ME专有名词.doc

組裝、衝壓、噴漆、塑膠成型等機械專業詞匯20Assembly line組裝線Layout布置圖Conveyer流水線物料板Rivet table拉釘機Rivet gun拉釘槍Screw driver起子Electric screw driver電動起子Pneumatic screw driver氣動起子worktable 工作桌OOBA開箱檢查fit together組裝在一起fasten鎖緊(螺絲)fixture 夾具(治具)pallet棧板barcode條碼barcode scanner條碼掃描器fuse together熔合fuse machine熱熔機repair修理operator作業員QC品管Supervisor 課長ME制造工程師MT製造生技cosmetic inspect外觀檢查inner parts inspect內部檢查thumb screw大頭螺絲lbs鎊inch英寸EMI gasket導電條front plate前板rear plate后板chassis基座bezel panel面板power button電源按鍵reset button重置鍵Hi-pot test of SPS高源高壓測試Voltage switch of SPS電源電壓接柆鍵sheet metal parts 沖件plastic parts塑膠件SOP製造作業程序material check list物料檢查表work cell工作間trolley台車carton紙箱sub-line支線left fork叉車Personnel resource department人力資源部production department生產部門planning department企劃部QC Section品管科stamping factory沖壓廠painting factory烤漆廠molding factory成型廠common equipment常用設備uncoiler and straightener整平機punching machine 沖床robot機械手hydraulic machine油壓機lathe車床planer刨床miller銑床grinder磨床driller鉆床linear cutting線切割electrical sparkle電火花welder電焊機staker=riveting machine鉚合機position職務president董事長general manager總經理special assistant manager特助factory director廠長department director部長deputy manager=vice manager副理section supervisor課長deputy section supervisor=vice section supervisor副課長group leader/supervisor組長line supervisor線長assistant manager助理to move, to carry, to handle搬運be put in storage入庫pack packing包裝to apply oil擦油to file burr 銼毛刺final inspection終檢to connect material接料to reverse material 翻料wet station沾濕台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped報廢scrape .v.刮;削deficient purchase來料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation氧化scratch刮傷dents壓痕defective upsiding down抽芽不良defective to staking鉚合不良embedded lump鑲塊feeding is not in place送料不到位stamping-missing漏沖production capacity生產力education and training教育與訓練proposal improvement提案改善spare parts=buffer備件forklift叉車trailer=long vehicle拖板車compound die合模die locker鎖模器pressure plate=plate pinch壓板bolt螺栓name of a department部門名稱administration/general affairs dept總務部automatic screwdriver電動啟子thickness gauge厚薄規gauge(or jig)治具power wire電源線buzzer蜂鳴器defective product label不良標簽identifying sheet list標示單screwdriver holder起子插座pedal踩踏板stopper阻擋器flow board流水板hydraulic handjack油壓板車forklift叉車pallet棧板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger無名指little finger小指band-aid創可貼industrial alcohol工業酒精alcohol container沾濕台head of screwdriver起子頭sweeper掃把mop拖把vaccum cleaner吸塵器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain鏈條jack升降機production line流水線chain鏈條槽magnetizer加磁器lamp holder燈架to mop the floor拖地to clean the floor掃地to clean a table擦桌子air pipe 氣管packaging tool打包機packaging打包missing part漏件wrong part錯件excessive defects過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合規格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外觀不良slipped screwhead/slippery screw head螺絲滑頭slipped screwhead/slippery screw thread滑手speckle斑點mildewed=moldy=mouldy發霉rust生銹deformation變形burr(金屬)flash(塑件)毛邊poor staking鉚合不良excessive gap間隙過大grease/oil stains油污inclusion雜質painting peel off臟污shrinking/shrinkage縮水mixed color雜色scratch劃傷poor processing 制程不良poor incoming part事件不良fold of packaging belt打包帶折皺painting make-up補漆discoloration羿色water spots水漬polishing/surface processing表面處理exposed metal/bare metal金屬裸露lack of painting烤漆不到位safety安全quality品質delivery deadline交貨期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企劃QC品管die worker模工production, to produce生產equipment設備to start a press開機stop/switch off a press關機classification整理regulation整頓cleanness清掃conservation清潔culture教養qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste廢料board看板feeder送料機sliding rack滑料架defective product box不良品箱die