csful测量报告1模板

ProjectName :CS11 CS11_FullymeasuredReport

PartNumber 8888366445

CADNumber :8888366382_003

ProductName :PATCHWINDSCREENMEMBERUPPERRH

Supplier :上海天轼

VCCMaterialstandards:VDA239-CR300LAActualMaterial:CR300LA

Thickness :1.6mmCoatingthickness:N/ADetectiontime:2016/07/06

CHECKRESULT检查结果

CHECKDATE

检测日期

OK.RATIO合格率

Partcode

P1

P2

P3

TOTAL

全尺寸合格率

OKRatio

100%

OKPoints

72

TotalPoints

72

SURF.

型面合格率

OKRatio

100%

OKPoints

44

TotalPoints

44

TRIM

修边合格率

OKRatio

100%

OKPoints

24

TotalPoints

24

OKRatio

100%

HOLE

孔位孔径合格率

OKPoints

4

TotalPoints

4

RPSInformation

X5

Y4/X6

,Z3

Z1

Z2

Z4

Step1:SureaceChecking

第1页

第2页

Step2:TrimChecking

第3页

Step3:HolesPosition

第4页

第5页

Step4:HolesizeChecking

nominal

8.1

(0～0.15)

8.1*10

(0～0.15)

(-0.5～0.5)

actual

8.16

8.17*10.04

deviation

0

0

nominal

actual

deviation

RPS1

RPS2

Step5:Thinning

REPORTCHECKINGTHINNES

Measurethicknessrequest:

mm

actualthickness

mm

LIMITSMAX:20%

1

1.52

5

6

1

2

3

4

2

1.44

3

1.45

4

1.51

5

1.42

6

1.41

7

8

9

10

11

12

13

14

15

16

THINNINGMAX

1.41

Step6:AppearanceChecking

AppearanceChecking外观检查

NO

判定标准

Controlstandard

检验方法

Methond

判定

OK、NG、N/A

Picture

1

零件是否正确？

Visual

OK

Istherigntpart?

目视

2

变薄率是否 料厚 20%范 内

THINNINGMAXnomore20%

Venirecaliper游标卡

OK

尺

3

是否有开裂、暗裂？

Visual

OK

Nocrack,deformation

目视

4

毛边、毛刺、尖角是否 0.3mm范围

Venirecaliper游标卡

OK

内？glitches,indentation,damaged,

尺

5

是否有模痕、压伤（无手感可接受）？

withthehand

NG

Noroughnessdetectwiththehand

6

是否有拉伤、划伤？

手触withthe

NG

Nodegradationordeformation

hand

7

是否有起皱、变形（装配面平面度需

0.2MM以内）？Nocrack,deformation

Visual/Venirecaliper

目视/游标卡尺

OK

8

是否有生锈？Rust?

Visual

OK

目视

9

字印是否正确、明显且反面无手感？Markinginformationcrrect?

Visual/withthehand

目视/手触

NG

10

报告公差是否与3D公差相符？

检查checking

OK

Reporttoleranceisthesamewith3D?

11

零件定位是否与检具定义相符？

检具gauge

OK

PRSisthesamewithgauge?

12

料边断差是否超过公差带的50%？

Trimnomorethan50%outoft