VPOSAFE32047可回收瓶装线安全防护标准SafetyCommissioningToolRGBLine

1、Annex 7. VPO.SAFE.3.2.04.7. Safety Safety Commissioning Tool Returnable Glass Bottle Line附件7.VPO.SAFE.3.2.04.7 安全新包装线安全防护标准-可回收瓶装线Version 2第二版2012-05-10Purpose目的4Safety Commissioning Tool for a new RGB (Returnable Glass Bottle) Line. 用于规范新瓶装线（可回收瓶）投产时安全防护标准。用于规范新瓶装线（可回收瓶）投产时安全防护标准。4Tool development

2、标准的建立标准的建立: Modular built. 分类。Containing basic safety AB InBev standards for each module. 符合百威英博的基本安全标准。Easy and user-friendly standardised Audit checklist to be used during commissioning of new Bottle lines by ES or Project Department, applicable for all modules. 在新瓶装线投产期间，ES及项目部门将使用此简单易懂、容易掌握的标准对设

3、备安全进行检查。Modules & Content分类和目录4FLT Loading/Un-loading point叉车装卸点4De-palletiser/Palletiser卸垛机/码垛机4Pallet Stacker/De-stacker托盘码垛机/卸垛机4De-crater/Crater卸箱机/装箱机4Carton former成型机4Carton sealer封箱机4Crate Turner翻箱机4Crate Washer洗箱机4Crate Buffer塑箱提升机4Bottle Washer洗瓶机4Filler装酒机4Tunnel Pasteuriser 隧道式巴式杀菌机4L

4、abeler贴标机4EBI空瓶检验机4Top Sawer割纸箱机4Conveyors输送带4General Requirements一般要求4Acceptance Checklist验收检查清单FLT Loading/Un-loading point 叉车装卸点(1)Attention points关注关注点点:1.Proper protection preventing damages at conveyor from FLT (metal vertical plate or floor plate with FLT wheel stops) 采取适当的保护措施，防止叉车对输送带造成损坏（使

5、用金属材质的垂直挡板或在地面上设置叉车轮阻）2. Ultrasonic sensor to stop the conveyor when FLT approaches or pedestrians approach 设置超声波传感器，当叉车或行人靠近时，停止输送带运行。3. Backplate preventing falling goods during (un-)loading. Avoid gaps between plate and conveyor! 装装/卸载期间，背面设置防护板可防止货物坠落。防护板紧贴输送带，卸载期间，背面设置防护板可防止货物坠落。防护板紧贴输送带，注意防护板紧

6、贴输送带，没有空隙。注意防护板紧贴输送带，没有空隙。123FLT Loading/Un-loading point 叉车装卸点(2)Attention points关注关注点点:4. Chain conveyors: sprocket wheels to be properly guarded avoiding nip points链链式输送带：链轮要防护得当，避免式输送带：链轮要防护得当，避免出现啮合点出现啮合点44FLT Loading/Un-loading point 叉车装卸点(3)Attention points关注关注点点:5. Roller conveyors: sprocket

7、 wheels at the end of the conveyor to be properly guarded avoiding nip points滚筒式输送带：输送带末端的链轮要保护得当，避免出现啮合点。避免出现啮合点。6. Motor cover plates to be fitted against conveyor frame avoiding finger access to chains。在输送带边部安装电机防护盖板，在输送带边部安装电机防护盖板，避免手指碰到链条。避免手指碰到链条。566Modules & Content分类和目录4FLT Loading/Un-lo

8、ading point叉车装卸点4De-palletiser/Palletiser卸垛机/码垛机4Pallet Stacker/De-stacker托盘码垛机/卸垛机4De-crater/Crater卸箱机/装箱机4Carton former成型机4Carton sealer封箱机4Crate Turner翻箱机4Crate Washer洗箱机4Crate Buffer塑箱提升机4Bottle Washer洗瓶机4Filler装酒机4Tunnel Pasteuriser 隧道式巴式杀菌机4Labeler贴标机4EBI空瓶检验机4Top Saw割纸箱机4Conveyors输送带4General

9、Requirements一般要求4Acceptance Checklist验收检查清单De-palletiser/Palletiser 卸垛机/码垛机(1)2mAttention points关注关注点点:1.Access is deterred by fixed fencing of minimum 2m high 至少设置2m高的固定栅栏进行隔离，防止人员进入，固定栅栏完整无空隙，不能让人进入；2. Entrance and exit points of Unit Loads (pallet + goods) are safeguarded with light barriers with

