (car longitudinal axis erro

12、r)Small frame as a whole can not function properly: after the shutdown, hand dragging the car to see if the small frame is connected to the hinge, ink pipe or other debris stuck, check whether the belt with the frame is damaged, check whether the small frame deformation.18., the nozzle does not ink

13、out?A. nozzle burn: replace nozzle B. contact belt damage or bad contact: change contact belt or add proper gasket after contact band19. the machine cannot detect paper or appear Paper Sensor ErrorThe paper sensor is too dirty or damaged or in bad contact: wipe or replace with alcohol or re insert i

14、t20., the printed images appear stained ink or difficult to open, usually manifested in two colors, ink stains each otherA. media is too bad or has been damp: keep medium dry or change the point of medium B. ink quality is too bad: replace ink C. machine ink quantity is too heavy: reduce the amount

15、of ink in the machine21. flying ink or image come out with burrs?A.: unearthed installed ground B. sprinkler and correct contact with bad contact: contact with or in contact with the replacement with appropriate gasket C. machine static area or color without calibration: 1. auxiliary function menu -

16、 calibration menu - Color static menu - Color static area test, print out the test after each of the three lines on the choice of four relative value compared with the neat preservation; 2. auxiliary function menu color calibration menu calibration print test, print out the test strip, the horizonta

17、l and vertical position correction adjustment rule is upward and to the right and left down the value increased, reduce the numerical22. appear Internal Error, shut down?A. parts contact or wear: replace the corresponding partsB. test paper grating sensor or sensor contact is not good: re plug a pap

18、er sensor or grating sensorRoutine maintenance:1, the ambient temperature at room temperature (about 22 degrees Celsius), there is a certain humidity, dust as small as possible.2, regular maintenance of the machine, reducing dust, ink and other effects on the machine,Specific items and time are show

19、n in the following table:Sliding axleDaily wipe, add alcohol with clean cloth or paper towel, prohibit using any Watch OilWipe the cartridge (head of Qing etwee)Wash, remove, rinse and wipe the ink, dont lose it and correct it every weekGrating stripClean every week, observe daily, swab + distilled

20、water or alcohol, wipe up and down, dont take too much effortWith the contact piece of ink ink vehicleDaily inspection to make sure that there is no ink contamination and to prevent excessive alcohol from dissolving the mounting of micro circuits.Note: ENCAD, EASY, KIEAN cleaning solution is recomme

21、nded for cleaning and maintenance.1, note that you cannot use oily ink, oily corrosive ink supply system and ink jet jamming. Original ink is your best choice. Can not use mixed ink.2, can not live plug and print line. Otherwise it will cause damage to the motherboard.3, do not rub the nozzle head, ink can be used without h