液晶显示器行业内中英文对照表

1、液晶显示器行业内中英文对照 表附：缩略语中英文对照表AACFAnisotropic Conductive Film各向异性导电薄膜ADCAnalog-Digital Converter模数转换器AESAuger Electron Spectrometer俄歇电子能谱仪AFFSAdvanced FFSAFLC Anti-Ferroelectric Liquid Crystal反铁电液晶AMLCDActive Matrix Liquid CrystalDisplay有源矩阵液晶显示器件AMOLEDActive Matrix Organic LightEmitting Display有源矩阵有机电致

2、发光二极管APCVDAtmospheric Pressure ChemicalVapor Deposition常压化学气相沉积AP Plasma Atmospheric Pressure Plasma常压等离子清洗AQK Aqua Knife水刀清洗a-Si Amorphous Silicon非晶硅AS-IPS Advanced-Super-In-Plane Switching超高级面内切换宽视角技术BBCEBack Channel Etched背沟道刻蚀型BEFBrightness Enhancement Film增亮膜BEW Blurred Edge width边界模糊区域宽度B/L Ba

3、ck Light背光源BM Black Matrix黑 色矩阵或黑矩阵BSBack Channel Stop背沟道保护型BJBubble Jet气泡 清洗方法，又被称为CJCCCD Charge Coupled Device电荷耦合器件CCFL Cold Cathode Fluorescent Lamp (Light )冷阴极荧光灯CDCritical Dimension显影后或刻蚀后的图形尺寸CFColor Filter彩色滤光片CFIColor Filter Integration彩色滤光片集成CIE Commission Internationale de lEclairage国际照明委

4、员会CJ Cabitation Jet用力口了高压的去离子水与空气混合后所产生的大量 气泡来去除灰尘的一种清洗方法COA Color Filter on Array阵列上彩色滤光片COFChip On Film薄膜芯片集成COGChip On Glass玻璃芯片集成COP Cycio Olefins Polymer环烯胫聚合物CRTCathode Ray Tube阴极射线管CVDChemical Vapor Deposition化学气相沉积CSTN Color STN彩色超扭曲向列型DDAPDepth AES Profiles俄歇深度剖面分析D.C.Direct Current直流DICD D

5、evelopment Inspection CD显影后光刻胶之间的间距DI waterDeionized water去离子水DLDSDynamical LowDiscrepancySequences网点图案生成方法DLPDigital Light Processing数字光处理器DMDDigital Micromirror DeviceDRCR数字微镜装置DRCRContrast Ratio in Dark Room暗室对比度ECRElectron Cyclotron Resonance电子回旋ECRElectron Cyclotron Resonance电子回旋共振刻蚀EMIElectro

6、Magnetic Interference电磁干扰EMLEmission layer发 光层EPD End Point Detection刻蚀结束点的测量EPDElectronic Paper Display电子纸张显示器件ESREnhanced Specular Reflector光学增强反射膜ETLElectron transport layer电子传输层FFEDField Emitting Display场致发射显示器FFDFeed Forward Drive过驱动FFL Flat Fluorescent Lamp平面荧光灯FFSFringe Field Switching边缘场转换宽视

7、角技术FICDFinal Inspection CD刻蚀完成后被刻物质外观图形间距测试得到的尺FLC Ferroelectric Liquid Crystal铁电液晶FPDM Flat Panel Display Measurements平板显示测量方法FSC Field-Sequential Color场序彩色GHHTLHole transport layer空穴传输层HTPSHigh Temperate Polycrystal Silicon局温多晶硅IIC Integrate Circuit集成电路ICMIllumination and Color Management照明色彩管理IEC

8、International Electrical Commission国际电工委员会 TOC o 1-5 h z ILBInner Lead Bonding内引线焊接IPSIn-Plane Switching面内切换宽视角技术IRInfrared Ray远红外线ISInverted Staggered反交叠结构ISO International Organization forStandardization国际标准化组织ITO Indium Tin Oxide锡掺杂氧化锢薄膜JLLCOSLiquid Crystal On Silicon硅基液晶（液晶反射式）LCDLiquid Crystal

9、Display液晶显示器LDDLightly Doped Drain微掺杂沟道型LDSLow Discrepancy Sequences超均匀分布列理论LED Light Emitting Diode发光二极管LGPLight Guide Plate导光板LMDLight Measurement DeviceVaporBeam光学测试仪器VaporBeamLPCVDLow PressureChemicalDeposition低压化学气相沉积LP-MBELow PressureMolecularEpitaxy低压分子束外延LRCR Contrast Ratio in Lighted Room亮室

10、对比度LTPSLow Temperate Polycrystal Silicon低温多晶硅LVDSlow Voltage Differential Signaling低压差分信号MMCU Micro Control Unit微控制单元MOS-FET Metal Oxide Silicon -Field EffectTransistor金属-氧化物-硅场效应晶体管MPRT Moving Picture Response Time运动图象响应速度MS Mega SonicMHz的超声波清洗方法MVA Multi-domain Vertical Alignment多畴垂直取向NNB Notebook

11、笔记本电脑NS Normal Staggered正交叠结构NTSC National Television SystemCommittee国际电视系统委员会OOCB Optical Compensated Bending光学补偿弯曲宽视角技术ODFOne Drop Filling液晶滴注OLBOuter Lead Bonding夕卜部引线连接OLED Organic Light Emitting Display有机电致发光二极管OSD On Screen Display屏幕菜单式调节PPAD焊接衬垫PCB Print Circuit BoardBp刷电路板PDA Personal Digita

