LED灯带测试报告模板

1、说明：本测试报告是我们根据 LED灯带相关标准整理的报告模板，全部是我们原 创，所有工厂或者实验室都可以借鉴使用，可以节省很多时间，因为编制一份模 板还是比较难的，很费时间。这个下载过去，调整一下数据，修改一下公司名称、 地址、报告编号、报告日期、产品名称、产品型号、商标、签发日期，这些都修 改一下，就可以直接使用，报告的格式我们都按照正规测试报告的格式处理好了， 下载即可使用。XXXXX XXXX XXXX Co.,LTDTeSt RePortNo： GLXY190108002RPrOdUCt NameLED STRIPDate of manu facture2018-12-10Model6

2、238-SBatCh nu mberManU factureXXXXX XXXXXXXX Co.,LTDSamPIe qua ntity5Man UfaCtUre AddXXXXXXXBrandSamPIi ng SiteWarehOUSeIn SPeCti on date2019-1-7IEC 60598-2-20:2014 LUminaires - Part 2-20: PartiCUIar requirements - Lighting ChainsIn SPeCti on basisIEC 60598-1:2014+A1:2017LUminaires - Part 1:Gen eral

3、 requireme nts and testsThiS inSPeCtion, InSPeCtion items accord WithIn SPeCti onIEC 60598-1:2014+A1:2017 ,IEC 60598-2-20:2014 Standard requirements.con clusi onDate :2019-1-9REMARKSSamPIe ParameterS XXXXXPage 1 Of21Main Test:AUdit ing:APPrOVaI :1XXXXX XXXX XXXX Co.,LTDTEST REPoRTNo： GLXY190108002RP

4、age 2 of 21IEC60598.1-2014+A1:2017ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCt4Gen eral requireme ntSee BelowLampholders shall be so desig ned and con StrUCted that in no rmal USe they fun Cti on reliably and CaUSe no dan ger to PerS ons or SUrrOU ndin gs.PaSSPIn general, compliance is CheCked by Car

5、rying out all the tests specified.PaSSPIn additi on, the en closure of in depe ndent lampholders shall comply With the requireme nts of IEC 60598-1, in cludi ng the CIaSSifiCati on and mark ing requireme nts of that Sta ndard.PaSSP5Gen eral con diti ons for testsSee Below5.1TeStS accord ing to this

6、Sta ndard are type tests.PaSSPNOTEThe requirements and tolerances Permitted by this Standard arerelated to testing of a type test SamPIe SUbmitted for that purpose.PaSSPComplia nce of the type test SamPIe does not en SUre complia nce of the whole PrOdUCtionof a manUfaCtUrerWith this SafetySta ndard.

7、PaSSPIn additi on to type test ing, con formity of PrOdUCti on is the resp on SibiIity of the man UfaCtUrer and Can in clude rout ine tests and quality assura nce.PaSSP5.2Unl ess OtherWiSe specified, the tests are made at an ambie nt temperature of 21C ±5 ° and With the holder tested asdel

8、ivered and in stalled as in no rmal use.18°CP5.3The tests and in SPeCti ons are Carried out on a total ofPaSSP-nine SPeCime ns for non-SWitChed lampholders, or2 PCSP-12 SPeCime ns for SWitChed lampholdersN/AN/Ain the follow ing order of clauses:N/AN/A-three SPeCimens: CIaUSeS 2 to 13 (except fo

9、r 10.1 and 11.2) and CIaUSeS 15 to 18;N/AN/A-three SPeCime ns: CIaUSe 14 (SWitChed-lampholder tests onl y);N/AN/A-three SPeCime ns: 10.1 and CIaUSeS 19 and 20;N/AN/A-two SPeCime ns: CIaUSe 21 (of WhiCh one SPeCime n for the test of 21.1 and the other for the tests of 21.3 or 21.4);N/AN/A-one SPeCime

