Basics建模要件

1、BASICS建模要件STREAMS汽2 Passive Types (Type 0 and Type 6)- 2 被动型 (类型 0 和类型 6)水流动* Pressure Drop*压降HEAT EXCHANGERS热交换器GENERAL HEAT EXCHANGER WITH SPECIFIED SHELL AND TUBE INLET STREAMS带有特定壳侧和管侧进口汽水流动的通用热交换器REHEATER再热器GENERAL HEAT EXCHANGER WITH SPECIFIED HEAT SOURCE OR SINK带有特定放热源和吸热源的通用热交换器Stream Type 4

2、 Inlet类型4汽水流动的进口3. Nuclear Reheater (Type 22) “S” Port核电再热器（类型22）“S” 端口INPUT输入Input Data输入数据1. Generic Input (optional unless otherwise noted)通用输入（除非另行说明，均可选）- Cycle Flags (required, but input is default)- 循环标识（必选，输入是默认的）- Output Tables- 输出表格- Screen Display Variables- 屏幕显示的变量- Calculation Flags- 计算

3、标识- User Specified Material Properties- 用户指定的物质属性- 2nd Law Reference Data- 热力学第二定律参考数据- End Notes结束说明Input ProcessoSets and Cases设置和事例r*输入处理器*2. Run 2 cases using the data from Sets 1 and 2 for the first case, and Sets 1-4 for the second case.运行两个案例：第一个案例使用设置1和2中的数据，第二个案例使用设置1-4中的数据SCHEDULED VARIABL

4、E VALUES CALCULATED (All Special Features Calculated)计算预定变量值（计算所有特殊功能）FLAG SETTINGS AND DATA FOR SYSTEM系统标识旗的设置和数据· Short Cuts!· 快捷方式!· Operational Variables· 运算Operations (Equations)· 操作（方程）· 变量Input/Output Processor· 输入/输出处理器· Input/Output Values Must be Dep

5、endent输入/输出值必须是有函数关系的Operational Variables操作变量specifies 输入IWWMass flow (lbm/hr, kg/sec)IWW 质量流量(lbm/hr, kg/sec)IHCHeat Transfer Coefficient IHC传热系数IBSpressure drop equation B coefficient IBS压降方程式B系数（参见帮助）- Uses Special Output Processor to Export Data and Results- 使用特殊输出处理器输出数据和结果。specifies 规定Conserv

6、ation of Mass质量守恒All Inlet Ports Must be Resolved所有进口端口必须均已确定。· Turbine, Types 17· 汽轮机Heat Exchangers, Types 20-23, 28-29· 热交换器，类型20-23, 28-29- ，类型1-7Flag Design Mode in Input (or Choose Design Mode Component Type)输入中使用标识设计模式（Flag Design Mode）或选择设计模式部件类型（Design Mode Component Type）。Tu

7、be out Shell exit port superheat管道出口（壳侧出口以标准为基础的预测Ref-BasedPredictiveUse of Overall Heat Transfer Coefficients总体换热系数的使用· Components in Design Mode设计模式中的部件Condenser Sensitivity Study凝汽器灵敏度以标准为基础的预测Boiler Operating Parameter Study锅炉运行参数分析STREAMS汽水流动Fluid Passes Through Unchanged* 流体流动时状态恒定* Press

8、ure Drop*压降* Heat Loss*热损失GENERAL HEAT EXCHANGER WITH SPECIFIED HEAT SOURCE OR SINK带有特定放热源和吸热源的通用热交换器· Mixers (Type 50s) on the Main Steam Line, the Main Condensate/Feedwater Line, and Extraction Lines Must Route Main Flow Through “IA” and “U” Ports· 主蒸汽管路、主凝结水/给水和抽气管路上的混合加热器(类型50s)必须通过端口“

9、IA” 和 “U” 与总汽水流动相连接。IBHEnergy flux or Energy flow rate (Btu/hr, W)IBH能通量或能流速率(Btu/hr, W)ILBMass (lbm, kg) ILB质量(lbm, kg)IPPPressure (psia, kPa) IPP压力 (psia, kPa)IVVSpecific Volume (ft3/lbm, m3/kg) IVV比容(ft3/lbm, m3/kg)ILKSteam Rate 耗汽率 IUAThermal Conductance IUA换热率ITCThermal Conductivity换热性 ITRThermal Resistance 热电阻IFHVolume Flow Rate体积流量GENERAL HEAT EXCHANGER WITH SPECIFIED SHELL AND TUBE INLET STREAMS带有特定壳侧和管侧进口汽水流动的通用热交换器 Lines 行，线路，线Component N