AlomSun服务器管理详解上课讲义

1、Good is good, but better carries it.精益求精，善益求善。AlomSun服务器管理详解-发信人:hutu(难得糊涂霜林孤雁),信区:UNIX标题:SunALOM使用指南发信站:烟雨漓江BBS站(SatJan1322:30:162007),站内SunALOM使用指南/bypupil2006.12.20SunAdvancedLightsOutManager简称ALOM,是一种系统控制器,可以通过它远程管理和控制Sun服务器.ALOM运行的载体是SC卡,有时也称SC卡为ALOM系统控制器.注意:SUNW,Sun-Fire-T2000上的ALOM与这里的ALOM不一样

2、,不要混淆.SC卡是SUNW240,SUNW440系列内置的组件,在SUNW,Sun-Fire-V240;SUNW,Netra-240中集成在主板上,在SUNW,Sun-Fire-V440;SUNW,Netra-440内SC卡做成一块板卡插在PCI插槽内.注意:SUNW,Sun-Fire-T2000上的SC卡与这里的SC卡不一样,不要混淆.目前SC卡的固件版本是1.6,SC卡的Bootmon和Firmware固件的最新版本为1.6.2(2006年12月份)ALOM的运行不依赖于SunOS,也不依赖于OBP固件.一旦接通电源,ALOM就开始运行,而不管POST,SunOS是否运行.可以在SunO

3、SShell下用scadm来设置ALOM,例如bash#/usr/platform/uname-i/sbin/scadmversion或者bash#/usr/platform/$(uname-i)/sbin/scadmversionSCVersionv1.6SCBootmonVersion:v1.6.2SCFirmwareVersion:v1.6.2其中注意上面的是键盘Esc下面的那个键,而不是单引号,uname-i的结果是当前机器的平台直接支持scadm的系统有SUNW,Netra-440;SUNW,Sun-Fire-V440;SUNW,Netra-240;SUNW,Sun-Fire-V24

4、0;SUNW,Sun-Fire-T2000的ALOM不支持scadm操纵ALOM,要恢复该ALOM密码可以在ALOM舳时候按Esc键中断SC卡的引导,然后恢复ALOM的缺省配置.不支持scadm操纵ALOM的系统有SUNW,Sun-Fire-V890,SUNW,Sun-Fire-V880,SUNW,Sun-Fire-V490,SUNW,Sun-Fire-V480,SUNW,Sun-Fire-280R,这些系统用的不是ALOM而是SunRemoteSystemControl(RSC),需要安装SUNWrsc,然后才可以使用实用工具rscadm来设置RSC参数观察支持scadm的系统中scadm的

5、位置为/usr/platform/SUNW,Sun-Fire-V240/sbin/scadm其它位置都是符号连接到此文件bash#file-h/usr/platform/SUNW,Netra-440/usr/platform/SUNW,Netra-440:symboliclinktoSUNW,Sun-Fire-V440bash#file-h/usr/platform/SUNW,Netra-440/sbin/usr/platform/SUNW,Netra-440/sbin:symboliclinkto./SUNW,Sun-Fire-V240/sbinbash#file-h/usr/platfor

6、m/SUNW,Sun-Fire-V440/sbin/usr/platform/SUNW,Sun-Fire-V440/sbin:symboliclinkto./SUNW,Sun-Fire-V240/sbinbash#file-h/usr/platform/SUNW,Netra-240/usr/platform/SUNW,Netra-240/:symboliclinktoSUNW,Sun-Fire-V240bash#file-h/usr/platform/SUNW,Sun-Fire-V240/sbin/scadm/usr/platform/SUNW,Sun-Fire-V240/sbin/scadm

7、:ELF32-bitMSBexecutableSPARCVersion1,dynamicallylinked,strippedbash#ldd/usr/platform/SUNW,Sun-Fire-V240/sbin/scadmlibrsc.so.1=/usr/platform/SUNW,Sun-Fire-V240/lib/librsc.so.1libcurses.so.1=/usr/lib/libcurses.so.1librt.so.1=/usr/lib/librt.so.1libpthread.so.1=/usr/lib/libpthread.so.1libc.so.1=/usr/lib