10、 n: 21.5 and CIaUSe 22N/AN/AFor testing lampholders With a retention device, the retention device shall be removed.N/AN/ATEST REPoRTNo： GLXY190108002RPage 3 of 21IEC60598.1-2014+A1:2017ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCtFor testi ng lampholders With a rete nti on device accord ing to13.14, t

11、hree additio nalSPeCimens are required With the retention device kept in place.N/AN/AFor testi ng of SCreWIeSS term in als accord ing to 11.2, SeParate SPeCime ns are required in additi on.N/AN/A5.4In CaSe of doubt, gauges, test CaPS and man drels are in troduced into the SPeCime ns,u nl ess OtherWi

12、Se specified, by appl ying the follow ing torques:N/AN/A-0,2 Nm for lampholders E5;N/AN/A-0,2 Nm for lampholders E10;N/AN/A-0,2 Nm for lampholders E14;N/AN/A-0,4 Nm for lampholders E27;N/AN/A-0,8 Nm for lampholders E40.N/AN/A5.5For lampholders E40 With a rated CUrre nt of 32 A, the tests shall be ba

13、sed on this rated CUrre nt.N/AN/A5.6Lampholders are deemed to comply With this Standard if noSPeCimen fails in the complete SerieS of tests SPeCified in 5.3.PaSSPIf one SPeCime n fails in one test, that test and the PreCed ing ones WhiCh may have in flue need the result of that test are repeated on

14、ano ther Set of SPeCime ns to the n Umber required by 5.3, all of WhiCh shall then complyWith the repeatedtests andWith the SUbSeqUe nt tests.PaSSP6Stan dard rati ngsSee BeloW6.1Sta ndard rated voltages are 250 V and 500 V.250VPFor lampholders E14, and for SWitChed lampholders E27, a rated voltage o

15、f 250 V only is alloWed.PaSSPFor lampholders E5 and E10 inten ded for the conn ecti on of SerieS-C onn ected lamps to the supply, the rated voltage shall not exceed 25 V for lampholders E5 and not exceed 60 V for lampholders E10.N/AN/ANOTE 1TheSe VaIUeS refer to the voltage between PartS of differen

16、t polarity. For lampholders E10 intended for the COnneCtiOn of SingIe lamps to the supply, a rated voltage of 250 V only is alloWed.N/AN/ANOTE 2TheSe lampholders are also USed for SUCh SPeCiaI CaSeS as SerieS-C onn ected lamps, Where, becauseof the low n Umber oflamps, 60 V Per lampholder is exceede

17、d.N/AN/ATEST REPoRTNo： GLXY190108002RPage 4 of 21IEC60598.1-2014+A1:2017ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCtWith the excepti on give n for lampholders E5 and E10, the rated voltage shall be not less tha n 250 V. Additi on ally a rated voltage of 125 V is allowed for lampholders E40.N/AN/A6.2S

18、ta ndard rated CUrre nts arePaSSP-0,2 A for lampholders E5;N/AN/A-0,5 A for lampholders E10;N/AN/A-2 A for lampholders E14;N/AN/A-2 A for SWitChed-lampholders E27;N/AN/A-4 A for other lampholders E27;PaSSP-16 A for lampholders E40.N/AN/AThe rated CUrre nt shall be not less tha n the Sta ndard value.

19、PaSSP6.3Lampholders E40 to be USed on 125 V in stallati ons may have an additi onal nominal rati ng of 32 A.N/AN/ANOTEThiS nominal rating COVerS the voltages UP to and inclUding 130 VN/AN/A6.4The rated OPerating temperatUre for lampholders intended forUSe in high temperatUre con diti ons (T marked h

20、olders) shall be not lower tha n 140C°for lampholders E14, not lowerthan 170 Cfor lampholders E27 and n ot lower than 230C foflampholders E40.190 f CPNOTEThe rated OPerat ing temperatUres for EdiS on SCreW lampholdersWithOUt T marking are given in IEC 60598-1,N/AN/AThey arePaSSP-135 C for lamph

