汽车行业英文缩写2

1、OTS=off tooling samples 即全工装状态下非节拍生产条件下制造出来的样件.用于验证产品的设计能力.(用于验证设计出来的产品是否符合客户要求，同时也是对生产工装的验证)同时OTS也可以叫模具样品。 LH 要求汇总书(一个项目的所有资料)TPB 产品技术描述(图纸、技术供货条件等等)DKM 数据控制模型(汽车形状1:1的基准样车)P P认可计划认可(决定投入批量生产)B B认可采购认可(对生产手段的投资认可)D D认可零件生产和供应认可(为零批量)BMG 产品工程性能认可EM 进行首批样件检验的首批样件，首批样件检验也称首批样件认可。EMPB EMPB首批样件检验报告(供货商对

2、其样件检验的文件)2TP 两日生产(供货厂的批量预生产，用来验证批量能力)PVS 生产试制批量0S 零批量(在批量生产条件下的总演习)SF 批量认可(对批量生产的产品认可)EPF (批量供货)计划认可KAF 集团路试验收(质量方面的批量认可) SOP 生产启动(批量生产启动)ME 市场导入(提供给销售商)CAD 计算机辅助设计COP 沿用件(与先前车型通用的零件)CKD 全部拆散SKD 部分拆散HT 自制件KT 外购件(外部供货厂生产的零件)KD 售后服务OTS 用批量生产的模具生产的零件TE 技术开发部PE (合资厂中的)产品工程部TL 技术供货条件TS 产品零件表ZP 检查点ZSB 总成A

3、EKO (产品)改动的控制组织转载请注明出自六西格玛品质论坛 常用英文缩写对照表英文缩写英文对照中文对照ETEngineering Trial工程试制PTProduction Trial生产试制ISIRInitial Sample Inspection Report初始样件测试报告QFDQuality Faction Deployment品质机能展开FMEAFailure Mode and Effect Analysis潜在缺陷模式及后果分析FTAFault Tree Analysis故障树分析ES TESTEngineering Specification Test工程测试QDCQualit

4、y Delivery Cost质量交货成本VDRVender Design Review外包零件设计审查VESVehicle Evaluation System整车评价NDSNissan Design Standard日产设计标准NESNissan Examinational Standard日产试验标准QICQuality Information Center质量信息中心MQICMarket Quality Information Center市场质量信息中心L-PESLocal parts-Prepared Evaluation System零件准备评价系统N-PESNissan new

5、model-Prepared Evaluation System日产新车型准备评价系统U-PESUnit Prepared Evaluation System新引擎(零件)准备评价系统EESEngine Evaluation System引擎评价系统EES-GEngine Evaluation System G(General)整体引擎评价系统EES-SEngine Evaluation System S(Static)静态引擎评价系统SNPStandard Number of Package标准数量包装CKDCompleted Knock Down进口件TQMTotal Quality Ma

6、nagement全面质量管理SOPStart Of Production开始量产OSM- Outside of MaterialOTC Over The Counter 非处方药，可在柜台上卖的药PA Program Approvalpallet n. 托盘Passenger Vehicle 乘用车PAT- Program Attributes Team 产品属性小组PDL Product Design LetterPH Proportions&HardpointsPIPC- Percentage of Indexes with Process Capability 能力指数百分比PIST-

7、Percentage of Inspection points Satisfying Tolerance 检测点满意工差百分比PMT- Program Moudle Team 产品模块小组PO Purchase OrderPPAP- Production Part Approval Process 生产件批准程序PPSR Production Preparation Status ReportPQA Process Quality AssurancePR Program ReadinessPre-Launch 试生产price-driven costing 价格引导成本Production P

8、reparation-Final Nissan - PT2/Renault - PPProduction Preparation-Initial Nissan - PT1/Renault - PPP3Production Trial Run 试生产Prototype 样件QFD Quality Funtion Deploy质量功能展开QFTT Quality Functional Task TeamQR- Quality Reject 质量拒收QS Quality StandardRAN Release Authorisation Numberreverse 倒车档RFQ Request Fo

9、r Quotation询价RKD Reverse Knock DownRLQ Receiving Lot QuantityROC Rate of ClimbROI return on investment 报酬率ROP Re-Order PointRTO Required To OperateSAIS Supplier Assessment & Improvement SystemSC Strategic Confirmation/significant CharacteristicsSDS- System/ Design Specifications 系统/设计说明second gear 二

10、档SFMEA System FMEAShipping Date 出货日、Invoice Date 发票日或On Board Date 装船日Side Windshield 侧窗玻璃SJ Strategic IntentSNP Standard Number of Parts1PP- First Phase of Production Prove-Out 第一次试生产3C Customer(顾客导向)、Competition(竞争导向)、Competence（专长导向）4S Sale, Spare part备件, Service, Survey信息反馈5S 整理，整顿，清理，清洁，素养8D- 8

11、 DisciplineABS Anti-lock Braking SystemAIAG 美国汽车联合会ANPQP Alliance New Product Quality ProcedureApportionment 分配APQP Advanced Product Quality PlanBacklite Windshield 后窗玻璃Benchmark Data 样件资料bloodshot adj.充血的, 有血丝的BMW Bavarian Motor WorksSOW- state of work 工作申明SPC Statistical Process ControlSQA Supplie

