网络设备安装与调试实习报告

1、.课程实习报告课程名称：网络设备安装与调试实习专业：计算机控制技术102 小组成员：李长源 刘亚运 指导老师：刘宇 陈顺立 何胤 实习地点：计算机实训机房 实习时间：2011年12月19日-23日实习目的与任务：1.实习目的：2.实习任务：序列号实习内容任务要求实习内容一网络互通综合实验1. 根据网络拓扑图连接设备2. 根据网络拓扑图配置各网络设备IP3. 配置RIP路由器协议使网络互通实习内容二三个路由器互通配置1.通过配置动态路由协议（RIP或OSPF）后网络互通。2.根据实际情况给网络拓扑图打上标签实习内容三九个路由器互通配置1.通过配置动态路由协议（RIP或OSPF）后网络互通。2.根

2、据实际情况给网络拓扑图打上标签实习内容四PPP-PAP实验1.根据拓扑图，在模拟器中添加网络设备，并给指定端口配置IP信息。2.分别给ROUTER0、ROUTER1、ROUTER2、ROUTER3指定用户名和密码（用户名和密码自定），封装PAP协议，希望DCE端对DTE端（ROUTER0、ROUTER1、ROUTER2、ROUTER3）进行身份验证。3.给各PC机配置相应的IP信息（IP地址自定），测试PC0、PC1、PC2、PC3、PC4之间的网络互通状况。任务一对三层交换机与路由器vlan的配置对三层交换机上vlan的配置创建VlanSwitch>enSwitch#configCon

3、figuring from terminal, memory, or network terminal? Enter configuration commands, one per line. End with CNTL/Z.Switch(config)#vlan 2Switch(config-vlan)#exitSwitch(config)#vlan 3Switch(config-vlan)#exitSwitch(config)#vlan 4Switch(config-vlan)#exitSwitch(config)#vlan 5Switch(config-vlan)#exit给Vlan划分

4、端口：Switch(config)#int f 0/2Switch(config-if)#switchport access vlan 2Switch(config-if)#exitSwitch(config)#int f 0/3Switch(config-if)#switchport access vlan 3Switch(config-if)#exitSwitch(config)#int f 0/4Switch(config-if)#switchport access vlan 4Switch(config-if)#exitSwitch(config)#int f 0/5Switch(co

5、nfig-if)#switchport access vlan 5Switch(config-if)#exitSwitch(config)#int vlan 2%LINK-5-CHANGED: Interface Vlan2, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to upSwitch(config-if)#ip address 192.168.2.1 255.255.255.0Switch(config-if)#no shutSwitch(config-

6、if)#exitSwitch(config)#int vlan 3%LINK-5-CHANGED: Interface Vlan3, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan3, changed state to upSwitch(config-if)#ip address 192.168.3.1 255.255.255.0Switch(config-if)#no shutSwitch(config-if)#exitSwitch(config)#int vlan 4%LINK-5-CHANGE

7、D: Interface Vlan4, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan4, changed state to upSwitch(config-if)#ip address 192.168.4.1 255.255.255.0Switch(config-if)#no shutSwitch(config-if)#exitSwitch(config)#int vlan 5%LINK-5-CHANGED: Interface Vlan5, changed state to up%LINEPRO

8、TO-5-UPDOWN: Line protocol on Interface Vlan5, changed state to upSwitch(config-if)#ip address 192.168.5.1 255.255.255.0Switch(config-if)#no shutSwitch(config-if)#exitSwitch(config)#Switch(config)#%LINK-5-CHANGED: Interface FastEthernet0/24, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on I

9、nterface FastEthernet0/24, changed state to upSwitch(config)#int f 0/24Switch(config-if)#no switchport%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to upSwitch(config-if)#ip addre

10、ss 10.1.1.2 255.255.255.0Switch(config-if)#no shutSwitch(config-if)#exit给三层交换机rip配置Switch(config)#router ripSwitch(config-router)#network 10.1.1.0Switch(config-router)#network 192.168.2.0Switch(config-router)#network 192.168.3.0Switch(config-router)#network 192.168.4.0Switch(config-router)#network 1

11、92.168.5.0三层交换机的状态Switch#sh runBuilding configuration.Current configuration : 1616 bytesversion 12.2no service timestamps log datetime msecno service timestamps debug datetime msecno service password-encryptionhostname Switchinterface FastEthernet0/1 no switchport ip address 10.1.1.2 255.255.255.0 d