21、olders E14;N/AN/A-165 C for lampholders E27;165P-225 C for lampholders E40.N/AN/A7CIaSSifiCati onSee BelowLampholders are CIaSSified as defined in 7.1 to 7.6.PaSSP7.1ACCOrding to the material of the external parts:PaSSP-lampholders of inSUlating material;N/AN/A-metal lampholders.PaSSPNOTELamPholders

22、With external PartS conSiSting PartIy of metal andlampholders COmPriSing external PartS of inSUlating material With a con dUCtive OUter SUrfaCe, for example a metallized OUter shell, are con Sidered as metal lampholders (See 13.3).PaSSPTEST REPoRTNo： GLXY190108002RPage 5 of 21IEC60598.1-2014+A1:2017

23、ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCtThiS does not apply to threaded entries and external parts, for example a metal Shade ring moun ted onto the OUtSide of a lampholder of insulating material, WhiCh CannOt become live eve n in the CaSe of an in SUIati on fault. Metal holders With insulating C

24、OVerings are conSidered as metal lampholders.PaSSPIn order to CheCk Whether or not a SUrfaCe is con ductive, two StriPe-electrodes 1,5 mm wide, 25 mm long and With a distance of 2 mm from each other are applied to the SUrfaCe (e.g. With SiIVer conductive Paint). In accordance With 15.4, the insulati

25、ng resista nce is measured betwee n the stripes. The SUrfaCe is conSidered to be conductive if the resistance is less than 5 MQ .573M QP7.2ACCOrd ing to degree of PrOteCti on aga inst in gress of water:PaSSP-ordinary lampholders;N/AN/A-drip-proof lampholders.PaSSP7.3ACCOrd ing to method of fixing:Pa

26、SSP-threaded entry lampholders;N/AN/A-COrd-grip lampholders;N/AN/A-backplate lampholders;N/AN/A-Other lampholders.PaSSPNOTEEXamPIeS of other lampholders are lampholders PrOVided With a mecha ni cal SUSPe nsion device, e.g. A hook.PaSSP7.4ACCOrd ing to type:PaSSP-SWitChed-lampholders,PrOVided With an

27、 integral SWitCh tocon trol the SUPPIy to the lamp;N/AN/A-non-SWitChed lampholders.PaSSP7.5ACCOrd ing to PrOteCti on aga inst electric shock:PaSSP-Unen closed lampholders;N/AN/A-en closed lampholders;N/AN/A-in depe ndent lampholders;N/AN/A-PartIy rein forced in SUIated lampholders;N/AN/A-en closed r

28、ei nforced in SUIated lampholders.PaSSPNOTEWhere a lampholder is USed With a work ing voltage of 50 % or less of its maximum rati ng, it Can be regarded as equivale nt to a reinforced inSUIated lampholder.PaSSP7.6ACCOrd ing to resista nce to heat:PaSSPTEST REPoRTNo： GLXY190108002RPage 6 of 21IEC6059

29、8.1-2014+A1:2017ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCt-lampholders for rated OPerating temperatures UP to the IimitS give n in 6.4;PaSSP-lampholders for OPerati ng in high temperature con diti ons (T marked holders).N/AN/A8Marki ngSee Below8.1Lampholders, other than lampholders E5 and E10, shal

30、l be marked With the followi ng:PaSSP-rated CUrre nt, i n amperes;1.8AP-rated voltage, in volts, and rated pulse voltage, in kV, if higher tha nPaSSP? 2,5 kV for lampholders rated 250 V,250V2.5kVP? 4 kV for lampholders rated 500 V;N/AN/AThe rated pulse voltage of the lampholder (i n kV) should eithe

31、r be marked on the lampholder or made available in the manUfaCtUrer ' S catalogue or the like.N/AN/ANOTE 1Some lampholders still show rated voltages higher tha n 500 V.ThiS is an earlier Way of express ing the PermiSSibIe pulse voltageVia a rated voltage. For SUCh lampholders, the CreePage dista