10、 muting system. (Minimum Safety Category 3) 在成垛货物（托盘+货物）的进出口，设置屏蔽系统进行防护（安全类别至少为（安全类别至少为3类）类）- The fixed fences do not allow entrance between the light barrier and the fence 栅栏紧贴光栅栏紧贴光幕幕，光，光幕幕与栅栏之间不能留有空隙让人进入。与栅栏之间不能留有空隙让人进入。- The position of the light barrier does not allow entrance between the light

11、 barrier and the conveyor 光幕光幕紧贴输送带，输送带和紧贴输送带，输送带和光幕光幕之间不能留有空隙让人进入。之间不能留有空隙让人进入。12De-palletiser/Palletiser (2)Attention points:3. Entrance and exit points of empty pallets are safeguarded with fixed fences only allowing a letter box type opening to let an empty pallet pass through.空空托盘进出点的开口应设置足够小，运

12、用邮筒原则托盘进出点的开口应设置足够小，运用邮筒原则只允许托盘出入。只允许托盘出入。4. Entrance and exit points of crates are safeguarded with fixed fences only allowing a letter box typeopening to let a crate pass through. The height of the opening shall never be more than 50cm.塑箱及成品进出点的开口应设置足够小，运用邮筒原则塑箱及成品进出点的开口应设置足够小，运用邮筒原则只允许塑箱或成品出入，高度不

13、得大于只允许塑箱或成品出入，高度不得大于50cm34 Double key system (fortress type) with both a mechanical and electronical lock （See more in next slide） 同时带有机械锁和电子锁的双锁系统(fortress type，见下页图片)- Single key system (with master key on the electrical cabinet or control panel) 单锁系统（配电柜或控制面板上有主钥匙）- A reset command must be given

14、before re-start command is accepted 必须先复位才可以重新启动。必须先复位才可以重新启动。- Interlocks must be robust and not easy to override 联锁装置必须是坚固耐用并不易失灵联锁装置必须是坚固耐用并不易失灵5555Safe Access to Machines-Key system for palletizer and depalletizer 安全进入机器内部安全进入机器内部-钥匙系统钥匙系统-码垛卸垛机码垛卸垛机Normal situation机器正常运机器正常运转状态转状态121Move key 2,

15、 the guarding door can be opened 取下钥匙取下钥匙2，可，可打开防护门打开防护门Move Key 1 ,stop the machine 取下钥匙取下钥匙1，机器，机器停止停止221Put Key 1 into the protection key 将钥匙将钥匙1插入保护插入保护锁中锁中De-palletiser/Palletiser 卸垛机/码垛机 (4)Attention points关关注点注点:6. The machinery shall be equipped with a mechanical blocking device (eventually

16、with electronical sensor) to hold the de-pal/pal in its raised position during maintenance or repair activities.机器应该配有机械的防护装置（配有电子感应器），保证在维护或维修期间卸垛机/堆垛机处于悬空状态时不会掉落下来。Different systems may apply可以使用不同的系统:- Manual system (with bar)- Automatic system手动系统（带有防护杆）自动系统6666De-palletiser/Palletiser 卸垛机/码垛机 (

17、5)Attention points关注关注点点:7. Turntables will be equipped with a fixed plate leaving a gap of maximum 5mm between the fixed plate and the rotating part. In all other occasions, the turntable shall be safeguarded with fixed fencing and an interlocked access door.转向器周围的固定装置与转盘的最大距离不超过5mm。在所有其它情况下，转盘应该通过

18、固定式栅栏和联锁通道门进行防护。7Attention points关注关注点点:8. Roller conveyors: infill plates will be installed at operator working positions and at crossing sections.The gap between the infill plates and rollers shall not exceed 5mm.滚滚轮式输送带：在操作工工作位置轮式输送带：在操作工工作位置及横跨区域安装填充板。及横跨区域安装填充板。填充板及滚轮之间的间隙不应该超填充板及滚轮之间的间隙不应该超过过5

19、mm。9. Conveyor crossing sections shall be equipped with steps with handrails and interlocked gates stopping the conveyor when crossing, and with a reset button re-starting the conveyor (a new start command is not necessary).输送带横跨区域应该配有台阶及扶手，和有人穿过时可以停止输送带运行的联锁门以及可以重新启动输送带的复位按扭（不需要再次按下启动按钮）889De-palle