change 換模to fix a die裝模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket膠筐isolating plate baffle plate; barricade隔板carton box紙箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines壓線to compress, compressing壓縮character die字模to feed, feeding送料transportation運輸(be)qualified, up to grade合格not up to grade, not qualified不合格material change, stock change材料變更feature change 特性變更evaluation評估prepare for, make preparations for 準備parameters參數rotating speed, revolution轉速manufacture management製造管理abnormal handling異常處理production unit生產單位lots of production生產批量steel plate鋼板roll material捲料manufacture procedure制程operation procedure作業流程to revise, modify修訂to switch over to, switch-to throw-over switching over切換engineering, project difficulty工程瓶頸stage die工程模automation自動化to stake, staking, riveting鉚合add lubricating oil加潤滑油shut die架模shut height of a die架模高度analog-mode device類模器die lifter舉模器argon welding氬焊Vocabulary for stamping衝壓常詞匯stamping, press沖壓punch press, dieing out press沖床uncoiler & straightener整平機feeder送料機rack, shelf, stack料架cylinder油缸robot機械手taker取料機conveyer belt輸送帶transmission rack輸送架top stop上死點bottom stop下死點one stroke一行程inch寸動to continue, cont.連動to grip(material)吸料location lump, locating piece, block stop 定位塊reset復位smoothly順利dent壓痕scratch刮傷deformation變形filings鐵削to draw holes抽孔inquiry, search for查尋to stock, storage, in stock庫存receive領取approval examine and verify審核processing, to process加工delivery, to deliver 交貨To return delivery to. to send delivery back to return of goods退貨registration登記registration card登記卡to control管制to put forward and hand in提報safe stock安全庫存acceptance = receive驗收to notice通知application form for purchase請購單consume, consumption消耗to fill in填寫abrasion磨損reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics統計demand and supply需求career card履歷卡to take apart a die卸下模具to load a die裝上模具to tight a bolt擰緊螺栓to looser a bolt擰鬆螺栓to move away a die plate移走模板easily damaged parts易損件standard parts標準件Breaking.(be)broken,(be)cracked 斷裂to lubricate潤滑common vocabulary for die engineering模具工程常用詞匯die 模具figure file, chart file圖檔cutting die, blanking die沖裁模Progressive die, follow (-on) die連續模compound die復合模punched hole沖孔panel board鑲塊to cut edges=side cut=side scrap切邊to bending折彎to pull, to stretch拉伸Line stretching, line pulling線拉伸engraving, to engrave刻印upsiding down edges翻邊to stake鉚合designing, to design設計design modification設計變化die block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate, front board模板padding block墊塊stepping bar墊條upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上墊板spare dies模具備品spring 彈簧bolt螺栓document folder文件夾file folder資料夾to put file in order整理資料spare tools location手工備品倉first count初盤人first check初盤復櫂人second count 復盤人second check復盤復核人equipment設備waste materials廢料work in progress product在制品casing = containerization裝箱quantity of physical inventory second count 復盤點數量Quantity of customs count會計師盤,點數量the first page第一聯filed by accounting department for reference會計部存查end-user/using unit(department)使用單位Summary of year-end physical inventory bills年終盤點截止單據匯總表bill name單據名稱This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表請與盤點清冊一起送會計部(NHK廠區送財會部)Application status records of year-end physical inventory List and physical inventory card 年終盤點卡與清冊使用狀況明細表Blank and waste sheet NO.