8、/libc.so.1libaio.so.1=/usr/lib/libaio.so.1libmd5.so.1=/usr/lib/libmd5.so.1libdl.so.1=/usr/lib/libdl.so.1libthread.so.1=/usr/lib/libthread.so.1/usr/platform/SUNW,Sun-Fire-V240/lib/libc_psr.so.1/usr/platform/SUNW,Sun-Fire-V240/lib/libmd5_psr.so.1进一步观察ALOM虚拟的硬件设备为/dev/lom:bash#ls-ail/dev/lom1560lrwxrwx

9、rwx1rootroot31Dec2917:21/dev/lom-./devices/pseudo/tsalarm0:lombash#ls-ail/devices/pseudo/tsalarm0:lom1533crw-1rootsys214,0Dec2917:21/devices/pseudo/tsalarm0:lombash#grep214/etc/name_to_majortsalarm214bash#ls-ail/platform/uname-i/kernel/drv/tsalarm.conf1232-rw-r-r-1rootsys225Jun42004/platform/SUNW,Su

10、n-Fire-V240/kernel/drv/tsalarm.conf说明:/platform/uname-i/kernel目录存放与平台相关的核心模块查看与ALOM有关的驱动:bash#modinfo-i28IdLoadaddrSizeInfoRevModuleName28124710e36472031rmc_comm(rmc_commdriver,v1.4)bash#modinfo-c-i28IdLoadcntModuleNameState281rmc_commLOADED/INSTALLEDbash#modinfo-i35IdLoadaddrSizeInfoRevModuleName35

11、120bd07655e2041rmclomv(rmclomvcontroldriverv1.13)bash#modinfo-c-i35IdLoadcntModuleNameState351rmclomvLOADED/INSTALLED/rmclomv驱动在/var/adm/messages中记录与ALOM有关的SC事件,可以用dmesg/查看,注意是kern事件bash#modinfo-i131IdLoadaddrSizeInfoRevModuleName1317807ab96c8b2051rmcadm(rmcadmcontroldriverv1.2)bash#modinfo-c-i131Id

12、LoadcntModuleNameState1311rmcadmLOADED/INSTALLED/rmcadm驱动在OS启动后第一次运行实用工具scadm时加载,这时候dmesg会/出现如下记录/bash#dmesg|greprmcadm/Dec1810:29:04FireV240pseudo:ID129642pseudo-device:/rmcadm0/Dec1810:29:04FireV240genunix:ID936769rmcadm0is/pseudo/rmcadm0*/三个驱动的配置文件均在目录/platform/sun4u/kernel/drv下:bash#ls-ail/platf

13、orm/sun4u/kernel/drv/rmc*1219-rw-r-r-1rootsys1034Nov1320:11/platform/sun4u/kernel/drv/rmc_comm.conf1220-rw-r-r-1rootsys186Nov1320:11/platform/sun4u/kernel/drv/rmcadm.conf1237-rw-r-r-1rootsys188Nov1320:12/platform/sun4u/kernel/drv/rmclomv.conf在ALOMShell(即sc提示符)下按console或者console-f可以转到console口,在consol

14、e口(OBPShell(即OK提示符)或者SunOSShell下)按#.(默认值,用showsc可以看参数sc_escapechars)可以转换到ALOMShell下.注意此时在OSShell下使用eeprom或者在Ok下使用printenv时,output-device和input-device要显示为ttya,而不能是output-device=screen,input-device=keyboard,除非没有机器没有显卡和未插入键盘,否则将无法正常使用串口.要在ALOMShell下把console设置为ttya的话可以使用bootmodereset_nvram的办法,例如在SunFire