20、tiser/Palletiser 卸垛机/码垛机 (6)Attention points关关注点注点:10. The operating position shall be designed and constructed in such a way to ensure 100% segregation, by physical means, between the operator and any Fork Lift Truck movement and/or any load handled by a Fork Lift Truck.设计操作工工作位置时，应该借助设计操作工工作位置时，应该

21、借助物理手段确保操作工与移动的叉车物理手段确保操作工与移动的叉车、和、和/或通过叉车控制的任何装载活或通过叉车控制的任何装载活动动100%隔离隔离。10De-palletiser/Palletiser 卸垛机/码垛机 (7)Attention points关关注点注点:11. Moving parts of upper part of palletiser totally screened off 顶部的移动部件都已保护起来。如需开顶部的移动部件都已保护起来。如需开门，应设置联锁开关门，应设置联锁开关11Tunnel guarding隧道式防护Modules & Content分类和目

22、录4FLT Loading/Un-loading point叉车装卸点4De-palletiser/Palletiser卸垛机/码垛机4Pallet Stacker/De-stacker托盘码垛机/卸垛机4De-crater/Crater卸箱机/装箱机4Carton former成型机4Carton sealer封箱机4Crate Turner翻箱机4Crate Washer洗箱机4Crate Buffer塑箱提升机4Bottle Washer洗瓶机4Filler装酒机4Tunnel Pasteuriser 隧道式巴式杀菌机4Labeler贴标机4EBI空瓶检验机4Top Saw割纸箱机4Co

23、nveyors输送带4General Requirements一般要求4Acceptance Checklist验收检查清单Attention points关注关注点点:1. Access is deterred by fixed fencing of minimum 2m high设置至少2m高的固定栅栏进行隔离，防止人员进入；2. Entrance and exit points of empty pallets are safeguarded with fixed fences only allowing a letter boxtype opening to let an empty

24、pallet pass through. 空托盘进出点固定开口应设置足够小，运用邮筒原则只允许托盘出入。只允许托盘出入。3. Entrance / exit points for FLT are safeguarded with light barriers stopping the stacker/de-stacker andConveyor叉车进出点通过设置光电开关进行防护，叉车在此区域工作时可停止堆垛机/卸垛机和输送带的运行。4. Alternatively to point 3, an ultrasonic sensor stopping the stacker/de-stacker

25、and conveyor when FLTapproaches or pedestrians approach might be applied.同第3点类似的防护方法：安装超声传感器，当叉车或路人靠近时同样也可以停止堆垛机/卸垛机和输送带的运行5. Proper protection preventing damages at conveyor from FLT (metal vertical plate or floor plate with FLTwheel stops) 采取适当的保护措施，防止叉车对输送带造成损坏（使用金属材质的垂直挡板或在地面上设置叉车轮阻） 6. Maximum

26、stacking height control sensor is mandatory必须安装最大堆垛高度控制传感器。1254362mPallet Stacker/De-stacker 托盘托盘码垛机码垛机/卸垛机卸垛机Modules & Content分类和目录4FLT Loading/Un-loading point叉车装卸点4De-palletiser/Palletiser卸垛机/码垛机4Pallet Stacker/De-stacker托盘码垛机/卸垛机4De-crater/Crater卸箱机/装箱机4Carton former成型机4Carton sealer封箱机4Crat

27、e Turner翻箱机4Crate Washer洗箱机4Crate Buffer塑箱提升机4Bottle Washer洗瓶机4Filler装酒机4Tunnel Pasteuriser 隧道式巴式杀菌机4Labeler贴标机4EBI空瓶检验机4Top Saw割纸箱机4Conveyors输送带4General Requirements一般要求4Acceptance Checklist验收检查清单De-crater/Crater 卸箱机/装箱机(1)1334Attention points关注关注点点:1.Access at the frontside is deterred by an inter

28、locked screen. (Minimum Safety Category 3) 机器正面防护门上设置联锁开关防止人员进入；(安全类别至少为3类)2. Alternatively to point 1, an open frontside, providing sufficient safety distance and a light barrier . (Minimum Safety Category 3) ,might be applied. 替代第一种方式：正面：需保证安全距离和一个光幕。(安全类别至少为3类)3. Easy access for manual interventi

29、on is made possible by steps 借助台阶能很轻易地接近设备处理故障。4. The screen shall not form any trap hazard for hands or fingers when closed between its lowestposition and the steps当当防护门关闭时，防护门的最低点和台阶之间应没有空隙，避免对手或手指造成伤害。防护门关闭时，防护门的最低点和台阶之间应没有空隙，避免对手或手指造成伤害。2De-crater/Crater 卸箱机/装箱机(2)Attention points关注关注点点:5. Acces