12、uplex auto speed autointerface FastEthernet0/2 switchport access vlan 2interface FastEthernet0/3 switchport access vlan 3interface FastEthernet0/4 switchport access vlan 4interface FastEthernet0/5 switchport access vlan 5interface FastEthernet0/6interface FastEthernet0/7interface FastEthernet0/8inte

13、rface FastEthernet0/9interface FastEthernet0/10interface FastEthernet0/11interface FastEthernet0/12interface FastEthernet0/13interface FastEthernet0/14interface FastEthernet0/15interface FastEthernet0/16interface FastEthernet0/17interface FastEthernet0/18interface FastEthernet0/19interface FastEther

14、net0/20interface FastEthernet0/21interface FastEthernet0/22interface FastEthernet0/23interface FastEthernet0/24 no switchport no ip address duplex auto speed autointerface GigabitEthernet0/1interface GigabitEthernet0/2interface Vlan1 no ip address shutdowninterface Vlan2 ip address 192.168.2.1 255.2

15、55.255.0interface Vlan3 ip address 192.168.3.1 255.255.255.0interface Vlan4 ip address 192.168.4.1 255.255.255.0interface Vlan5 ip address 192.168.5.1 255.255.255.0router rip network 10.0.0.0 network 192.168.2.0 network 192.168.3.0 network 192.168.4.0 network 192.168.5.0ip classlessline con 0line vt

16、y 0 4 login对router2的配置Router>enRouter#configConfiguring from terminal, memory, or network terminal? Enter configuration commands, one per line. End with CNTL/Z.Router(config)#int f 0/0Router(config-if)#ip address 10.1.1.1 255.255.255.0Router(config-if)#no shut%LINK-5-CHANGED: Interface FastEthern

17、et0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config-if)#exitRouter(config)#int s 1/0Router(config-if)#ip address 61.1.1.1 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial1

18、/0, changed state to downRouter(config-if)#exitRouter(config)#router ripRouter(config-router)#network 10.1.1.0Router(config-router)#network 61.1.1.0Router(config-router)#Router2的状态Router#sh runBuilding configuration.Current configuration : 852 bytes version 12.2no service timestamps log datetime mse

19、cno service timestamps debug datetime msecno service password-encryptionhostname Routerinterface FastEthernet0/0 ip address 10.1.1.1 255.255.255.0 duplex auto speed autointerface FastEthernet0/1 no ip address duplex auto speed auto shutdowninterface Serial1/0 ip address 61.1.1.1 255.255.255.0interfa

20、ce Serial1/1 no ip address shutdowninterface Serial1/2 no ip address shutdowninterface Serial1/3 no ip address shutdowninterface Serial1/4 no ip address shutdowninterface Serial1/5 no ip address shutdowninterface Serial1/6 no ip address shutdowninterface Serial1/7 no ip address shutdownrouter rip ne

21、twork 10.0.0.0 network 61.0.0.0ip classlessline con 0line vty 0 4 loginrouter2和router3联通的配置：对router3进行时钟配置Router(config)#interface s1/0Router(config-if)#cloCk RATE 64000 Router(config-if)#exit对router3的配置Router>enRouter#configConfiguring from terminal, memory, or network terminal? Enter configurat

22、ion commands, one per line. End with CNTL/Z.Router(config)#int f 0/0Router(config-if)#ip address 172.17.1.1 255.255.255.0Router(config-if)#no shut%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(

23、config-if)#exitRouter(config)#int s 1/0Router(config-if)#ip address 61.1.1.2 255.255.255.0Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial1/0, changed state to upRouter(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to upRouter(config-if)#eixt % Invalid

24、 input detected at '' marker.Router(config-if)#exitRouter(config)#router ripRouter(config-router)#network 61.1.1.0 Router(config-router)#network 172.17.1.0Router3的状态Router#sh runBuilding configuration.Current configuration : 874 bytesversion 12.2no service timestamps log datetime msecno serv

25、ice timestamps debug datetime msecno service password-encryptionhostname Routerinterface FastEthernet0/0 ip address 172.17.1.1 255.255.255.0 duplex auto speed autointerface FastEthernet0/1 no ip address duplex auto speed auto shutdowninterface Serial1/0 ip address 61.1.1.2 255.255.255.0 clock rate 6

26、4000interface Serial1/1 no ip address shutdowninterface Serial1/2 no ip address shutdowninterface Serial1/3 no ip address shutdowninterface Serial1/4 no ip address shutdowninterface Serial1/5 no ip address shutdowninterface Serial1/6 no ip address shutdowninterface Serial1/7 no ip address shutdownro