15、V240/V440上可以如下的办法(SunFireT2000在T2000ALOMShell下,SunFireV120上在LOMShell下,SunFire280R/490/890在RSCShell下也都同样操作):scbootmodereset_nvramscbootmodeBootmode:reset_nvramExpiresMONDEC1802:49:13UTC2006scresetResetcommandisdisabledwhensystemispoweredoff.scpoweron这样的话console被设置为ttya.某些类型的机器(比如SunFire280R/V490/V890

16、等)把NVRAM的配置重置成初始化状态可以用Sun键盘的STOP+N功能,或者使用下面的办法模拟:在机器待机状态下,按On/Standby按钮后,在故障LED快闪阶段,迅速按On/Standby按钮两次(在一秒之内),这样将NVRAM的配置重置成初始化状态.如果是RSC卡的话,则output-device和input-device要显示为rsc-console,Enterprise250的话为rsc,在装有RSC卡的机器的OBPShell下可以设置diag-console为rsc,Enterprise250的话设置diag-output-to为rsc而不是diag-console为rsc;如果

17、是Fire-T2000的ALOM的话,则output-device和input-device要显示为virtual-console;ok.versionRelease4.16.6created2005/05/0913:03OBP4.16.62005/05/0913:03SunFireV210/V240,Netra240OBDIAG4.16.62005/05/0913:05POST4.16.52005/02/2816:33ok.scSEEPROM:OKI2C:OKEthernet:OKEthernet(2):OKCPU:OKRAM:OKConsole:OKSCControlline:OKFlas

18、hRAMBootCRC:OKFlashRAMMainCRC:OKok.asrTherearenodevicesdisabledbyASR.okprintenv.output-devicettyattyainput-devicettyattya.bash#/usr/platform/SUNW,Sun-Fire-V240/sbin/eeprom.output-device=ttyainput-device=ttya.下面是机器刚接通电源时候串口显示的内容:ALOMBOOTMONv1.5.4ALOMBuildRelease:008Resetregister:e0000000EHRSESRSLLRS/

19、*如果是重置SC卡的话,上一行改为/*Resetregister:e8000000EHRSESRSLLRSCSRS/*以后还有一处不一样,整个过程共有两个地方不一样ALOMPOST1.0DualPortMemoryTest,PASSED.TTYExternal-InternalLoopbackTest/*如果是重置SC卡的话,上一行改为/*TTYExternal-InternalLoopback/*以后的部分全都一样TTYExternal-InternalLoopbackTest,PASSED.TTYC-InternalLoopbackTestTTYC-InternalLoopbackTest

20、,PASSED.TTYD-InternalLoopbackTestTTYD-InternalLoopbackTest,PASSED.MemoryDataLinesTestMemoryDataLinesTest,PASSED.MemoryAddressLinesTestSlideaddressbitstotestopenaddresslinesTestforshortedaddresslinesMemoryAddressLinesTest,PASSED.MemoryParityTestMemoryParityTest,PASSED.BootSectorFLASHCRCTestBootSector

21、FLASHCRCTest,PASSED.ReturntoBootMonitorforHandshakeALOMPOST1.0Status=00007fffReturnedfromBootMonitorandHandshakeClearingMemoryCellsMemoryCleanCompleteLoadingtheruntimeimage.Sun(tm)AdvancedLightsOutManager1.5.4(Fire-V240)FullVxDiagTestsBASICTODTESTReadtheTODClock:THUMAR0211:17:232006Wait,1-3secondsRe

22、adtheTODClock:THUMAR0211:17:252006BASICTODTEST,PASSEDETHERNETCPULOOPBACKTEST50BYTEPACKET-a0infieldof1s.50BYTEPACKET-a1infieldof0s.900BYTEPACKET-pseudo-randomdata.ETHERNETCPULOOPBACKTEST,PASSEDFullVxDiagTests-PASSEDStatussummary-Status=7FFFVxDiag-PASSEDPOST-PASSEDLOOPBACK-PASSEDI2C-PASSEDEPROM-PASSED