30、s to the machinery shall be provided by interlocked screens. (Minimum Safety Category 3)设置具有联锁开关的防护门以进入机器。（安全类别至少为3类）- Interlocks must be robust and not easy to override联锁开关应该坚固耐用，且不易失效联锁开关应该坚固耐用，且不易失效Different systems may apply可以使用不同的系统:- Manual (depending weight of the screen)手动的（取决于联锁防护门的重量）- Ele

31、ctrical (opening can be by push release, closing must be by continuous push command)电动的（通过“推-放”打开，持续的“推”命令关闭）6. A reset command must be given before re-start command is accepted必须先复位才可以重新启动。必须先复位才可以重新启动。56De-crater/Crater 卸箱机/装箱机(3)Attention points关注关注点点:7. Access at the backside is deterred by fixe

32、d fencing or two photocells (40cm,90cm from the conveyor).机器背面应该设置固定栏栅防止人员进入，或使用两组光电开关，分别距输送带高40cm,90cmAttention points关关注点注点:8. Access to the machinery shall be provided by interlocked access doors. (Minimum Safety Category 3). Access doors must be made accessible by crossing bridges if necessary设置

33、具有联锁开关的防护门以进入机器； (安全类别至少为3类).如需要，应设置横跨桥接近防护门。Different interlock systems may apply可以使用不同的联锁系统:- Double key system (fortress type) with both a mechanical and electronical lock同时配有机械锁和电子锁的双锁系统（ fortress type ）- Single key system (with master key on the electrical cabinet or control panel)单锁系统（配电柜或控制板上

34、带有锁）- A reset command must be given before re-start command is accepted必须先复位才可以重新启动。必须先复位才可以重新启动。- Interlocks must be robust and not easy to override 联锁防护门必须坚固耐用且不易失灵联锁防护门必须坚固耐用且不易失灵7778De-crater/Crater 卸箱机/装箱机(4)Attention points关注关注点点:9. Entrance and exit points of crates are safeguarded with fixed

35、 fences only allowing a letter box typeopening to let a crate pass through. The height of the opening shall never be more than 50cm. If a door is needed on the side guarding, interlock is must. 塑箱进出点的开口处设置固定栅栏进行防护，开口大小只能允许塑箱通过。开口的高度不应高于塑箱进出点的开口处设置固定栅栏进行防护，开口大小只能允许塑箱通过。开口的高度不应高于50CM.如果要在侧面防护上开门，则必须设置

36、联锁开关。如果要在侧面防护上开门，则必须设置联锁开关。999 Interlocks must be robust and not easy to override 联锁装置必须坚固耐用且不易失灵联锁装置必须坚固耐用且不易失灵- A reset command must be given before the re-start command is accepted 必须先复位才可以重新启动。必须先复位才可以重新启动。1Modules & Content分类和目录4FLT Loading/Un-loading point叉车装卸点4De-palletiser/Palletiser卸垛机/

37、码垛机4Pallet Stacker/De-stacker托盘码垛机/卸垛机4De-crater/Crater卸箱机/装箱机4Carton former成型机4Carton sealer封箱机4Crate Turner翻箱机4Crate Washer洗箱机4Crate Buffer 塑箱提升机4Bottle Washer洗瓶机4Filler装酒机4Tunnel Pasteuriser 隧道式巴式杀菌机4Labeler贴标机4EBI空瓶检验机4Top Saw割纸箱机4Conveyors输送带4General Requirements一般要求4Acceptance Checklist验收检查清单C

38、rate Buffer塑箱提升机Attention points:关注点：关注点：1.Access is deterred by fixed fencing of minimum 2m high 设置至少2m高的固定栅栏进行隔离，防止人员进入2. Entrance and exit points of crates are safeguarded with fixed fences only allowing a letter box type opening to let a crate pass through. The height of the opening shall never

39、be more than 50cm.塑箱进出点的开口处设置固定栅栏进行防护塑箱进出点的开口处设置固定栅栏进行防护，开口大小只能允许塑箱，开口大小只能允许塑箱通过。开口高度不得大于通过。开口高度不得大于50cm3. Access to the machinery shall be provided by interlocked access doors.固定栅栏上如需开门，应设置联锁开关:Different interlock systems may apply:可以使用不同种类的联锁- Double key system (fortress type) with both a mechanic