空白與作廢單號plate電鍍mold成型material for engineering mold testing工程試模材料not included in physical inventory不列入盤點sample樣品incoming material to be inspected進貨待驗description品名steel/rolled steel鋼材Material statistics sheet物料統計明細表meeting minutes會議記錄meeting type 會別distribution department分發單位location地點chairman主席present members出席人員subject主題conclusion結論decision items決議事項responsible department負責單位pre-fixed finishing date預定完成日approved by / checked by / prepared by核準/審核/承辦PCE assembly production schedule sheet PCE組裝廠生產排配表model機鍾work order工令revision版次remark備注production control confirmation生產確認checked by初審approved by核準department部門Stock age analysis sheet庫存貨齡分析表on-hand inventory現有庫存available material良品可使用obsolete material良品已呆滯to be inspected or reworked待驗或重工total合計cause description原因說明part number/ P/N 料號type形態item/group/class類別quality品質prepared by制表notes說明Year-end physical inventory difference analysis sheet年終盤點差異分析表physical inventory盤點數量physical count quantity帳面數量difference quantity差異量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫on way location在途倉oversea location海外倉spare parts physical inventory list備品盤點清單spare molds location模具備品倉skid/pallet棧板wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score=groove壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head挂鉤槽slug hole廢料孔feature die公母模expansion dwg展開圖radius半徑shim(wedge)楔子torch-flame cut火焰切割set screw止付螺絲form block折刀stop pin定位銷round pierce punch=die button圓沖子shape punch=die insert異形子stock locater block定位塊under cut=scrap chopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板bushing block襯套insert 入塊club car高爾夫球車capability能力parameter參數factor系數phosphate皮膜化成viscosity涂料粘度alkali dipping脫脂(浸鹼去油脂)main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料degrease脫脂rinse水洗alkaline etch齡咬de-smut剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次part number/P/N料號good products良品scraped products報放心品defective products不良品finished products成品disposed products處理品barcode條碼flow chart流程表單assembly組裝stamping沖壓molding成型spare parts=buffer備品coordinate座標dismantle the die折模auxiliary function輔助功能poly-line多義線heater band 加熱片thermocouple熱電偶sand blasting噴沙grit 砂礫de-rusting machine除銹機de-gate打澆口dryer烘干機induction感應induction light感應光response=reaction=interaction感應ram連杆edge finder巡邊器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕de-lamination起鱗cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線patent專利grit沙礫granule=grain細粒grit maker抽粒機cushion緩沖magnalium鎂鋁合金magnesium鎂金metal plate鈑金lathe車mill銼plane鉋grind磨drill鑽boring鏜blister氣泡fillet鑲;嵌邊through-hole form通孔形式roller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸angular offset角度偏差velocity速度production tempo生產進度現狀torque扭矩spline=the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel鎢高速的moly high speed steel鉬高速的organic solvent有機溶劑bracket小磁導liaison聯絡單volatile揮發性resistance電阻ion離子titrator滴定儀beacon警示燈coolant冷卻液crusher破碎機模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模gang dies複合模shearing die剪邊模riveting die鉚合模pierce沖孔forming成型(抽凸,沖凸)draw hole抽孔bending折彎trim切邊emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線blanking下料stamp letter沖字(料號)shearing剪斷tick-mark nearside正面壓印tick-mark farside反面壓印沖壓名稱類extension dwg展開圖procedure dwg工程圖die structure dwg模具結構圖material材質material thickness料片厚度factor系數upward向上downward向下press specification沖床規格die height range適用模高die height閉模高度burr毛邊gap間隙weight重量total wt.總重量punch wt.上模重量五金零件類inner guiding post內導柱inner hexagon screw內六角螺釘dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves=spool等高套筒pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套模板類top plate上托板（頂板）top block上墊腳punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板)stripping plate內外打(脫料板)outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板零件類punch沖頭insert入塊(嵌入件)de-burring punch壓毛邊沖子groove punch壓線沖子stamped punch字模沖子round punch圓沖子special shape punch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊Supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂桿trimming punch切邊沖子stiffening rib punch = stinger 加強筋衝子ribbon punch壓筋沖子reel-stretch