混凝土密封固化剂就是水泥地坪液体硬化剂1

1、混凝土密封固化剂就是水泥地坪渗透液体硬化剂摘要：混凝土密封固化剂基于锂的水泥地坪渗透液体硬化剂，是一种无色，无味，无毒，不易燃，不挥发在美国结晶技术的基础上的水溶液的化合物（VOC）的，它的制剂是使用锂的改性硅酸盐材料，加上独特的高温催化剂乳液形成，高渗透性低碱性的锂基混凝土密封固化剂，以防止混凝土ASR（碱硅酸反应）通过裂解产生的碱硅酸反应膨胀。关键词：纳路特混凝土密封固化剂地坪、捍甲混凝土密封固化剂地面、纳路特混凝土密封固化剂地坪、捍丝混凝土密封固化剂、混凝土密封固化剂作用。混凝土密封固化剂品牌：混凝土密封固化剂品牌有：纳路特、安斯福妙乐、美力实、希尔索丝、力石伯乐、施贝、普罗索、舒尔拉克

2、、捍甲和捍丝混凝土密封固化剂。混凝土密封固化剂可分类为普通混凝土密封固化剂地坪、锂基混凝土密封固化剂和彩色混凝土密封固化剂三大类。 图一：混凝土密封固化剂就是水泥地坪渗透液体硬化剂混凝土密封固化剂1，混凝土密封固化剂简介混凝土密封固化剂：混凝土密封固化剂基于锂的水泥地坪渗透液体硬化剂，是一种无色，无味，无毒，不易燃，不挥发在美国结晶技术的基础上的水溶液的化合物（VOC）的，它的制剂是使用锂的改性硅酸盐材料，加上独特的高温催化剂乳液形成，高渗透性低碱性的锂基混凝土密封固化剂，以防止混凝土ASR（碱硅酸反应）通过裂解产生的碱硅酸反应膨胀。水泥地坪渗透液体硬化剂是活性化学反应型共聚物的倡议有效穿透混

3、凝土3-8mm内，用大量的水合作未完成的钙和镁离子的二氧化硅溶胶，密封硬化混凝土结构，晶体化学永久的反应结合的化学反应，从而增加硬度和混凝土强度，强如钢，光亮如镜的效果处理后形成的。目前在世界上给军事工程和基础设施的广泛应用，是混凝土制品的高科技诊疗技术的新时代，为“专家楼，水泥医生”。锂混凝土密封固化剂功能硬：混凝土密封固化剂处理后的混凝土地面，摩氏硬度达到700度，同比增长约200。磨损：混凝土密封固化剂固化成硬物质的具体的各种部件，耐磨性提高到约40。摩擦：混凝土密封固化剂地坪22.5的干面增加，47.6的增幅潮湿的表面。防灰尘：混凝土密封固化剂发生与混凝土硅酸盐的化学反应，以形成从间隙

4、沉淀致密整体控制灰尘。防滑：混凝土密封固化剂地坪防止盐化成分不从表面析出，以防止打滑和混凝土表面风化。 。抗压力：混凝土密封固化剂由40提高未处理样品后的样品， 抗渗透性：混凝土密封固化剂可以渗透到混凝土锁内的孔隙，抑制水，油和其它污染物进入混凝土。风化：混凝土密封固化剂有效防止紫外线辐射和氯离子，混凝土不会被暴露于电磁或雾的影响。腐蚀：混凝土密封固化剂处理一个月后的混凝土地板，可以大大提高耐腐蚀性，酸完全后十个月。附着力：混凝土密封固化剂地坪附着力和环氧涂料和21.9的增幅结合力基本保持不变。保护力：有一天在混凝土养护过程中，保水率提高94.5，防止开裂。光泽度：混凝土密封固化剂处理过的水泥

