项目实验报告-交换和热备一拓扑图和IP规划

1、项目实验报告-交换和热备一拓扑图和IP规划二各设备配置命令路由器配置命令ENCONF THOSTNAME BJ-R-1IP ROUTINGINT E0/1IP ADD 192.168.10.1 255.255.255.252NO SHUT EXITINT E0/2IP ADD 192.168.20.1 255.255.255.252NO SHUTEXIT第一台三层交换机的配置命令设置接口IP(IOS需用unzip-c3640-js-mz.124-10,IOS c3640-is-mz.123-13a不支持三层功能)ENCONF THOSTNAME BJ-RS-1IP ROUTINGINT F0/

2、15NO SWITCHPORTIP ADD 192.168.10.2 255.255.255.252NO SHUTEXITEXIT设置VTP和添加VLANVLAN DATABASEVTP DOMAIN YHLVTP SERVERVTP PASSWORD 321VTP PRUNINGVTP V2VLAN 2 NAME SALESVLAN 3 NAME ENGINEXIT为VLAN配置IPCONF TINT VLAN 1IP ADD 172.16.10.11 255.255.255.0NO SHUTEXITINT VLAN 2IP ADD 172.16.20.11 255.255.255.0NO

3、SHUTEXITINT VLAN 3IP ADD 172.16.30.11 255.255.255.0NO SHUTEXIT配置中继接口INT F0/1SWITCHPORT MODE TRUNKNO SHUTINT F0/2SWITCHPORT MODE TRUNKNO SHUTINT F0/13SWITCHPORT MODE TRUNKNO SHUTINT F0/14SWITCHPORT MODE TRUNKNO SHUTEXIT配置以太网通道INT RANGE F0/13 - 14CHANNEL-GROUP 1 MODE ON将VLAN1加入热备组1 INT VLAN 1STANDBY 1

4、 IP 172.16.10.1NO SHUT将VLAN2加入热备组2INT VLAN2STANDBY 2 IP 172.16.20.1NO SHUT将VLAN3加入热备组3INT VLAN 3STANDBY 3 IP 172.16.30.1NO SHUT设置VLAN1和VLAN3分别为热备组1和3的活跃路由器INT VLAN 1STANDBY 1 PRIORITY 105EXITINT VLAN 3STANDBY 3 PRIORITY 105EXIT设置VLAN2为热备组2的备份路由器（不用配置，优先级默认为100，只需将BJ-RS-2的VLAN2分别设置为热备组2的活跃路由器就行了）设置VL

5、AN1有热备组1和3的占先权INT VLAN 1STANDBY 1 PREEMPTINT VLAN 3STANDBY 3 PREEMPT设置热备组1和3的端口跟踪INT VLAN 1STANDBY 1 TRACK F0/15 10EXITINT VLAN 3STANDBY 3 TRACK F0/15 10关闭端口重定向INT VLAN 1 NO IP REDIRECTSEXITINT VLAN 2NO IP REDIRECTSEXITINT VLAN 3 NO IP REDIRECTSEXIT第二台三层交换机的配置命令设置接口IPENCONF THOSTNAME BJ-RS-2IP ROUTI

6、NGINT F0/15NO SWITCHPORTIP ADD 192.168.20.2 255.255.255.252NO SHUTEXITEXIT设置VTP和添加VLANVLAN DATABASEVTP DOMAIN YHLVTP SERVERVTP PASSWORD 321VTP PRUNINGVTP V2VLAN 2 NAME SALESVLAN 3 NAME ENGINEXIT为VLAN配置IPCONF TINT VLAN 1IP ADD 172.16.10.12 255.255.255.0NO SHUTEXITINT VLAN 2IP ADD 172.16.20.12 255.255