40、al and electronical lock 同时带有机械锁和电子锁的双锁系统- Single key system (with master key on the electrical cabinet or control panel) 单锁系统（配电柜或控制面板上有钥匙）- A reset command must be given before re-start command is accepted 必须先复位才可以重新启动。必须先复位才可以重新启动。- Interlocks must be robust and not easy to override 联锁装置必须是坚固耐用并不

41、易失灵联锁装置必须是坚固耐用并不易失灵4. An access platform with self-closing gate formaintenance and repair purposes shall be installed为维修人员设置的进入平台须设置可以关闭的门43212m Interlocks must be robust and not easy to override 联锁装置应该坚固耐用且不易失灵联锁装置应该坚固耐用且不易失灵- A reset command must be given before the re-start command is accepted必须先

42、复位才可以重新启动。必须先复位才可以重新启动。6. Hatches giving access to the inside of the BW must be fixed (only removable by using tools)洗瓶机观察孔必须是封闭固定的（只能通过工具移除）56665Bottle Washer (3)Attention points关注关注点点:7. Bottle Washer hatches shall be safeguarded by double protection so that a sudden complete opening is made impos

43、sible, avoiding that operators get splashed by caustic洗洗瓶机仓口应该进行双重防护，避免仓门突然打开，致使操作瓶机仓口应该进行双重防护，避免仓门突然打开，致使操作工被碱液溅到。工被碱液溅到。77Bottle Washer (4)Attention points关注关注点点:8. Warning signs for hot surface or hot liquid must be foreseen as from 60C.超过60C热表面或热液体的警示标识必须清晰可见。- All direct accessible hot parts as

44、 from 70C shall be insulated必须将所有可以直接接触到的、超过70C的发热体进行保温。9. Steampipes, direct accessible from ground level, shall ideally be guarded by screens 使用防护屏将通过地面就可以直接接触到的蒸汽管道进行隔离。- Bottle Washers shall be equipped with an H2 extractor ventilator洗瓶机应配有洗瓶机应配有H2抽风机。抽风机。8889Bottle Washer (5)Attention points关关注

45、点注点:10. Access platforms for maintenance and repair purposes along the BW sides shall be equipped with a self-closing access gate 洗瓶机边部用于维护和维修的平台上应设置员工可以手动关闭的门，- The access gate shall never be tightened to the railing in its open position除特殊原因外，门应该一直处于关闭状态除特殊原因外，门应该一直处于关闭状态101010Bottle Washer洗瓶机 (6)

46、 Platform Guardrails: Guardrails are installed on working platforms, they must meet the following safety requirements (Dimensions in millimeter): 1 Handrail 2 Knee rail 3 Kick plate 4 Stanchion 5 Walking level 1 4 5 2 3 Attention points关注关注点点:11. A guardrail shall be installed on the roof of the Bot

47、tle Washer应该在洗瓶机顶部安装护栏。12. The access to the roof shall be provided by a fix stairs. 有合适的阶梯到达洗瓶机顶部。13. The access to the roof shall have a self-closing access gate with lock通向顶部的入口须有门- The access gate shall never be tightened to the railing in its open position，通道门应该一直处于关闭状态11111212Modules & Con

48、tent分类和目录4FLT Loading/Un-loading point叉车装卸点4De-palletiser/Palletiser卸垛机/码垛机4Pallet Stacker/De-stacker托盘码垛机/卸垛机4De-crater/Crater卸箱机/装箱机4Carton former成型机4Carton sealer封箱机4Crate Turner翻箱机4Crate Washer洗箱机4Crate Buffer塑箱提升机4Bottle Washer洗瓶机4Filler装酒机4Tunnel Pasteuriser 隧道式巴式杀菌机4Labeler贴标机4EBI空瓶检验机4Top Sa

49、w割纸箱机4Conveyors输送带4General Requirements一般要求4Acceptance Checklist验收检查清单Filler装酒机 (1)Attention points 关注关注点点:1.The frontside of the Filler shall be safeguarded by fixed screens and only allowing a bottle-shaped gap to let the bottle pass through 装酒机正面应设置固定式防护门进行防护，只留有瓶子装酒机正面应设置固定式防护门进行防护，只留有瓶子大小的间隙以便瓶

50、子通过。大小的间隙以便瓶子通过。2. Movable screens gaining access for maintenance and settings shall be interlocked。(Minimum Safety Category 3) 为方便人员进入维护和设置参数，装酒机设置移动式防护门，应设置联锁开关。（安全类别至少为3类）- Interlocks must be robust and not easy to override 联锁装置必须坚固耐用且不易失灵联锁装置必须坚固耐用且不易失灵- A reset command must be given before the