5、地面出现大理石般的光泽，更好地利用光泽的时间越长。环保：混凝土密封固化剂无色，无味，不燃，无毒，无VOC的物质。范围：混凝土密封固化剂适用于任何需要改善新旧混凝土的性能。 图二：混凝土密封固化剂就是水泥地坪渗透液体硬化剂2，混凝土密封固化剂反应机理混凝土，水泥和相关材料通过水泥的水泥水合反应具有大量孔的制成其内部结构，钙和石灰（CaO）的不完全水合反应，导致从碱二氧化硅反应混凝土灰尘和水ASR。混凝土密封固化剂渗透混凝土结合自由钙，钾等离子后，不会产生持续的扩张不收缩，稳定的化学共聚物 - 水合硅酸钙，其水泥混凝土最后一组的水合和粘结成的主要成分，铆接孔结构到增加密度，解决水泥地面起尘，降低水

6、的流道结构，有效防止水和腐蚀性化学物质的渗透。由于密实混凝土的自然摩擦或磨削工艺，实现。3，锂基混凝土密封固化剂的物理性质混凝土密封固化剂比重：1.12（20）混凝土密封固化剂冰点：28oF（-2）混凝土密封固化剂沸点：212（100）混凝土密封固化剂颜色：透明混凝土密封固化剂形态：混凝土密封固化剂穿透深度：3-8mm混凝土密封固化剂干燥时间：2-4小时混凝土密封固化剂毒性：无混凝土密封固化剂VOC：无混凝土密封固化剂气味：无混凝土密封固化剂可燃性：无混凝土密封固化剂环境危害：无4，锂混凝土密封固化剂应用：混凝土密封固化剂适用于任何旧的混凝土，水泥砂浆地坪，彩色骨料地板，金刚砂地板，水磨石，自

7、流平地坪1.工业地坪：各类厂，食品厂，植物产品，污水处理厂，纺织厂，制药厂，化工厂，电厂，车库，冷库，仓库等。2.公共土地：公园广场，市政建设，人行道，走廊，图书馆，博物馆，休息室，酒店大堂。3.交通用地：港口，码头，停车场，机场，停机坪上，汽车展厅，机修车间和物流中心。4.商业用地：商业建筑，餐饮酒吧，杂货店，超市，商场，仓库，体育馆，运动场等。5.其它地方：学校，医院，科研机构。图片注意：混凝土密封固化剂不适用于陶瓷，玻璃，金属，木材，橡胶，孔过大的非水泥产品的对象。5，混凝土密封固化剂施工工艺：首先，混凝土密封固化剂施工工艺：新旧地板必须进行研磨，除去浮浆1，混凝土密封固化剂所需要的设备

8、：铣床，吸尘吸水机，擦地机。工具：胶靴，雨刮器，拖把，尘推，并投掷矿泉水瓶，水桶，便携式抛光机。磨：金刚石树脂砂轮（50100300目，500目，1000目，2000目，2，老基面处理：施工前，清洗，清除杂物，油地，依此类推。用水泥修补砂浆嵌缝修复坑洼的地面裂缝，三天后养护施工。3，粗磨：先用水与研磨50碎钻，速度和保持均匀的横磨削方法，直到所有的抛光表面，毛孔打开，然后用吸水机吸所有的水和泥浆;树脂100块加水研磨粉碎，直到50粗通过，彻底消除留下，用吸水机吸干净全是泥和污水研磨划痕，具体情况而定，一般为200目平滑。4.一旦硬化干燥：将固体屏蔽材料0.2KG /平方均匀喷洒在地面上，保持1

9、小时溶液润湿表面，固化，中间至少4小时以上存在与刮水器干燥的地方，继续推滚解决方案，以保证地面完全渗透至完全吸收地面饱和。5，当接到被发现与300粘性溶液磨片水已经渗透完成地面，甚至磨搓掉在地上的剩余材料（白色地面上），而干燥后打磨用吸水机，然后精料遗体500磨片带钢轧机清洁，光滑手摸上去，直到地上爬了起来。6在此期间，当干燥等可以屏蔽第二固体固化剂0.1KG的涂层薄，打磨后固化1-2天后磨，你不能留下残余物的夜晚。7,1-2天，用800 #研磨-2000 -1000干磨干燥直接在地面上研磨，然后机器应尽量控制均匀的研磨后清洁，最后用一个精练抛光速度，各抽吸垫总收率干净，使地面可以出现圆角光泽