7、.255.0NO SHUTEXITINT VLAN 3IP ADD 172.16.30.12 255.255.255.0NO SHUTEXIT配置中继接口INT F0/1SWITCHPORT MODE TRUNKNO SHUTINT F0/2SWITCHPORT MODE TRUNKNO SHUTINT F0/13SWITCHPORT MODE TRUNKNO SHUTINT F0/14SWITCHPORT MODE TRUNKNO SHUTEXIT配置以太网通道INT RANGE F0/13 - 14CHANNEL-GROUP 1 MODE ON将VLAN1加入热备组1 INT VLAN 1

8、STANDBY 1 IP 172.16.10.1NO SHUT将VLAN2加入热备组2INT VLAN2STANDBY 2 IP 172.16.20.1NO SHUT将VLAN3加入热备组3INT VLAN 3STANDBY 3 IP 172.16.30.1NO SHUT设置VLAN2为热备组2的活跃路由器INT VLAN 2STANDBY 2 PRIORITY 105EXIT设置VLAN1和3为热备组1和3的备份路由器（不用配置，优先级默认为100，只需将BJ-RS-1的VLAN1和3分别设置为热备组1和3的活跃路由器就行了）设置VLAN2有热备组2的占先权INT VLAN 2STANDBY

9、 2 PREEMPT设置热备组2的端口跟踪INT VLAN 2STANDBY 2 TRACK F0/15 10EXIT关闭端口重定向INT VLAN 1 NO IP REDIRECTSEXITINT VLAN 2NO IP REDIRECTSEXITINT VLAN 3 NO IP REDIRECTSEXIT二层交换机BJ-S-1的配置ENCONF TNO IP ROUTINGHOSTNAME BJ-S-1设置中继接口INT F0/15SWITCHPORT MODE TRUNKNO SHINT F0/14SWITCHPORT MODE TRUNKNO SH设置VLAN1的管理IPINT VLA

10、N 1IP ADD 172.16.10.13 255.255.255.0NO SHEXITEXIT设置VTP和添加VLANVLAN DATABASEVTP DOMAIN YHLVTP CLIENTVTP PASSWORD 321VTP PRUNINGVTP V2VLAN 2 NAME SALESVLAN 3 NAME ENGINEXIT设置接入接口加入各自VLANCONF TINT F0/1SWITCHPORT ACCESS VLAN 2NO SHEXITINT F0/2SWITCHPORT ACCESS VLAN 3NO SHEXIT二层交换机BJ-S-2的配置ENCONF TNO IP R

11、OUTINGHOSTNAME BJ-S-2设置中继接口INT F0/15SWITCHPORT MODE TRUNKNO SHINT F0/14SWITCHPORT MODE TRUNKNO SH设置VLAN1的管理IPINT VLAN 1IP ADD 172.16.10.14 255.255.255.0NO SHEXITEXIT设置VTP和添加VLANVLAN DATABASEVTP DOMAIN YHLVTP CLIENTVTP PASSWORD 321VTP PRUNINGVTP V2VLAN 2 NAME SALESVLAN 3 NAME ENGINEXIT设置接入接口加入各自VLANC

12、ONF TINT F0/1SWITCHPORT ACCESS VLAN 2NO SHEXITINT F0/2SWITCHPORT ACCESS VLAN 3NO SHEXITPC1的配置ENCONF TNO IP ROUTINGHOSTNAME PC1INT F0/0IP ADD 172.16.20.101 255.255.255.0NO SHUTEXITIP DEFAULT-GATEWAY 172.16.20.1PC4的配置ENCONF TNO IP ROUTINGHOSTNAME PC4INT F0/0IP ADD 172.16.30.102 255.255.255.0NO SHUTEXITIP DEFAULT-GATEWAY 172.16.30.1验证关闭BJ-RS-1的所有接口INT RANGE F0/0 15SHUTDOWN如果VLAN1的PC1仍然能PING通VLAN3的PC3,则说明热备成功设置两个三层交换机为根网桥RS-1SPANNING-TREE VLAN 1 ROOT PRIMARYSPANNING-TREE VLAN 3 ROOT PRIMARYSPANNING-TREE VLAN 2 RO