23、FRUPROM-PASSEDETHERNET-PASSEDMAINCRC-PASSEDBOOTCRC-PASSEDTTYD-PASSEDTTYC-PASSEDMEMORY-PASSEDMPC850-PASSEDPleaselogin:/usr/platform/SUNW,Sun-Fire-V240/sbin/scadmuserpasswordadmin用来设置用户admin的密码,为将来登录ALOM作准备/usr/platform/SUNW,Sun-Fire-V240/sbin/scadmsetnetsc_ipaddr设置ALOM网卡IP地址,还可以设置掩码,网关/usr/platform/S

24、UNW,Sun-Fire-V240/sbin/scadmresetrsc重置ALOM.使IP设置生效然后telnetCopyright2004SunMicrosystems,Inc.Allrightsreserved.Useissubjecttolicenseterms.Sun(tm)AdvancedLightsOutManager1.5.4(Fire-V240)Pleaselogin:adminPleaseEnterpassword:*scsetscif_emailalertstrue/*使E-mail报警生效*/scsetscmgt_mailhost7/*设置SMTP邮件服务器地址*/sc

25、setscsys_eventlevel3/*设置报警级别*/scsetscmgt_mailalertpupil3/*设置报警信箱和级别*/scresetsc-y/*重置ALOM,使之生效,这时候LED指示灯将会熄灭,并且ALOM重启后不会自动点亮指示灯,440系列的话重置ALOM后指示灯仍然亮着*/过一会再telnet上Copyright2004SunMicrosystems,Inc.Allrightsreserved.Useissubjecttolicenseterms.Sun(tm)AdvancedLightsOutManager1.5.4(Fire-V240)Pleaselogin:ad

26、minPleaseEnterpassword:*sc在sc下面输入break-y可以使操作系统中断进入OBPShell,然后在OBPShell下输入go可以又恢复到OSShell下说明一:RSC卡也可以在RSCShell下通过输入break使操作系统中断进入OBPShell,然后在OBPShell下输入go可以又恢复到OSShell下.说明二:Fire-V440,Netra-440,Fire-V490默认不支持break中断操作系统进入OBPShell,Fire-V240,Netra-240,Fire-280R,Fire-V890默认支持break中断操作系统进入OBPShell.如果需要将不

27、支持break中断操作系统进入OBPShell,这时候需要在OSShell下用kbd-aenable可以立即生效或者修改/etc/default/kbd重启后生效bash#grep-v#/etc/default/kbdKEYBOARD_ABORT=alternatebash#grepKEYBOARD_ABORT/etc/default/kbd#KEYBOARD_ABORTaffectsthedefaultbehaviorofthekeyboardabort#KEYBOARD_ABORT=disableKEYBOARD_ABORT=alternate将上面的KEYBOARD_ABORT=alte

28、rnate注释掉或者改成KEYBOARD_ABORT=enable拔掉键盘、键盘发出中断又或者通过SC卡发出break都会使设备侦测到一次BREAK事件.BREAK事件将中断操作系统,使系统进入OBP(openbootprom)监视状态.如果启动内核时使用了kadb内核调试器,BREAK条件使系统进入kadb调试状态,可以通过mankbd了解相关情况:kbdenable|disable|alternateenable:允许STOP-Adisable:禁止STOP-Aalternate:允许拔掉键盘,但不禁止STOP-AscshowscAdvancedLightsOutManagerv1.5.4

29、parametervalue-if_networktrueif_modemfalseif_emailalertstruesys_autorestartxir/ALOM用软件狗进程来监控内核,如果内核(非普通进程)挂起,且软件狗超时,/则ALOM会报告/并记录相关事件,然后执行三种可能操作:/xir:默认操作,使服务器同步文件系统,然后重新启动操作系统.如果同步文件系/统时挂起,则/ALOM将在15分钟退出并硬重置系统;/reset:不同步文件系统,直接硬重置系统,这样有可能造成文件系统的损坏/none:软件狗超时后不做任何动作,这样系统将保持挂起状态/ALOM的软件狗查询间隔以及超时参数用户无