27、uter rip network 61.0.0.0 network 172.17.0.0ip classlessline con 0line vty 0 4 loginendPC1，PC2，PC3，PC4的配置与连通性PC1的配置PC4的配置连通性任务二路由器的配置Router3命令：Router(config)#int f 0/0Router(config-if)#ip add 10.1.3.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int f 0/1Router(config-i

28、f)#ip add 10.1.1.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int f 1/1Router(config-if)#ip add 192.168.1.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#router ripRouter(config-router)#network 192.168.1.0Router(config-router)#network 10.1.3.0Router(config-r

29、outer)#network 10.1.1.0 Router0命令：Router(config)#int f 1/0Router(config-if)#uip add 10.1.2.1 255.255.255.0Router(config-if)#ip add 10.1.2.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int f 1/1Router(config-if)#ip&

30、#160;add 192.168.2.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#int f 0/0Router(config-if)#ip add 10.1.3.2 255.255.255.0Router(config-if)#no shutRouter(config)#router ripRouter(config-router)#network 10.1.3.0Router(config-router)#ne

31、twork 10.1.2.0Router(config-router)#network 192.168.2.0对路由器Router1作如下配置：Router1命令：Router(config)#int f 1/1Router(config-if)#ip add 192.168.3.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int f0/1Router(config-if)#ip add 10.1.1.2 255.255.255.0Router(config-if)

32、#no shutRouter(config-if)#exitRouter(config)#int f1/0Router(config-if)#ip add 10.1.2.2 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#router ripRouter(config-router)#network 10.1.2.0Router(config-router)#network 192.168.3.0Router(config-router)#network 10.1.1.0IP的配置通信的联通情

33、况任务三左边部分路由器配置对Router6的配置Router#configure Router#configure terminal Router(config)#int f 0/0Router(config-if)#ip add 10.1.6.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int f 0/1 Router(config-if)#ip add 192.168.1.1 255.255.255.0Router(config-if)#no shutRouter(config-i

34、f)#exitRouter(config)#router ripRouter(config-router)#network 192.168.1.0Router(config-router)#network 10.1.6.0Router6状态Router#show runBuilding configuration.Current configuration : 482 bytesversion 12.2no service timestamps log datetime msecno service timestamps debug datetime msecno service passwo

35、rd-encryptionhostname Routerinterface FastEthernet0/0 ip address 10.1.6.1 255.255.255.0 duplex auto speed autointerface FastEthernet0/1 ip address 192.168.1.1 255.255.255.0 duplex auto speed autorouter rip network 10.0.0.0 network 192.168.1.0ip classless对Router3的配置Router#configure terminal Router(co

36、nfig-if)#ip add 10.1.7.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int f 0/0Router(config-if)#ip add 192.168.2.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exit Router(config)#router ripRouter(config-router)#network 192.168.2.0Router(config-router)#netwo

37、rk 10.1.7Router3的状态Router#show runBuilding configurationCurrent configuration : 482 bytesversion 12.2no service timestamps log datetime msecno service timestamps debug datetime msecno service password-encryptionhostname Routerinterface FastEthernet0/0 ip address 10.1.7.1 255.255.255.0 duplex auto sp

38、eed autointerface FastEthernet0/1 ip address 192.168.2.1 255.255.255.0 duplex auto speed autorouter rip network 10.0.0.0 network 192.168.2.0ip classlessline con 0line vty 0 4 loginEnd对PC1的配置对PC0的配置PC1和PC0的联通状态对右半部分路由器配置对Router4的配置Router#configure terminal Router(config)#int f 1/0Router(config-if)#ip

39、 add 10.1.2.2 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#ont f 0/1Router(config)#int f 0/1Router(config-if)#ip add 10.1.3.2 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int f 0/0Router(config-if)#ip add 10.1.1.2 255.255.255.0Router(config

40、-if)#no shutRouter(config-if)#exitRouter(config)#router ripRouter(config-router)#network 10.1.3.0Router(config-router)#network 10.1.2.0Router(config-router)#network 10.1.1.0Router4的状态Router#sh runBuilding configuration.Current configuration : 624 bytesversion 12.2no service timestamps log datetime m

41、secno service timestamps debug datetime msecno service password-encryptionhostname Routerinterface FastEthernet0/0 ip address 10.1.3.2 255.255.255.0 duplex auto speed autointerface FastEthernet0/1 ip address 10.1.1.2 255.255.255.0 duplex auto speed autointerface FastEthernet1/0 ip address 10.1.2.2 2