32、 nces and CIeara nces Can be found in IEC 60598-1.N/AN/Asymbol for natureof CUrrent,if required (for SWitChedlampholders onl y);N/AN/Amark of origin (this may take the form of a trade mark, manUfaCtUrer's identification markor the n ame of the resp on sible Ven dor);FIVESTARSCRYSTALP-type refere

33、n ce;6238-SPAVaiIabIe technical documentation of the manUfaCtUrer like Pri nted catalogues or on Ii ne catalogues should allow a clear identification of a lampholder either by a Unique catalogue n Umber or by an ide ntify ing refere nce on the holder, SPeCify ing the esse ntial CharaCteriStiC featur

34、es and the basic desig n of the PrOdUCt SUPPIeme nted by a clear descripti on. Variati ons of the basic desig n like for example differe nt cable Ien gth, fixing means, colours etc., WhiCh do not affect Safety or PerfOrma nce of the lampholder, Can be disregarded in the type reference marked on the

35、product. Variations inCIUded in the type testi ng PrOCedUre are IiSted in the COrreSP Onding test reports.N/AN/ATEST REPoRTNo： GLXY190108002RPage 7 of 21IEC60598.1-2014+A1:2017ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCt the degree of PrOteCti on aga inst in gress of Water for drip-proof lampholders;

36、IP20P-rated OPerati ng temperature "T", i ndicat ing the highest OPerati ng temperature, if applicable.N/AN/AThe marki ng of the rated OPerati ng temperature is n ot required for lampholders whose exterior is made wholly of CeramiC material. For these lampholders, this in formati on, if ap

37、plicable, shall either be marked on the lampholder or be made available in the man UfaCtUrer's catalogue.N/AN/AFor lampholders accord ing to this Sta ndard, the dista nces for impulse WithSta nd CategOry II are usually applicable. For holders in equipme nt Where a higher degree of availability i

38、s expected, dista nces for impulse WithSta nd CategOry III may be applicable. ThiS in formati on shall be in dicated in the man UfaCtUrer's catalogue or the like.N/AN/AEn closed rei nforced in SUIated lampholders offer an adequate level of PrOteCtion for USe in luminaires Where they are accessib

39、le in no rmal use. ThiS in formati on shall be in dicated in the manUfaCtUrer ' S catalogue or the like.N/AN/AFor PartIy rein forced in SUIated lampholders, SUffiCie nt CreePage dista nces and CIeara nces to outer accessible SUrfaCeS will require additi onal PrOteCti on to some PartS of the lamp

40、holder by the lum in aire desig n or by USe of additi onal attachme nt(s) or COVer(s). ThiS information shall be indicated in the manUfaCtUrer ' S catalogue or the like.N/AN/ALamPholders E10 shall be marked With the follow ing:N/AN/A-rated voltage, in volts;N/AN/A-mark of orig in;N/AN/A-type ref

41、eren ce;N/AN/A-mark of orig in;N/AN/A-type referen ce.N/AN/A8.2If symbols are USed for CUrre nt and voltage, A shall denote amperes and V volts. Alter natively, for volt and ampere rati ngs, figures may be USed alone, the figure for the ratedCUrrent being marked before or above that for the rated vo

42、ltage and SeParated from the Iatter by an oblique StrOke or line.PaSSPTEST REPoRTNo： GLXY190108002RPage 8 of 21IEC60598.1-2014+A1:2017ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCtTherefOre the marking of CUrrent and voltage may be as follows: 22 A 250 V Or 2/250 r.2501.8A/250VPThe symbol for direct CU

43、rre nt shall be (IEC 60417-5031:2002-10).N/AN/AThe symbol for PrOteCti on aga inst in gress of Water for drip-proof lampholders shall be IPX1.IP21PNOTEWhere X is USed in the IP n Umber it in dicates a miss ing n UmeraI in the example, but both the appropriate n UmeraIS in accorda nce With IEC 60529

44、are marked.PaSSPThe Ietter T shall be followed by the value of the rated OPerati ng temperature in degrees Celsius.N/AN/A8.3The marking of the degree of PrOteCti on aga inst in gress of Water shall be on the OUtSide of the holder.PaSSP8.4An earth ing term inal shall be in dicated by the symbol (IEC