10、大理石。8，边角只能处理大机械抛光大面积，使用手持式研磨机进行研磨边加抛光，9.最后，多功能擦地机加百洁布整个浇注干，用吸尘器清除灰尘，地面，此时整体亮度出来10，施工期间要小心，不要跳表，不会留下残留物，初步磨机地面不这样做，尽可能与水，粉碎，研磨时省力，时间，终于收工光明干磨，效果还是不错的。温馨提示：随着时间的推移，地上会达到最佳效果在3-6个月，如果初始原因过早磨接收到的光后期效果不佳，应该是操作的准确掌握。6，混凝土密封固化剂地坪保养：清洁地板时，请使用中性或碱性洗涤剂，不是在地面上使用酸性清洁剂清洗或维护。急救：混凝土密封固化剂食入：口应及时吐出渣，喝大量的水或牛奶，并寻求医疗救助

11、。联系方式：后如皮肤或眼睛接触，立即用肥皂或水，寻求医疗救助。混凝土密封固化剂保证：根据我们的研究机构和其他组织的档案信息有，准确，可靠。但为各种的这种产品和施工条件不能预先估计可能的应用，诸如天气，地理，使用情况，衬底的类型，从而不能进行准确的保修，用户必须进行测试，以使自己的产品适用性强，但超过这个坚固的盾牌不承担责任超出疏忽，绝对的责任和由此造成的损害赔偿责任。solid shield concrete sealer1, IntroductionSolid Shield: lithium-based CS is a colorless, odorless, non-toxic, non-

12、flammable, non-volatile compounds (VOC) in an aqueous solution on the basis of the United States crystallization technology, its formulation is the use of lithium-modified silicate materials Germany, together with the unique high temperature catalyst emulsion formed, high permeability low alkaline l

13、ithium-based concrete sealer to prevent the expansion of concrete ASR (alkali silica reaction) alkali silica reaction produced by cracking.It is an initiative of the active chemical reaction type copolymer effectively penetrate inside the concrete 3-8mm, with plenty of hydration unfinished calcium a

14、nd magnesium ions in a chemical reaction of silica sol, seal hardened concrete structure, crystal chemistry permanent the reaction bonding, increasing the hardness and strength of the concrete, strong as steel, bright as a mirror effect is formed after treatment. Currently in the world to give milit

15、ary engineering and infrastructure widely used, is a new era of high-tech treatment technology of concrete products, as "experts floor, cement doctors."Solid Shield: lithium-based CS featuresKennedy Hard: concrete floor after the treatment, Mohs hardness will reach 700 degrees, increased b

16、y about 200%.Abrasion: the various components of the concrete cured to a hard substance, wear resistance increased to about 40%.Friction: dry surface increase of 22.5%, 47.6% increase wet surface.Anti-Dust: occurs and concrete silicate chemical reaction to form a dense overall control dust precipita

17、ted from the gap.Anti-Slip: prevent salinization ingredient does not precipitate from the surface to prevent slipping and concrete surface efflorescence. .Anti-pressure: the sample after treatment than the untreated sample enhanced by 40%, flexural strength increased by more than 1 times.Anti-permea

18、bility: it can penetrate into the pores inside the concrete lock, inhibiting water, oil and other contaminants into the concrete.Weathering: effectively prevent ultraviolet radiation and chlorine ions, the concrete will not be affected by exposure to electromagnetic or mist.Corrosion: one month afte

19、r treatment the concrete floor, can greatly improve the corrosion resistance, acid completely after ten months.Adhesion: adhesion and epoxy coating and 21.9% increase binding force essentially unchanged.Conservation Force: one day in the concrete curing process, the water retention rate increased 94

20、.5%, to prevent cracking.Bright light: the treated concrete floor appears marble-like sheen, the longer the better use of gloss.Environmental protection: colorless, odorless, non-flammable, non-toxic and non-VOC substances.Scope: apply to any need to improve the performance of old and new concrete.2

21、, Reaction MechanismConcrete, cement and related materials through the cement hydration reaction of cement made of its internal structure with a large number of pores, bleeding passage and incomplete hydration reaction of calcium and lime (CaO), resulting in concrete dust and water from the alkali s