42、55.255.255.0 duplex auto speed autointerface FastEthernet1/1 no ip address duplex auto speed auto shutdownrouter rip network 10.0.0.0ip classlessline con 0line vty 0 4 loginPC3对PC1， PC2和PC4的联通状态任务四Router0的配置与状态Router>enRouter#confConfiguring from terminal, memory, or network terminal? Enter confi

43、guration commands, one per line. End with CNTL/Z.Router(config)#interfa f 0/0Router(config-if)#ip add 192.168.1.1 255.255.255.0Router(config-if)#no shut%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upR

44、outer(config-if)#exitRouter(config)#interfa s 1/0Router(config-if)#ip add 1.1.1.1 255.255.255.0Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial1/0, changed state to upRouter(config-if)#exitRouter(config)#router ripRouter(config-router)#network 192.168.1.0Router(config-router)#network 1.1.1

45、.0Router(config-router)#exitRouter(config)#interf s 1/0Router(config-if)#encap pppRouter(config-if)#ppp pap sent-us router0 password 000Router(config-if)#exitRouter(config)#Router#show runBuilding configuration.Current configuration : 770 bytesversion 12.2no service timestamps log datetime msecno se

46、rvice timestamps debug datetime msecno service password-encryptionhostname Routerusername router0 password 0 1 starinterface FastEthernet0/0 ip address 192.168.1.1 255.255.255.0 duplex auto speed autointerface FastEthernet0/1 no ip address duplex auto speed auto shutdowninterface Serial1/0 ip addres

47、s 1.1.1.1 255.255.255.0 encapsulation ppp ppp pap sent-username router0 password 0 000interface Serial1/1 no ip address shutdowninterface Serial1/2 no ip address shutdowninterface Serial1/3 no ip address shutdownrouter rip network 1.0.0.0 network 192.168.1.0ip classlessline con 0line vty 0 4 login -

48、MoreRouter1的配置与状态Router>Router>enRouter#confConfiguring from terminal, memory, or network terminal? Enter configuration commands, one per line. End with CNTL/Z.Router(config)#interfa f 0/0Router(config-if)#ip add 192.168.2.1 255.255.255.0Router(config-if)#no shut%LINK-5-CHANGED: Interface Fast

49、Ethernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config-if)#exitRouter(config)#interfa s 1/0Router(config-if)#ip add 2.2.2.1 255.255.255.0Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial1/0, changed state to upRouter

50、(config-if)#exitRouter(config)#router ripRouter(config-router)#network 192.168.2.0Router(config-router)#network 2.2.2.0Router(config-router)#exitRouter(config)#interf s 1/0Router(config-if)#encap pppRouter(config-if)#ppp pap sent-us router1 password 000Router(config-if)#exitRouter(config)#Router#sho

51、w runBuilding configuration.Current configuration : 689 bytesversion 12.2no service timestamps log datetime msecno service timestamps debug datetime msecno service password-encryptionhostname Routerinterface FastEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex auto speed autointerface FastEth

52、ernet0/1 no ip address duplex auto speed auto shutdowninterface Serial1/0 ip address 2.2.2.1 255.255.255.0interface Serial1/1 no ip address shutdowninterface Serial1/2 no ip address shutdowninterface Serial1/3 no ip address shutdownrouter rip network 2.0.0.0 network 192.168.1.0 network 192.168.2.0ip

53、 classlessline con 0line vty 0 4 loginend -MoreRouter4的配置与状态Router>enRouter#confConfiguring from terminal, memory, or network terminal? Enter configuration commands, one per line. End with CNTL/Z.Router(config)#interf s1/0Router(config)#interface f 0/0Router(config-if)#ip add 172.17.1.2 255.255.2

54、55.0Router(config-if)#no shutRouter(config)#Router(config)#Router(config)#interf s1/0Router(config-if)#ip address 1.1.1.2 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutRouter(config-if)#exitRouter(config)#interf s1/1Router(config-if)#ip address 2.2.2.2 255.255.255.0Router(c

55、onfig-if)#clock rate 64000Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial1/1, changed state to downRouter(config-if)#exitRouter(config)#Router(config)#interf s1/2Router(config-if)#ip address 3.3.3.2 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial1/2, changed state to downRouter(config-if)#exitRouter(config)#interf s1/3Router(config-if)#ip address 4.4.4.2 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shut%L