T汽车吊性能表

#/3100T主要性能与参数数值数值100000kg3238kN.m1127kN.m48m62.1m14550口2750口3750mm12.8-48m18.1m项目最大额定总起重量基本臂最大起重力矩最长主臂+副臂最大起重力矩主臂最大起升高度主臂+副臂最大起升高度外形尺寸(□□□□□ )主臂长副臂长

起重特性表PATEDLIFTINGCAPACITYTABLE单位（UNIT）：Kg工作幅度WORKINGRADIUS(m)主 臂支腿全伸、后方、侧方作业REAR&SIDEWORKINGAREAWITHOUTRIGGERFULLYEXTENDED主臂仰角BOOMANGLE(□)主臂+副臂45+9.5mBOOM+JIB45+16.0m臂 长口臂安装角JIBOFFSET口臂安装角JIBOFFSET12口0m16口2m20口4m27口0m33口0m39口0m45口0m5°30°5°30°3.0100000700008060002500400013003.59200070000580007855002400360012004.08500070000540007650002300320011504.5760006400051000350007445002200300011005.0700005800049000350007240002100270010505.563000510004500035000260007037002050250010006.05700046000430003400026000683400195024009506.5480004300041000330002600020000663200190022009007.0440004000039000320002600020000642900185021008507.537000370003500030500250002000015000622400180018008008.03400034000320002900040001900015000602000175015007509.0270002700027000250002250017500150005816001500120070010.02190021900022000205001650015000561400135011.018400190001950018000155001400012.015700160001650016000145001360014.01160001280013500130001200016.08400980010500110001050018.06300780082008500900020.0600066007200750022.0500052005800620024.042004800520026.03800430028.03100360030.02900说明（NOTE）：以上作业工况均为支腿全伸，不允许在不打支腿的情况下吊重。 (Aboveworkingconditionisallwithoutriggerfullyextended,neverliftaloadonthewheels.)表中粗线以上数值是由起重机的结构强度所决定的，粗线以下数值是由起重机整机稳定性所决定的。(Capacitiesabovethethicklineinthetablearebasedontheboomstrength,theothers,onstablitiyofthecompletemachine.)打好第五支腿时，表中数值适用于圆周 360°作业。 (Withthe5thoutriggerfullyextended,full360rotationisavailableaccordingtothevalueslistedintheabovetable.)表中所列额定起重量为最大允许口，并包括吊口重量( 100吨吊钩重815Kg,60吨吊钩重560Kg,6吨吊钩重 180Kg)和其他吊具的重量。 (Theratedliftingcapacitylistedinthetableismax.allowedvalue,includingweightofthehookblock(thehookblockweightis815kgfor100t,560kgfor60t,180kgfor6t)andotherslings.)表中所给幅度值，是指吊载后吊钩中心到回转中心的水平距离。 (Aworkingradiusgiveninthetableisahorizontaltotheaxisoftheslewingringwhenthehookblockisloaded.)当实际臂长和工作幅度在两数值之间时，应按最大臂长和幅度值确定起重量。 (Whenactualboomlengthisbetweentwovalues,determingliftingcapacityaccordingtobiggerboomandradius.)在副臂伸出的情况下使用主臂作业时， 额定起重量不仅要扣除吊具的重量， 还要扣除