30、法自己设置sys_bootrestartnonesys_bootfailrecoverynonesys_maxbootfail3sys_xirtimeout0sys_boottimeout120sys_wdttimeout60netsc_tpelinktesttruenetsc_dhcpfalsenetsc_ipaddrnetsc_ipnetmasknetsc_ipgateway54mgt_mailhost7mgt_mailalert(1)pupil3sc_customerinfoSunFire-V240sc_escapechars#.sc_powerondelayfalsesc_powers

31、tatememoryfalsesc_clipasswdechotruesc_clipromptscsc_clitimeout0sc_clieventlevel2sc_backupuserdatatruesys_eventlevel3ser_baudrate9600ser_paritynoneser_stopbits1ser_data8netsc_enetaddr00:03:ba:50:3a:12sys_hostnameFire-V240sys_enetaddr00:03:ba:50:3a:09scshowscversion-vAdvancedLightsOutManagerv1.5.4SCFi

32、rmwareversion:1.5.4SCBootmonversion:1.5.4SCBootmonBuildRelease:08SCbootmonchecksum:F08ACA76SCBootmonbuiltOct172005,13:23:12SCBuildRelease:08SCfirmwarechecksum:2E078305SCfirmwarebuiltOct172005,13:22:53SCfirmwareflashupdateFEB272006,01:00:22SCSystemMemorySize:8MBSCNVRAMVersion=bSChardwaretype:0同时在本机7的

33、tcp25断口监听C:WINNTsystem32nc-vvnlp25listeningonany25.connectto7from(UNKNOWN)1024220HELOFire-V240220MAILFROM:alom-alertFire-V240220RCPTTO:pupil220DATA220From:alom-alertFire-V240To:pupilSubject:SystemAlertFromFire-V240SystemEventRecordedBySC:HostID:83503a09Event:00060003Time:SATDEC3103:41:092005Customer

34、Info:SunFire-V240Hostname:Fire-V240SCIPAddress:Message:CRITICAL:SCSystembooted.220QUITsent24,rcvd448可以看到ALOM发来的报警信息要注意的是220是需要手动输入的用nmap扫描了一下ALOMOS发现除了23tcp端口,还开了42tcp端口ALOM系统在TCP42端口监听,连接过去显示一个用数字8组合而成的字母G的ASCII图案C:WINNTsystem32nc-vvn42(UNKNOWN)42(?)open.,ad88888888baa,d8888888888888888888ba.a88888

35、888888888888888888888aa888888888888888888888888a,888888888PV8888888888,88888888PV888888888,888888888888888888888888888888888,8888888888888888._._._._._._._._._88888888,8888888888888888(88888888,V8888888888888888888888,Y888888888888888888888ba,.d888888888888V888888888888uouououo8888888888888888888888

36、888888888888888888888P88888V88888888888888888888888PV88888888888888888888PV8sent0,rcvd1082:NOTSOCKNMAP扫描结果:C:WINNTsystem32nmap-vvn-sT-p1-65535Startingnmap3.50(/nmap)at2006-01-0310:39中国标准时间Hostappearstobeup.good.InitiatingConnect()Scanagainstat10:39Addingopenport42/tcpAddingopenport23/tcpTheConnect()

37、Scantook16410secondstoscan65535ports.Interestingportson:(The65533portsscannedbutnotshownbelowareinstate:filtered)PORTSTATESERVICE23/tcpopentelnet42/tcpopennameserverNmapruncompleted-1IPaddress(1hostup)scannedin16414.918secondsC:WINNTsystem32nmap-vvn-sU-p1-65535Startingnmap3.50(/nmap)at2006-01-0315:1

