SPC-P175-36V 8Ah 规格书-H版-订单 YP-SD-C114 客供外壳

1、.：.；江西中投新能源JIANG XIZ.T NEW ENERGY CO.,LIMITED规格确认书Specification for ApprovalSeries产品系列Lithium PolymerModel and Capacity型号及容量36V 8AhCustomer Name or code客户称号或代码YP-SD-C114File No.文件编号ZT -SPC-P175File Version版本号A0Issue Date发行日期2021-08-04同意Approved审核Checkup制造PreparedCustomer Approval客户确认Signature签名Date日

2、期Company Name:公司称号：Company Stamp:公司印章：江西中投新能源JIANG XIZ.T NEW ENERGY CO.,LIMITEDAEMDMENT RECORDS(规格变卦记录)版本号 Version Number变卦内容描画Emendatory content description更改页 Emendatory page发行日期 Issued Date制造Prepared审核Checkup同意Approved制造商保管在没有预先通知的情况下改动和修正设计及规格阐明书的权益 1 of 10 Manufacturer reserve the right to alte

3、r or amend the design, model and specification without prior notice Contents目录1 适用范围Scope32 体系System 33 常规技术参数General Specifications34 产品性能测试Product performance test 45 产品储存及运输Product Storage and Transportation66 电池操作指引Battery Handling Guideline 67 本卷须知Remark8附录Appendix9制造商保管在没有预先通知的情况下改动和修正设计及规格阐明书

4、的权益 2 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice 1.适用范围Scope本产品规格书适用于江西中投新能源向客户提供的可充电锂聚合物电池产品 36V 8Ah。This specification is applied to rechargeable Lithium Polymer Cell 36V 8Ah produced by Jiangxi Z.T New Energy CO., LTD.2. 体系Syste

5、m可充电聚合物锂离子电池Rechargeable Lithium Ion Polymer Battery3. 常规技术参数General SpecificationsNO.工程Item规格参数Specification1型号 Model36V8Ah ( 2P10S)2额定容量 Rated Capacity ( 5A)最小值:Min.: 8Ah HYPERLINK mailto:2Acharge (2Acharge and 5A discharge)特征值:Typical:8.5Ah HYPERLINK mailto:2Acharge (2Acharge and 5A discharge)3内阻

6、 internal Impedance 200mohm4标称电压Nominal Voltage36V5充电截止电压Charging Voltage420.05V6充电方法Charging Method恒流恒压充电 CC&CV规范充电制度Standard Charging Process在 25C5 C 下，以 2A 恒流充电至 42V,然后恒压充电到充电电流减小到 0.02C，即充溢电。2A (CC) charge to 42V, when 42V (CV) is reached, charge rate will reduce to 0.02C(A) for full charge7放电方法

7、Discharging Method恒流放电 constant current discharge8规范放电制度Standard Discharge method在 20C5 C 下以 5A 恒流放电至 30.0V。Cells should be discharged at a constant current of 5Ato 30.0 volts at 20C 5 C9规范放电时间Standard discharge time120min10最大继续放电电流Max. Continuous DischargeCurrent8A11放电截止电压Discharge Cut-Off Voltage3

8、0.0V制造商保管在没有预先通知的情况下改动和修正设计及规格阐明书的权益 3 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice 12电池外壳资料The crust data客供外壳，最大外形尺寸为435mm 81mm130mm详细见附图The curst is supplied by the client，the maximum dimensions is435mm 81mm130mm， refer to the atta

9、ched drawing13电池分量(最大值)Battery Weight(MAX)3.5Kg14电池循环寿命 (规范充放电)battery Cycle Lifestandard charge& discharge 500 次 注:剩余容量60%remark: the residualcapacity is more than 60% of the first cycle discharge capacity15操作温度 Operating Temperature放电Discharge-20C to 55C充电Charge0C to 45C储存Storage10C to 30C16储存温度 S

10、torage temperature1 个月内Within 1 month- 5C +45C3 个月内Within 3 month- 5C +35C6 个月内Within 6 month0C +35C4. 产品性能测试Products performance testNO.ItemsTestcondition and methodCriterion1荷电性能Self-dischargePerformance规范充电后在 205条件下储存 30 天，然后用 5A 的电流放电至放电截止电压 Standard Charged according to 5. 3.1，lay for 30 days i

11、n the aminenttemperature of 20 C5 C,then discharge to the discharge end voltage 30.0 V at the current of 5A放电容量: 85%初始容量The discharge Capacity: should not less than 85% of Initial Capacity2高温放电性能High TemperatureDischarge规范充电后，把电池放入 555高温箱中搁置 2 小时，然后然后用 0.2C 的电流放电至放电截止电压standard Charged according to