punch卷圓壓平沖子guide plate定位板sliding block滑塊sliding dowel block滑塊固定塊active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂桿spring-box eject-plate彈簧箱頂板bushing block襯套cover plate蓋板guide pad導料塊塑件&模具相關英文compression molding壓縮成型 flash mold溢流式模具 positive mold擠壓式模具 split mold分割式模具cavity型控 母模core模心 公模taper錐拔leather cloak倣皮革shiver飾紋flow mark流痕welding mark溶合痕post screw insert螺紋套筒埋值self tapping screw自攻螺絲striper plate脫料板piston活塞cylinder汽缸套chip細碎物handle mold手持式模具移轉成型用模具encapsulation molding低壓封裝成型射出成型用模具two plate兩極式（模具）well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道h=0.020.05mmw=3.2mmL=35mmwelding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleave套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料板guide pin導銷eject rod (bar)（成型機）頂業捧subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向squirt gate射料澆口，直澆口nozzle射嘴squirt lock pin料頭鉤銷(拉料杆)slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口H=F=1/2t1/5tT=2.53.5mmdiaphragm gate隔膜澆口ring gate環形澆口submarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口0.81.0mmRunner less無澆道 (squirt less)無射料管方式long nozzle延長噴嘴方式品質人員名稱類QC quality control品質管理人員FQCfinal quality control終點品質管制人員IPQCin process quality control制程中的品質管制人員OQCoutput quality control最終出貨品質管制人員IQCincoming quality control進料品質管制人員TQCtotal quality control全面質量管理POCpassage quality control段檢人員QAquality assurance質量保證人員OQAoutput quality assurance出貨質量保證人員QEquality engineering品質工程人員品質保證類FAIfirst article inspection新品首件檢查FAAfirst article assurance首件確認TVRtool verification report模具確認報告3B3B (3 tooling booking items)模具正式投產前確認(壓力、溫度/油,水、料)CPcapability index能力指數CPKcapability index of process模具製程能力參數SSQAstandardized supplier quality合格供應商品質評估OOBAout of box audit開箱檢查QFDquality function deployment品質機能展開FMEAfailure model effectiveness analysis失效模式分析8D8 disciplines8項回覆內容FAfinal audit最後一次稽核CARcorrective action request改正行動要求corrective action report改正行動報告FQC運作類AQLAcceptable Quality Level運作類允收品質水準S/SSample size抽樣檢驗樣本大小ACCAccept允收REEReject拒收CRCritical極嚴重的MAJMajor主要的MINMinor輕微的AOQAverage Output Quality平均出廠品質AOQLAverage Output Quality Level平均出廠品質Q/R/SQuality/Reliability/Service品質/可靠度服務MIL-STDMilitary-Standard軍用標準S I-S IVSpecial I-Special IV特殊抽樣水準等級P/NPart Number料號L/N Lot Number特采AODAccept On Deviation特采UAIUse As It首件檢查報告FPIRFirst Piece Inspection Report百萬分之一PPMPercent Per Million批號制程統計品管專類SPCStatistical Process Control統計製程管制SQCStatistical Quality Control統計品質管制RRange全距ARAverage Range全距平均值UCLUpper Central Limit管制上限LCLLower Central Limit管制下限MAXMaximum最大值MINMinimum最小值GRRGauge Reproducibility & Repeatability量具之再制性及重測性判斷量可靠與否DIMDimension尺寸DIADiameter直徑FREQFrequency頻率NNumber樣品數其它品質術語類QCCQuality Control Circle品質圈QITQuality Improvement Team品質改善小組PDCAPlan Do Check Action計劃 執行 檢查 總結ZDZero Defect零缺點QIQuality Improvement品質改善QPQuality Policy目標方針TQMTotal Quality Management全面品質管理MRBMaterial Reject Bill退貨單LQLLimiting Quality Level最低品質水準RMAReturn Material Audit退料認可QANQuality Ameliorate Notice品質改善活動ADMAbsolute Dimension Measurement全尺寸測量QTQuality Target品質目標7QCTools7 Quality Controll Tools品管七大手法通用之件類ECNEngineering Change Notes工程變更通知(供應商)ECOEngineering Change Order工程改動要求(客戶)PCNProcess Change Notice工序改動通知PMPProduct Management Plan生產管制計劃SIPSpecification In Process製程檢驗規格SOPStandard Operation Procedure製造作業規範ISInspection Specification成品檢驗規範BOMBill Of Material物料清單PSPackage Specification包裝規範SPECSpecification規格DWGDrawing圖面系統文件類QCQuality System品質系統ESEngineering Standardization工程標準CGOOChina GeneralPCE龍華廠文件HHuston(美國)休斯敦CCompaq(美國)康伯公司CChina中國大陸AAssembly組裝(廠)SStamping沖壓(廠)PPainting烤漆(廠)IIntel英特爾公司TTAIWAN臺灣IWSInternational Workman Standard工藝標準ISOInternational Standard Organization國際標準化組織GSGeneral Specifica