38、4中国标准时间Hostappearstobeup.good.InitiatingUDPScanagainstat15:14TheUDPScantook105secondstoscan65535ports.All65535scannedportsonare:closedNmapruncompleted-1IPaddress(1hostup)scannedin109.765secondsC:WINNTsystem32nmap-vvn-OStartingnmap3.50(/nmap)at2006-01-0317:13中国标准时间Hostappearstobeup.good.InitiatingSYN

39、StealthScanagainstat17:13Addingopenport23/tcpAddingopenport42/tcpTheSYNStealthScantook4secondstoscan1659ports.ForOSScanassumingthatport23isopenandport1isclosedandneitherarefirewalledInterestingportson:(The1657portsscannedbutnotshownbelowareinstate:closed)PORTSTATESERVICE23/tcpopentelnet42/tcpopennam

40、eserverDevicetype:PBX|generalpurposeRunning:3Comembedded,TandemTandemNSKOSdetails:3ComNBXPBX,TandemNSKD40OSFingerprint:TSeq(Class=64K%IPID=I%TS=2HZ)T1(Resp=Y%DF=N%W=2000%ACK=S+%Flags=AS%Ops=MNWNNT)T2(Resp=N)T3(Resp=Y%DF=N%W=2000%ACK=O%Flags=A%Ops=NNT)T4(Resp=Y%DF=N%W=2000%ACK=O%Flags=R%Ops=)T5(Resp=

41、Y%DF=N%W=0%ACK=S+%Flags=AR%Ops=)T6(Resp=Y%DF=N%W=0%ACK=O%Flags=R%Ops=)T7(Resp=Y%DF=N%W=0%ACK=S%Flags=AR%Ops=)PU(Resp=Y%DF=N%TOS=0%IPLEN=38%RIPTL=148%RIPCK=0%UCK=0%ULEN=134%DAT=E)Uptime0.014days(sinceTueJan0316:53:262006)TCPSequencePrediction:Class=64KruleDifficulty=1(Trivialjoke)TCPISNSeq.Numbers:8E

42、4CC9BD8E4FB7BD8E50B1BD8E51ABBD8E52A5BD8E5593BDIPIDSequenceGeneration:IncrementalNmapruncompleted-1IPaddress(1hostup)scannedin10.765seconds下面给出SunFire-V440上ALOM的升级过程:bash#scadmdownloadbootalombootfwCopyingselftoRAM.Done.JumpingtoRAM.Waitingforbootprotocolmessage.GotOBP:bootinitmsg,dat2=00000001AMDfla

43、shROMReceivingsegment00000000GotS7/S8/S9recordwait_timewait_countwait_avgproc_timeproc_countproc_avg0160156e0000080100002bfd0017954f00000801000002f2idle_timeidle_countidle_avgtemp_timetemp_counttemp_avg00197793000008010000032e001002020000080000000200SendingTamale:bootokVerifyingbufferedimage.Downloa

44、dVerified-ProgrammingFlash.Segment00000000erasedandprogrammedFlashProgrammingComplete.Resetting.ALOMPOST1.0DualPortMemoryTest,PASSED.TTYExternal-InternalLoopbackTestTTYExternal-InternalLoopbackTest,PASSED.TTYC-InternalLoopbackTestTTYC-InternalLoopbackTest,PASSED.TTYD-InternalLoopbackTestTTYD-Interna

45、lLoopbackTest,PASSED.MemoryDataLinesTestMemoryDataLinesTest,PASSED.MemoryAddressLinesTestSlideaddressbitstotestopenaddresslinesTestforshortedaddresslinesMemoryAddressLinesTest,PASSED.MemoryParityTestMemoryParityTest,PASSED.BootSectorFLASHCRCTestBootSectorFLASHCRCTest,PASSED.ReturntoBootMonitorforHan

46、dshakeALOMPOST1.0Status=00007fffReturnedfromBootMonitorandHandshakeClearingMemoryCellsMemoryCleanCompleteLoadingtheruntimeimage.SCAlert:Failedtosendemailalertforrecentevent.SCAlert:SCSystembooted.SCAlert:Failedtosendemailalertforrecentevent.SCStatus7fff-OKEnter#.toreturntoALOM.Mar714:59:42Fire-V440r