12、5. 3.1，lay for 2 hoursin the ambient temperature of 55 C5 C, then discharge to the discharge end voltage 30.0V at the current of 0.2C放电容量 90%常温放电容量The Discharge capacity should not less than 90% of the capacity that discharge at normal temperature3低温放电性能Low TemperatureDischarge规范充电后，把电池放入-205低温箱搁置 1

13、6-24h 后用 0.2C 的电流放电至放电截止电压standard Charged according to 5. 3.1，lay for 24hours in the ambient temperature of -20 C5C ,then discharge to the discharge end voltage30.0V at the current of 0.2C放电容量 70%常温放电容量The Discharge capacity should not less than 70% of the capacity that discharge at normal temperat

14、ure制造商保管在没有预先通知的情况下改动和修正设计及规格阐明书的权益 4 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice 4过充电测试Over charge test规范充电后，恒流恒压源设定为 50V 以 1C 的电流继续充电 8hBattery charged at 1.0C current with a voltage limit of50.0V.charging is continued for 8 hours

15、.不爆炸、不起火no explosion, no fire5过放测试Over-discharge0.5C 放电至 30.0V 后再以 0.2C 的电流放电至 0VBattery discharged continuously at the constant current of 0.5C to 30.0V,then discharge the battery with a current of 0.2Cto 0V不爆炸、不起火No Explosion, No Fire6热冲击测试Heating Test将满电电池置于高温箱中、温度以52/min 升到 1302并保温 30 分钟The temp

16、erature of the oven is to be raised at a rate of 52/min. to a temperature of 1302, andremains for 30 minutes at this temperature.不爆炸、不起火No Explosion, No Fire7振动测试Vibration test电池在振幅为 0.8 mm 1.6mm的简谐振动，振动频率为：1055 Hz,扫频速率为:1 Hz/min, X、Y、Z 三个方向各振动一次，振动时间为 30min.Let the battery subjected simple harmonic

17、 motion with an amplitude of 0.8 mm 1.6mm total maximumexcursion.The frequency is to be varied at the rate of1 hertz per minute between 10 and 55 hertz, The battery is to be tested for 30 min in each mutually perpendicular directions.不爆炸、不起火No Explosion, No Fire8自在跌落测试 Free falling(drop) Test规范充电后，搁

18、置 2 小时,从 1m 高处自在跌落到 30mm厚的木板上,各方向一次。Fully charge，lay for 2 hours , drop the battery from aheight of 1m to a wooden board with the thickness of30mm. Each side for one time.不爆炸、不起火(V0.20V/SetR5%/Set)No Explosion, No Fire9外部短路测试ExternalShort-circuitingtest规范充电后，运用总内阻不大于 100m 的导 线 短路 正负极 ， 当 电池温度下 降 到 比

19、峰值 低 约 10 时， 终了 试 验 。Fully charge，Short circuit by connecting the positive and negative terminals with a circuit load having a maximum resistance load of 100m ,un t il i t st e m p e r a t u r e h a s f a ll e n b y 10 f r o m t he p ea k p o i n t , t h e t e s t i s o v e r .不爆炸, 不起火No explosion,

20、no fire10温度循环测试 Temperature Cycling Test703条件下搁置 4 小时；在 203条件下搁置 2 小时；在-403条件下搁置 4 小时；在 203条件下搁 置 2 小时；按以上的步骤循环 10 次，并且每次温度变 换时间不得超越 30min 。70 3C maintaining for 4 hours.203C maintaining for 2 hours.-40 3C maintaining this temperature for4 hours.203C for 2 hours. Repeating the sequence for a further

21、 9 cycles. And the temperature changeshould be finished within 30 min不着火、不爆炸；不漏 气、不漏液No Explosion, No Fire and Not vent or leak11恒 定 湿 热 测 试Humidityand heat test将规范充电后的电芯放入温度为402，相对湿度为90%95%的恒温恒湿箱中48hA charged battery is placed in a box for 48hours where the temperature is 40C2Cand the relative humi

22、dity is 90%95%无冒烟、爆炸 No smoke or explosion12重物冲击测试Impact test电池按 5.3.1 充电后，把电池放在一个平面上，将直径为 15.8mm 的钢棒放到电池的中心，用分量为 9.1kg 的不爆炸, 不起火No explosion, no fire制造商保管在没有预先通知的情况下改动和修正设计及规格阐明书的权益 5 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice 重物从