45、60417-5019:2002-10).PThiS symbol shall not be PIaCed on screws, removable WaSherS or other easily removable parts.PaSSP8.5Marking shall be durable and easily legible.PaSSPComplia nce is CheCked by in SPeCti on and, after the tests of CIaUSe 19 have bee n completed, by trying to remove the marking by

46、 rubbing lightly for 15 S With a PieCe of cloth SOaked With Water and for a further 15 S With a PieCe of cloth SOaked With petroleum spirit.PaSSPNOTEThe petroleum SPirit USed typically con SiStS of a solve nt hexa neWith a COntent of aromatics of maximum 0,1 volume PerCe ntage,a kauri-buta nolvalue

47、of 29, an in itial boili ng-po intofapproximately 65C, a dry-po int of approximately 69C and a3SPeCifiC den Sity of approximately 0,68 g/cm.PaSSP9Dime nsionsSee Below9.1LamPholders E10, E14, E27 and E40 shall comply With the CUrrent edition of the Standard SheetS of the IEC 60061 series.PaSSPThe mi

48、ni mum dime nsions of the SCreW thread and dime nsion X shall be CheCked by means of gauges accord ing to Stan dard SheetS 7006-25 (E10, E14 and E40) and 7006-25A (E27), and by means of the gauge accord ing to Stan dard Sheet 7006-26 of IEC 60061-3.PaSSPTEST REPoRTNo： GLXY190108002RPage 9 of 21IEC60

49、598.1-2014+A1:2017ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCt9.2Lampholders shall allow in Serti on of all COrreSP Onding lamps so as to make con tact.PaSSPComplia nce is CheCked by means of gauges accord ing to the CUrrent edition of the following Standard SheetS of IEC 60061-3 and accord ing to th

50、e in dicati ons of these sheets:PaSSP-lampholders E14: 7006-30 and 7006-31;N/AN/A-Candle lampholders E14: 7006-30A and 7006-31;N/AN/A-lampholders E27: 7006-21 and 7006-22A;PaSSP-lampholders E40: 7006-23 and 7006-24.N/AN/APending gauges for lampholders E5 and E10, the con tact-mak ing is CheCked by m

51、eans of theCOrreSP Onding lamps. It is PreSUmed that the man UfaCtUrer of the lampholder for the PUrPOSe of the test delivers the lamps for WhiCh the lampholder is inten ded.N/AN/AIf the fixing means of lampholders are integrated PartS of the rim and the lampholder is desig ned for USe With a SeIeCt

52、ed Standardized lamp only, PartS of the lampholder rim could in terfere With the releva nt con tact-mak ing gauge. In this case, compliance With the requirements for maximum lamp outlines according to IEC 60630 for the lamp indicated in the lampholder manUfaCtUrer's inStrUCtions shall be checked

53、. Follow ing this CheCk ing, the con tact-mak ing gauge shall be applied after those PartS of the lampholder interfering With the gauge have bee n removed.N/AN/AFor test ing SUCh lampholders, two additi onal SPeCime ns specially PrePared to accept the releva nt con tact-mak ing gauge are required.N/

54、AN/A9.3The following dimensionsshall be not less than the VaIUeSshow n.Ring thick ness:0.30mmPNOTE 1ThiCk nesses are measured by means of a micrometer With poin ted no SeS and ratchet screw.PaSSPFor the SCreW shell, two SetS of three measurements are made, each Set Carried out on one of two differen

55、t generating lines of the SCreW shell. The mean value of the SiX measurements shall be at least equal to the SPeCified value.PaSSPTEST REPoRTNo： GLXY190108002RPage 10 of 21IEC60598.1-2014+A1:2017ClaUSeReqUireme nt-TestReSUIt-RemarkVerdiCt9.4The effective len gth of SCreW en gageme nt, if any, of outer shell and dome shall meet one of the followi ng requireme nts Whereby the en gageme nt shall always be over one full tur n.Either the effective len gt