普通胶合板测试报告.

1、检测报Test Report检测工程:普通胶合板Test ItemsPlywood for General Use委托单位:狮山冠锋木业制品Applicant Shishca Guanfeng Wood Products Co, Ltd.检测类别：委托检验Test TypeEntrusted Test收样日期：2018-10-22Received Date October 22nd,2018考前须知Precautions.检测报告无本单位检测专用章或骑缝章无效。Test report is invalid if not affixed with Authorized Stamp of Test

2、 or Paging Seal.检测报告无审核人、批准人签字无效。Test report is invalid without signature of verifier and approver.检测报告涂改增删无效。Test report is invalid only if being supplemented, deleted or altered.未经本单位书面许可不得局部复制检测报告(全部复制除外)。Without prior written permission of HJK, the test report cannot be reproduced, except in ful

3、l.除非另有说明，本报告检测结果仅对测试样品负责。Unless otherwise stated, the results shown in this test report are responsible for the delivered sample(s).对检测报告假设有异议，应于收到报告之日起十五天内向检测单位提出。Objections to the test report must be submitted to HJK within 15 days of report received date.样品信息由送样人提供，实验室不负责核实信息真实性。The test applican

4、t is responsible for authenticity of sample information which not subject to verification of HJK LAB.上海宏骏科技实验室具备由美国IAS认可的满足ISO/IEC 17025要求的资质。Shanghai Hongjun Science & Technology Co., Ltd. is an ISO/IEC 17025-conforming test laboratory, which is accredited by International Accreditation Service, In

5、c.样品描述/Sample Description收到的样品为普通胶合板，样品包装完整、状态完好。样品规格尺寸如下表所示。The samples received are Plywood for general use. All test samples are packed well and kept in good conditions. The dimension specifications of the samples are shown in below table.测试工程尺寸规格 长*宽*厚(mm)数量(片)含水率Moisture Content100*25*8.53胶合强度B

6、onding strength100*25*8.512浸渍剥禺Impregnation Delamination75*75*8.56抗弯强度Bending Strength220*50*8.512弹性模量Bending Modulus of Elasticity220*50*8.512甲醛释放量Formaldehyde Emission250*150*8.53.检测标准/Testing Standards根据客户要求，样品根据如下标准进行测试：According to applicanfs requirements, the samples are tested according to th

7、e following standard:GB/T 9846-2015普通胶合板GB/T 17657-2013人造板及饰面人造板理化性能试验ASTM D6007-2014 Standard Test Method for Determining Formaldehyde Concentrations in Air from Wood Products Using a Small-Scale Chamber.检测描述/Testing Description测试环境温度为232、相对湿度为605%。测试日期从2018年10月25日至11月6日 The temperature and relativ

8、e humidity of test environment are 232 and 60 + 5%, respectively. The tests were conducted from October 25th, 2018 through November 6th, 2018.检测结果/Test Results序号No.测试工程Test Items单位Units标准要求Standard Requirements测试结果Test Results判定结果Conclusion1含水率Moisture Content%51411.7通过 Pass2胶合强度Bonding strengthMPan

9、类 20.701.83通过 Pass3浸渍剥离Impregnation Delaminationmm每个试件同一 胶层每边剥离 长度累计不超 过 25mm。The cumulative peeling length of each specimen does not exceed that of 25mm in the same adhesive layer.15.0N/A4抗弯强度Bending StrengthMPa21224.2通过 Pass弹性模量 Bending Modulus of ElasticityMPa20002602通过 Pass5甲醛释放量1Formaldehyde Em

10、issionppmW0.050.04通过 Pass备注/Notes:.浸渍剥离强度测试工程限值要求适用于相邻单板纹理相互平行的样品。The limit value requirements of impregnation delamination are applicable to applicable to test samples whose wood grain of adjacent veneers are perpendicular to each other.甲醛释放量测试的指标要求参照加州空气资源局93120法规表格一及美国联邦法案40 CFR Part 770第 770.10中

11、要求的单板芯的硬木胶合板第二阶段0.05ppm的限值要求。Index requirements for formaldehyde emission measurement are referenced to CARB 93120, Tablet, Phase 2& 770.10 of 40 CFR Part 770 limitation of0.05ppm forHWPW-VC.:初Reported by： *Reviewed by：附录1 测试结果Appendix I - Test Data1.含水率/Moisture Content编号 No.长Length(mm)宽Width (mm)厚

12、Thickness (mm)气干质量 Weight Before Conditioning( mm)绝干质量 Weight After Conditioning( mm)含水率 Moisture Content1100.2325.128.5813.0911.7211.7%2100.4525.318.4912.9711.6411.4%3100.3825.418.5413.4812.0412.0%2.胶合强度/Bonding strength编号 No.长度Length (mm)宽度 Width (mm)厚度Thickness (mm)极限载荷Ultimate Load(N)胶合强度Bonding

13、 strength (MPa)木破率wood failure percentage124.9025.538.991195.21.88100%224.4925.399.011465.82.36100%324.6025.468.961897.63.03100%424.1325.539.152485.44.03100%524.5025.479.011729.22.77100%623.9125.519.011662.02.72100%723.8525.419.031197.21.98100%824.4725.439.071650.82.65100%923.8725.599.081228.82.0110

14、0%1023.8025.429.142760.24.56100%1124.0825.579.012825.04.59100%1223.9425.559.053263.05.33100%3.浸渍剥离/Impregnation Delamination编号No.长度Length (mm)宽度Width (mm)厚度Thickness (mm)单边剥离总长的最大值 Maximum Value ofSingle Delamination Bond Line (mm)175.3575.338.460.0275.2775.298.510.0375.2575.358.490.0475.3275.288.52

15、0.0575.1575.278.4915.0675.1775.298.480.04,抗弯性能/Bending Properties抗弯强度/Bending Strength编号No.宽Mid-Span Width (mm)厚Mid-Span Thickness (mm)极限载荷Ultimate Load (N)抗弯强度Bending Strength(MPa)150.168.59313.221.6250.068.49357.425.3350.178.55288.020.0450.128.55385.426.8550.168.57352.424.4650.178.52345.224.2750.0

16、48.54336.223.5849.998.55360.425.1950.168.55342.823.81050.098.61359.824.71150.138.57399.827.71250.168.59340.023.4弹性模量/Bending Modulus of Elasticity编号 No.宽 Mid-Span Width (mm)厚Mid-Span Thickness (mm)弹性段斜率Slope of Elastic Segment (N/mm)弹性模量Modulus of Elasticity (MPa)150.168.5955.662150250.068.4971.0728

17、49350.178.5563.522488450.128.5562.452448550.168.5762.472430650.178.5266.192620750.048.5471.542819849.998.5567.632658950.168.5567.2226331050.098.6170.5827121150.138.5770.5127451250.168.5969.142671附录2样品照片Appendix II - Sample Photosp ( fS 1I?fe豆5 (7SI o； 挛6I J06 08 7Z 09_OOPOS湍oQoe:加d6 Os06 018 OZO9 .产 csBh|UK|llll|UH|lll!llll!lhUHir OK ol 03 oik,08 yL 09”OGUOS仰?脑。件平坪品“J” M叫加加加加曲11岫曲!而inOS00k09,i 0忆0&乙0I C6,Qe 0jZ.0ft 即邮而n加加和而加喻加小而曲向ilw伽加Mu r