23、 610mm 的高度跌落到电池上.After full charged according tosection5.3.1,place the battery on a flat surface. A 15.8mm diameter bar is to be placed across the center of the sample. A 9.1 kgweight is to be dropped from a height of 61025 mm onto the sample.13挤压测试Crush Test在两个平面间对电池进展挤压，压力经过直径为 32mm的活塞提供，压强为 17.2

24、MPa，压力为 13 kN 即可停止。Crush the battery between two flat surfaces ,The force for the crushing is to be applied by a hydraulic ram with a 32 mm diameter piston. The crushing is to be continued until a pressure reading 17.2 MPa is reached on the hydraulic ram, applied force of 13 kN.不爆炸, 不起火No explosion,

25、 no fire5.产品储存及运输Product Storage and Transportation5.1 产品储存ProductStorage如电池储存 3 个月以上，电池须置于温度为 205、湿度为 6520%RH 的环境中，电池的储存电压需坚持在 36V40V，请每隔 3 个月电池一次，详细方法如下:规范充放电后，搁置 5 分钟，2A 充电至40VIf the cell is to be stored for 3 months or longer , the environment should be as follows: Temperature: 205Humidity: 6520

26、%RHVoltage during storage needs to me maintained between 36V40V .Please charge & discharge the battery once every 3 months according to the following method: Standard charge/discharge, lay for 5 min, then charge at 2A to 40V.5.2 产品运输Product Transportation电池在运输中为半电形状，应防止猛烈震动、挤压、日晒及浸湿。During transport

27、ationthe battery is approximately at a state of 50% charged, the battery should avoid from acute vibration, crushed, solarization, soaked.6.电池操作指示及本卷须知Handling Precautions and Guideline声明一： 客户假设需求将电池用于超出文件规定以外的设备，或在文件规定以外的运用条件下运用电池，应事先联络中投新能源，由于需求进展特定的实验测试以核实电池在该运用条件下的性能及平安性。Note(1):If the battery i

28、s used to other equipments , or used condition is not accord to the condition in this制造商保管在没有预先通知的情况下改动和修正设计及规格阐明书的权益 6 of 10 Manufacturer reserve the right to alter or amend the design, model and specification without prior notice Specification they should contact With Z.T New Energy in advance, Ad

29、ditional experimentation may be required to verify the performance and safety under the conditions.声明二：对于在超出文件规定以外的条件下运用电池而呵斥的任何不测事故中投新能源概不担任Note(2):Z.T New Energy will take no responsibility for any accident when the battery is used under other conditions beyond those described in this Document.声明三

30、：如有必要，中投新能源会以书面方式告之客户有关正确操作运用电池的改良措施。Z.T New Energy will inform the customer of improvements regarding proper use and handing of the battery in a written form, if it is necessary.6.1. 充电 Charging电池必需在 040的环境温度范围内进展充电，充电电流不得超越本规范书中规定的最大充电 电流。充电电压不得超越本规范书中规定的额定电压,42V 为充电电压最高极限，充电器的设计应满 足此条件；制止反向充电， 用我

31、公司配套的充电器或引荐的充电方法进展充电，充电时间不得超越7hThe battery should be charged within 040 specified in this Specification. The battery should be charged at a current less than the maximum charge current specified in this Specification. Charging Voltage should be less than the specified in this Specification. The Max

32、Charging Voltage is 42V, and the charger should be designed to meet with this requirement. Prohibiting toreverse charge，Charge the battery with the charger or charge method offer by our company, thecharge time not more than 7h6.2放电 Discharging电池必需在-2060的环境温度范围内进展放电，放电电流不得超越本规范书规定的最大放电电 流，留意在电池长期未运用期

33、间能够会因其它自放电特性而处于某种放电形状。为防止电池过放电， 应定期充电，坚持其电压高于 30V。The battery should be discharged within -2060 specified in this Specification, The batteryshould be discharged at a current less than the maximum discharge current specified in this Specification. Notice that the battery would be at force-discharged

34、state by its self-discharge characteristics in case the battery is not used for long time. In order to prevent over-discharging, the battery shall be charged periodically to maintain above 30V.6.3.其它事项 Others6.3.1.防止电池内短路Prevent internal short circuit6.3.2.严禁装配电池 Prohibit disassembly6.3.3. 在任何情况下，不得将电池投入火中，否那么会引起电池熄灭。Never dispose the battery in fire. It may cause the battery firing.6.3.4 不得将电池浸泡于液体中，如淡水、海水、饮料