VJ1638W工程师菜单及维护菜单

1、VJ-1638WVJ-1638W工工程程师师菜菜单单VJ-1638 Diagnosis mode1 (Ver1.03)Check 进入方法：同时按住“”“”“”三个键开机，直到显示“Check1：”Check1:Adj.Platen(调试加热板)Check2:Test(检测)Enter Test1:Ram Capacity(内存容量)128MTest2:Version(版本)Ver.Firm:Parameter:Dip SW:Board ReV:Company code:Seri:机器系列号Test3:PanelEnterPanel1:KeyPanel2:LcdPanel3:LedTest4:

2、Sensor EnterSen.1:CR Orgin OnSen.2:WasteTank OnSen.3:Cover CloseSen.4:M.CoverL CloseSen.5:M.CoverR CloseSen.6:Lever DownSen.7:EdgeAD 6Sen.8:PaperRear 245Sen.9:H.Height lowSen.10:Head1 24Sen.11:Head2 24Sen.12:Trans.1 26Sen.13:Trans.2 26Sen.14:Trans.3 27Sen.15:Trans.4 27Sen.16:I.NTSen.17:I.EDSen.18:I.

3、IDSen.19:Cut SolenoidSen.20:Tank SolenoidSen.21:Tank ValveSen.22:Choke ValveSen.23:Lock SolenoidSen.24:Wiper SolenoidTest5:Encode EnterEncoder1:CR 0000Encoder2:PF 0000Test6:FanEnterFan1:Vacuum FanFan2:Cooling FanFan3:Exhaust FanTest7:Record EnterRecord1:MaintenanceRecord2:ErrorRecord3:Error Init.Rec

4、ord4:PrintRecord5:Ope.TimeRecord6:S/C LogRecord7:S/C LogInitTest8:Head SignalTest9:SpectroVueTest10:Time CheckCheck3:Ink Charge(注墨)EnterNomalLittleCheck4:Adjustment(调整)EnterAdj.1:Rrar/Edge(后测纸/测纸边）Adj.2:Nozzle Check(喷孔检测)Adj.3:Check Skew(检测歪斜)Adj.4:Head Slant(喷头校准)Adj.5:Uni/Bi Low(单/双向 低)EnterUni-D

5、320Uni-D 460Bi-D 320Bi-D 460Adj.6:BiD CopyAdj.7:Uni/Bi Mid(单/双向 中)EnterUni-D 320Uni-D 460Bi-D 320Bi-D 460Adj.8:Uni/Bi High(单/双向 高)EnterUni-D 320Uni-D 460Bi-D 320Bi-D 460Adj.9:Top&Bottom(页边距)Adj.10:Test Print(测试打印)EnterAdjust AllParameter AllLog InfoDot PatternAdj.11:Longstore1(清洗墨路，不可取消)Adj.12:L

6、ongstore2(清洗墨路2，可取消)Adj.13:Count Clear(计数清零)Adj.14:Send Pitch(*)Check5:Cleaning(清洗)EnterTime1:short(轻微清洗)Time2:normal(正常清洗)Time3:long(强力清洗)Check6:Print(打印)EnterAdjust All(打印全部调整项目)Parameter All(打印全部参数项目)Log Info(打印日志信息)Dot Pattern(打印墨点模式)S/C Log InfoCheck7:Parameter(参数）EnterParemeter1:Initialize(初始化

7、)EnterInit.1:Uni/Bi LowInit.2:Uni/Bi MidInit.3:Uni/Bi HighInit.4:MehaParamInit.5:ServoInit.6:HeadInit.7:WiperInit.8:CR MotorInit.9:PF MotorInit.10:PumpInit.11:CutterInit.12:ALLParemeter2:UpDate(修正)EnterUpDate1:Rear/EdgeUpDate2:Head RankUpDate3:Uin/Bi LowUpDate4:Uin/Bi MidUpDate5:Uin/Bi HighUpDate6:M

8、echaParamUpDate7:Charge FlgUpDate8:Debug BitUpDate9:DotCtrlUpDate10:Ink TypeCheck8:Servo(伺服)Enter Servo1:240cps CW320CWEnterEnter320cps CWGPGiGLPFPWM SCALEServo2:240cps CCW320CCWWcEnterEnter320cps CCWGPGIGLPFPWM ScaleServo3:320cps CW460CWWcEnterEnter460cps CWGPGIGLPFPWM ScaleServo4:320cps CCW460CCWW

9、cEnterEnter460cps CCWGPGIGLPFPWM ScaleCheck9:Endurance(耐久)Enter1.CR Motor2.PF Motor3.Cutter4.Pump5.Head Lock6.Nozzle7.Total Life8.CheckEnterSpeed CW Check10:Paper Feed(进纸) EnterFromt:Back:Cut:EenterCheck11:ExControl(事前控制)Check12:Paper InitialVJ-1638 Diagnosis mode2 (Ver1.03)Mainte 进入方法：同时按住“”三个键开机，直

10、到显示“Mainte1：”Mainte.1:Indication(指示）Enter1.Mainte Print number: CR Motor: PF Motor: Pump: Head 1A: Head 1B: Head 1C: Head 1D: Head 1E: Head 1F: Head 1G: Head 1H: Head 2A: Head 2B: Head 2C: Head 2D: Head 2E: Head 2F: Head 2G: Head 2H:Cleaning:Wiper:Cut Number:Cutter Sol:Unlock Pos:2.Print Print1:Num Print2:Area Print3:Effect3.Ope.timeTotal:Normal:Diag:Mainte:Mainte.2:Init Couter(初始化计数器)EnterInit.1:Print NumberInit.2:printIofoInit.3:allInit.4timerInit.5:C