51、re-start command is accepted 必须先复位才可以重新启动。必须先复位才可以重新启动。-点动器上加急停开关点动器上加急停开关2211112Filler 装酒机 (2)Attention points关注关注点点:3. The backside of the Filler shall be safeguarded by fixed fencing and fixed screens (only removable by using tools) 装酒机背面应该设置固定栅栏和固定防护进行防护（只能通过借助工具进行移除）4. Access doors shall be int

52、erlocked. (Minimum Safety Category 3). Access doors must be made accessible需要进出的防护门应该设置联锁开关，（安全类别为需要进出的防护门应该设置联锁开关，（安全类别为3类）类）且必须是容易进入的。且必须是容易进入的。- Interlocks must be robust and not easy to override 联锁装置必须坚固耐用且不易失灵联锁装置必须坚固耐用且不易失灵- A reset command must be given before the re-start command is accepted

53、. 必须先复位才可以重新启动。必须先复位才可以重新启动。433Extra requirements for all new machines with jog function （Jog for filler and labeler）4For jog function:4Two handed (two pushbutton) jog is required (with spacing of the pushbuttons greater than the distance of the width of a hand to avoid a one handed jog.)4An E-stop

54、should always be included on the jog control station4Only one jog control station (CST) can be enabled at any given time.4Only one safety door can be opened at one time for jog mode to be enabled.4The jog pushbutton station can only be enabled for its visible zone when a guard door is opened. (For e

55、xample, if a guard door is open on the front of a machine, the jog control station on the rear of the machine will not be enabled even though a guard door is opened. This is because the front guard door is out of the visible/safe zone for the rear CST.)4Confirm jog speed is programmed as slow/safe a

56、s possible yet still provide the needed functionality4Sign on machine in local language, (above the location of the CTS): Do not enter machine while the machine is in jog mode. Example of jog with two pushbuttons新设备点动器的要求新设备点动器的要求(适用于灌酒机和贴标机的点动器适用于灌酒机和贴标机的点动器)4点动器点动器:4点动器是双手同时（两个控制按钮）操作点动器是双手同时（两个控制

57、按钮）操作的。的。 (两个按钮的距离大于人手的宽度。避免两个按钮的距离大于人手的宽度。避免一只手操作两个按钮一只手操作两个按钮)。4点动器上需安装急停按钮。点动器上需安装急停按钮。4只在特定情况下激活一个按钮点动控制的模式。只在特定情况下激活一个按钮点动控制的模式。4只有打开一扇安全门时才可以启动点动模式。只有打开一扇安全门时才可以启动点动模式。4当打开的安全门在视线范围内时，才可以启动当打开的安全门在视线范围内时，才可以启动该处的点动模式。该处的点动模式。 (例如：如果在机器正面的安全门打开，点动器例如：如果在机器正面的安全门打开，点动器在机器侧面，无法看到打开的安全门，这种情在机器侧面，无

58、法看到打开的安全门，这种情况下无法启动点动模式。况下无法启动点动模式。 4确认点动速度，在保证功能的情况下越慢确认点动速度，在保证功能的情况下越慢/安安全越好。全越好。4在点动器上方张贴标识：在点动器上方张贴标识：“禁止点动状态下进禁止点动状态下进入机器入机器”。双手操作的点动器例双手操作的点动器例子子Modules & Content分类和目录4FLT Loading/Un-loading point叉车装卸点4De-palletiser/Palletiser卸垛机/码垛机4Pallet Stacker/De-stacker托盘码垛机/卸垛机4De-crater/Crater卸箱机/

59、装箱机4Carton former成型机4Carton sealer封箱机4Crate Turner翻箱机4Crate Washer洗箱机4Crate Buffer塑箱提升机4Bottle Washer洗瓶机4Filler装酒机4Tunnel Pasteuriser 隧道式巴式杀菌机4Labeler贴标机4EBI空瓶检验机4Top Saw割纸箱机4Conveyors输送带4General Requirements一般要求4Acceptance Checklist验收检查清单 Platform Guardrails: Guardrails are installed on working pla

60、tforms, they must meet the following safety requirements (Dimensions in millimeter): 1 Handrail 2 Knee rail 3 Kick plate 4 Stanchion 5 Walking level 1 4 5 2 3 Tunnel Pasteuriser 隧道式巴式杀菌机Attention points关注关注点点:1. The frontside of the tunnel pasteuriser shall be safeguarded by movable screens, protecting operators against burstin