47、mclomv:SCunretrievedmsgMAR0706:59:392006UTCSCSystembooted.bash#pwd/usr/platform/SUNW,Sun-Fire-V440/lib/imagesbash#scadmversionSCVersionv1.5SCBootmonVersion:v1.5.4SCFirmwareVersion:v1.5.2bash#scadmdownloadalommainfwCopyingselftoRAM.Done.JumpingtoRAM.Waitingforbootprotocolmessage.GotOBP:bootinitmsg,da

48、t2=00000002AMDflashROMReceivingsegment00000001Receivingsegment00000002Receivingsegment00000003Receivingsegment00000004Receivingsegment00000005Receivingsegment00000006Receivingsegment00000007Receivingsegment00000008Receivingsegment00000009Receivingsegment0000000aReceivingsegment0000000bReceivingsegme

49、nt0000000cReceivingsegment0000000dReceivingsegment0000000eReceivingsegment0000000fReceivingsegment00000010Receivingsegment00000011Receivingsegment00000012Receivingsegment00000013Receivingsegment00000014Receivingsegment00000015Receivingsegment00000016Receivingsegment00000017Receivingsegment00000018Re

50、ceivingsegment00000019Receivingsegment0000001aReceivingsegment0000001bReceivingsegment0000001cReceivingsegment0000001dReceivingsegment0000001eReceivingsegment0000001fGotS7/S8/S9recordwait_timewait_countwait_avgproc_timeproc_countproc_avg2a9831840000f80100002bf702dac1010000f801000002f2idle_timeidle_c

51、ountidle_avgtemp_timetemp_counttemp_avg0310b9990000f8010000032a01f1e81b0000f80000000201SendingTamale:bootokVerifyingbufferedimage.DownloadVerified-ProgrammingFlash.Segment00000001erasedandprogrammedSegment00000002erasedandprogrammedSegment00000003erasedandprogrammedSegment00000004erasedandprogrammed

52、Segment00000005erasedandprogrammedSegment00000006erasedandprogrammedSegment00000007erasedandprogrammedSegment00000008erasedandprogrammedSegment00000009erasedandprogrammedSegment0000000aerasedandprogrammedSegment0000000berasedandprogrammedSegment0000000cerasedandprogrammedSegment0000000derasedandprog

53、rammedSegment0000000eerasedandprogrammedSegment0000000ferasedandprogrammedSegment00000010erasedandprogrammedSegment00000011erasedandprogrammedSegment00000012erasedandprogrammedSegment00000013erasedandprogrammedSegment00000014erasedandprogrammedSegment00000015erasedandprogrammedSegment00000016eraseda

54、ndprogrammedSegment00000017erasedandprogrammedSegment00000018erasedandprogrammedSegment00000019erasedandprogrammedSegment0000001aerasedandprogrammedSegment0000001berasedandprogrammedSegment0000001cerasedandprogrammedSegment0000001derasedandprogrammedSegment0000001eerasedandprogrammedSegment0000001fe

55、rasedandprogrammedFlashProgrammingComplete.Resetting.ALOMPOST1.0DualPortMemoryTest,PASSED.TTYExternal-InternalLoopbackTestTTYExternal-InternalLoopbackTest,PASSED.TTYC-InternalLoopbackTestTTYC-InternalLoopbackTest,PASSED.TTYD-InternalLoopbackTestTTYD-InternalLoopbackTest,PASSED.MemoryDataLinesTestMemoryDataLinesTest,PASSED.MemoryAddressLinesTestSlideaddressbitstotestopenaddresslinesTestforshortedaddresslinesMemoryAddressLinesTest,PASSED.MemoryParityTestMemoryParityTest,PASSED.BootSectorFLASHCRCTestBootSectorFLASHCRCTest,PASSED.ReturntoBootMonitorforHandsh