TPS真金板施工方案

目 录

················································································································

·········································································································································9

·········································································································································9

·····················································································································9

···································································································································10

·····································································································

!

···············································································································································12

·····································································

!

···································································································································12

···············································································································13

·················································································································12

·······································································································

·····························································································

·····························································································

·······································································································

2.2《民用建筑热工设计规范》GB50176-932.3《公共建筑节能设计标准》GB50189-20052.4《建筑工程施工质量验收统一标准》GB50300-20112.5《外墙外保温工程技术规程》JG144-20042.6《膨胀聚苯板薄抹灰外墙外保温系统》JG149-20032.8《建筑涂饰工程施工及验收规程》JGJ/T29-20032.9《采暖居住建筑节能检验标准》JGJ132-2001(J85-2001)2.10《夏热冬冷地区居住建筑节能设计标准》JGJ134-2001(J116-2001)2.11《上海市民用建筑节能工程施工质量验收规范》（DGJ32/22-2006）

性应用标准)

项 目耐候性抗风压吸水量抗冲击性

性

能

指

标表面无裂缝、空鼓、剥落、起泡现象。抹面层和保温层的拉伸粘结强度不小于0.10MPa。系统在水中浸泡

1h

后的吸水量≤500g/m建筑物首层以下墙面：10J

级；建筑物二层以上墙面：3J

级

试

验

方

法JGJ

144JGJ

144JGJ149JGJ

14410

次冻融循环后，系统无空鼓、脱落，无渗水裂缝；抹面层、保温层的拉伸粘结强度不小于0.10MPa，破坏耐冻融 JGJ抹面层、保温层的拉伸粘结强度不小于0.10MPa，破坏界面应位于保温层内。水蒸气湿流密度 ≥1.67g/m2·h抹面层不透水性 2h

试样内侧无水渗透

JG

149JGJ

144

10%)，MPa垂直于板面方向的抗拉强度，MPa

吸水率(体积分数)，%

A级

MPa（与水泥砂MPa（与改性聚

拉伸粘结强度，MPa

向），％

含量为(14.5±0.8)%，

含量≥16.0%

冻融循环（5

50mm，无裂纹

GB50210-2011《建筑装饰装修工程

JGJ63-89。

硅酸盐水泥:中细砂:胶:水＝1:3:0.3:适量（重量比）。

施工时用手持式电动搅拌机搅拌，拌制的粘结砂浆重量比为水:砂浆=1:5，边加水边搅

200mm。

据，在门窗洞口部位的真金板，不允许用碎板拼凑，需用整幅板切割，裁成“L”型进行铺贴，

粘贴真金板时，板缝应挤紧，相邻板应齐平，施工时控制板间缝隙不得大于2mm，板间

220mm、厚为实际粘贴厚度

1.2～1.3

结宽度≥80mm，且翻包网格布本身不得出现搭接（目的是避免面层大面施工时在此部位出现三

100%，严禁出现干搭接。

80mm，用网格布和粘

200mm。

300mm，防止结构沉降引起保温系统破坏。

墙体基层应符合《建筑装饰装修工程质量验收规程》（GB50210-2011）中一般抹灰工

目应符合《上海市民