12、l Assistant个人数字处理机PDPPlasma Display Panel等离子体显示屏PEPlasma Etching等离子体刻蚀PECVD Plasma Enhanced Chemical VaporDeposition等离子体增强化学气相沉积PEPPhoto Engraving Process光刻工艺PIPolyimide聚酰亚胺取向层PLED Polymer Light Emitting Diode高分子有机电致发光显示器PMMA Polymethyl Methacrylate聚甲基丙烯酸甲酯POLPolarizer偏振片PRPhoto Resist光 亥 U胶p-SiPoly

13、crystal Silicon(Polysilicon)多晶硅PVAPatterned Vertical Alignment垂直取向构型PVA Polyvinyl Alcohol聚乙烯醇PWM Pulse width modulation脉冲宽度调制QQVGA Quarter Video Graphics Array1/4视频圆形阵列（240X320象素）RRB Roll BRUSH辐品 URF Radio Frequency射频RF Power Radio Frequency Power射频功率RGB Red Green Blue红绿蓝RIEReactive Ion Etching反应离子刻

14、蚀SEMSSEMScanning Electron Microscope扫描电子显微镜SEMI Semiconductor Equipment andMaterials International国际半导体设备与材料 协会SID Society for Information Display信息显示协会S-IPS Super- In-Plane Switching超级面内切换宽视角技术SMDSurface Mounted Device表面贴装器件 TOC o 1-5 h z SOCSystem On Chip芯片上系统SOGSystem On Glass玻璃上系统SOPSystem On Pa

15、nel屏上系统SPCSolid Phase Crystallization固相晶化法SPWGStandard Panel Working Group屏标准化工作组SSFLCSurface Stabilized FerroelectricLiquid Crystal表面稳定化双稳态模式STN Super Twisted Nematic超扭曲向列型SW Shower喷淋清洗TTAB Tape Automated Bonding带载自动连接TAC Triacetyl Cellulose三醋酸纤维素TCON Timing Controller时序控制器TCPTape Carrier Package带载

16、封装TEMTransmission Electron Microscope透射电子显微镜TFT-LCD Thin Film Transistor LiquidCrystal Display薄膜晶体管液晶显示器TMDSTransition Minimized DifferentialSignaling最小化传输差分信号TN Twisted Nematic扭曲向列型UUS UltraSonic超 声波清洗UV UltraViolet lamp紫外灯清洗VVA Vertical Alignment垂直取向VESA Video Electronics StandardsAssociation视频电子标

17、准协会WWB Wire Bonding线连接XXPS X-ray Photoelectron SpectromX射线光电子能谱分析工业常用的英文缩写 品质人员名称类QC quality control品质管理人员FQC final quality control 终点质量管理人 贝IPQC in process quality control 制程中的 质量管理人员OQC output quality control 最终出货质量 管理人员IQC incoming quality control 进料质量管 理人员TQC total quality control 全面质量管理 POC pas

18、sage quality control 段检人员 QA quality assurance质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering品质工程人员品质保证类FAI first article inspection新品首件检查FAA first article assurance 首件确认CP capability index 能力指数媵CPK capability process index 模具制程能 力参数SSQA standardized supplier quality audit合格供货商品质评估

19、FMEA failure model effectiveness analysi s失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收 品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major主要的MIN Minor轻微的Q/R/S Quality/Reliability/Service品质 /可靠度/服务P/N Part Number 料号稿L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As I

20、t 特采FPIR First Piece Inspection Report 首件 检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程 管制SQC Statistical Quality Control 统计质量 管理GRR Gauge Reproductiveness & Repeata bility量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number样品数其它品质术语类QIT Quality Improvement Team 品

21、质改 善小组ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质 管理RMA Return Material Audit 退料认可 7QCTools 7 Quality Control Tools 品管七 大手法通用之件类ECN Engineering Change Notice 工程变 更通知（供货商）ECO Engineering Change Order 工程改动 要求（客户）PCN Process Change Notice 工序改动通知

22、PMP Product Management Plan 生产管制 计戈ISIP Standard Inspection Procedure 制程 检验标准程序SOP Standard Operation Procedure 制造 作业规范IS InspectionSpecificationIS InspectionSpecification成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准I

23、WS InternationalWorkman Standard 工艺标准ISO InternationalStandard Organization国际标准化组织GS General Specification一般规格部类PMC Production & Material Control 生产 和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控 制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 品质工程（部）Q

24、A Quality Assurance品质保证（处）QC Quality Control 质量管理（课）PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering工业工程R&D Research & Design 设计开发部生产类PCs Pieces个（根,块等）PRS Pairs 双（对等）CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code生产日期码ID/C Identificat

25、ion Code （供货商）识别码SWR Special Work Request 特殊工作需 求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原 设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output输入/

26、输出NG Not Good 不行，不合格C=0 Critical=0 极严重不允许APP Approve 核准，认可，承认CHK Check 确认ASSY Assembly 装配，组装T/P True Position 真位度5WIH When, Where, Who, What, Why, Ho w to6M Man, Machine, Material, Method, Mea surement, Message4MTH Man, Material, Money, Method, Time, How人力，物力，财务，技术，时间（资源）SQA Strategy Quality Assuran

27、ce 策略品质 保证DQA Design Quality Assurance 设计品质 保证MQA Manufacture Quality Assurance 制 造品质保证SSQA Sales and service Quality Assuran ce销售及服务品质保证 LRR Lot Reject Rate 批退率DVD Digital Video Disk VCD Video Compact Disk LCD Liquid Crystal Display CAD Computer Aided Design CAM Computer Aided Manufacturing CAE Computer Aided Engineering PCB Printed Circuit Board ER刷电路板 CAR Correction Act