22、ilica reaction ASR.after penetration concrete binding free calcium, potassium and other ions are not generated sustained expansion does not shrink, stable chemical copolymer - hydrated calcium silicate, which is the hydration of cement concrete final set and bonded into the main component, caulking

23、pore structure to increase density, resolve concrete floor dusting, reduce water flow path structure, effectively prevent the penetration of water and corrosive chemicals. Because of dense concrete and after natural friction or grinding process to achieve bright and beautiful effect.(Picture below r

24、edesigned look) 3, the physical properties of lithium-based Specific gravity: 1.12 (20 oC)Freezing Point: 28oF (-2 oC)Boiling point: 212 oF (100 oC)Color: TransparentForm: LiquidPenetration depth: 3-8mmDrying time: 2-4 hoursToxicity: NoneFilm: NoneVOC: NoneOdor: NoneSmoke: NoFlammability: NoneE

25、nvironmental hazards: none4, lithium Applications:This product is suitable for any old concrete, cement mortar floor, colored aggregate flooring, emery flooring, terrazzo, self-leveling floor1. Industrial Floor:Various types of plants, food plants, plant products, sewage treatment plants, cotton mil

26、ls, pharmaceutical plants, chemical plants, power plants, garages, cold storage, warehouses, etc.2. Public Land:Park Plaza, municipal construction, sidewalks, hallways, libraries, museums, lounge, hotel lobbies.3. Transportation Land:Ports, terminals, parking lots, airport, tarmac, car showrooms, ma

27、chine repair workshop and logistics center.4. Commercial Land:Commercial buildings, restaurants bars, grocery stores, supermarkets, shopping malls, warehouse, gym, playground and so on.5. Other places:Schools, hospitals, research institutions.imageNote: does not apply to ceramics, glass, metal, wood

28、, rubber, and the hole is too large non-cement products objects.5, solid shield Construction Technology :First, the construction process: old and new floor must be milled to remove floating pulp1, required equipment: milling machine, vacuum suction machine, wiping machine. Tools: rubber boots, wiper

29、, mop, dust mop, and threw water bottles, buckets, portable polishing machine. Grinding: Diamond resin grinding (50,100,300 mesh, 500 mesh, 1000 mesh, 2000 mesh,2, the old base surface treatment: Before construction, cleaning, clear the ground of debris, oil, and so on. Using cementitious repair mor

30、tar caulking repair potholes and cracks in the ground, and three days later conservation construction.3, coarsely ground: first with water lapping with # 50 diamond pieces, speed and maintain uniform cross-grinding method until all the polished surface, the pores open, then with a suction machine to

31、 suck all the water and mud; resin grinding with 100 # piece grinding with water, until 50 # grinding scratches left by the total elimination of coarse, with a suction machine to suction clean all mud and sewage, the case may be, it is generally 200 mesh smoothed.4. Once the hardener drying: The sol

32、id shield material 0.2KG / square evenly sprayed on the ground, holding 1 hour the solution wetted surface, cured for at least 4 hours in the middle there is a dry place with a wiper over, continue to push roll solution to ensure complete penetration of the ground until fully absorbed ground saturat

33、ed.5, when the receipt was found viscous solution with # 300 grinding mill sheet with water has penetrated completed ground, even grinding to rub off the ground residual material (white on the ground) while grinding after dry with a suction machine, then fine material remains 500 # mill film strip m

34、ill clean, smooth hand feels until the ground up.6 In the meantime, when the mill after drying etc. can shield thin coating of the second solid curing agent 0.1KG, curing 1-2 days after grinding, you can not leave residues night.7,1-2 days, grinding with 800 # # # -2000 -1000 dry grinding dry grindi

35、ng directly on the ground, then the machine should try to control the speed of uniform, each suction clean after grinding, and finally with a scouring polishing pad overall yield clean, so that the ground can appear rounded shiny marble.8, the corners can only handle large mechanical polishing large

36、 areas, use a hand-held grinder for grinding edges plus polished,9. Finally, multi-rubbing machine plus scouring pad entire cast dry, with a vacuum cleaner to clean the dust, the overall brightness of the ground at this time came out10, during the construction period be careful not to jump sheet, do not leave residue, the initial grinding mill ground not to do, as far as possible with water, grinding, grind