12、r Quality AssuranceSREA- Supplier Request for Engineering Approval 供应商工程设计更改申请ST Surface TranferSTRS Supplier Test Report SystemSubcontractor 分承包商Sunroof Windshield 天窗玻璃SUV Sports Utility VehicleTAG Test Aptitude GraphiqueTCO Total Cost of Ownership 总持有成本TCRA Total Cost Reduction ActivityTGR Things

13、Gone RightTGW Things Gone WorstTM Techinical ManualTPM Total Preventive MaintenanceTTO-Tool Try Out 工装验证UOM Unit Of MeasureVES Vehicle uation SystemVO- Vehicle Operation 主机厂VPP- Vehicle Program Plan 整车项目计划VQA Vehicle Quality AssuranceVTTO- Vendor Tool Try-Out 供应商工装验证WERS- World Wide Engineering Rele

14、ase SystemWVTA Whole Vehicle Type Approval凹坑 concave车床 lathe抽查试验spot check test出厂试验delivery test次品defective product调幅amplitude modulation (AM)调频 Frequency Modulation断差 offset对讲机 interphone法平面normal plane翻车rollover返工 re-doing防滑地板 no-skid floor仿真emulation副作用side effect改装厂 refitting factory隔热板heat shie

15、ld后围侧板 rear wall side cover划痕 scratchC.P.M Certified Purchasing manger 认证采购经理人制度CB- Confirmation Build 确认样车制造CC- Change CutOff 设计变更冻结CCSC- critical/significant characteristicCCR Concern & Countermeasure RequestCCT Cross Company TeamCharacteristics Matrix 特性矩阵图COD Cash on Delivery 货到付现预付货款(T/T in adv

16、ance)CP1- Confirmation Prototype 1st 第一次确认样车CP2- Confirmation Prototype 2nd 第二次确认样车Cpk 过程能力指数Cpk=Zmin/3CPO Complementary Parts OrderCraftsmanship 精致工艺Cross-functional teams跨功能小组CUV Car-Based Ultility VehicleD1：信息收集；8DD2：建立8D小组；D3：制定临时的围堵行动措施，避免不良品流出；D4：定义和证实根本原因，避免再发；D5：根据基本原因制定永久措施；D6：执行和确认永久措施；D7：

17、预防再发，实施永久措施；D8：认可团队和个人的贡献。DCC Design Change ControlDFA- Design For Assembly 面向装配的设计DOE Design Of Examination试验设计DQES Delivery Quality uation SystemDTL Direct To LineDVP&R Design Validate Plan&Report设计验证计划报告EDI electronic data interchange 电子数据交换entire adj. 全部的, 完整的, 整个ERP Enterprise Resource Planning

18、ES Engineering Specification工程规格ESI Early Supplier Involvement 供应商先期参与Ex-Work（工厂交货）、FOB（船上交货）、FAS（船边交货）或CIF（运保费在内交货）FEU- Field uation Units 用户市场实际体验与评估first gear 一档Flow Chart 流程图FMEA Failure Mode and Effects Analysisfour-wheel drive 四轮驱动FRG- Ford Reliability Guideline 福特可靠性指导Front Windshield 前挡风玻璃Te

19、mpered glass 钢化玻璃front-wheel drive 前轮驱动FSS- Full service supplier 全服务供应商FTA Fault Tree AnalysisGD&T- Geometric Dimensioning & Tolerancing 标准公差GR&R Guage Repeatability & reproducibility量具的重复性和再现性grief-stricken adj. 极度忧伤的heavy rain 大雨high wind n.疾风HTFB- Hard Tooling Functional Build 工装集成调试与验证IPO Indiv

20、idual Parts OrderISIR Initial Sample Inspection ReportJIT Just In TimeKD- knocked down/ Semi Knock Down(SKD) /Completely Knock Down(CKD)KO Kick-offLaminated glass 夹层玻璃LPLean Production 精益生产LR Launch ReadinessLS Launch SupportLVPM Local Vendor Packaging MethodMPV Multi-Purpose Vehicle 多用途汽车MRD Materi

21、al Required Date假人dummy间隙 interstice节点pitch point油漆起结皮现象skinning扭矩torque汽车总布置草图sketch for automobile layout汽车总装配图automobile assembly drawing汽油供给管gasoline feed pipe汽油箱gasoline tank( petrol tank)前围角板 front wall angle cover轻型客车light bus曲轴crankshaft三类底盘 three type chassis上模upper die甚高频very high frequenc

22、y (VHF)下模bottom die(counter die)消声器silencer选料上乘、做工精细be superior in material and excellent in workmanship仪表板 dash board油门throttle褶皱 crimple整车运输transportation of truck-load总装 final assembly阻流板step,reflectro,baffle最大扭矩转速speed at maximum torque左对齐left justify报废scrapping皮纹 grainOTS OFF TOOL SAMPLE 用批量生产的

23、工模器具制造出的样件PVS Produktions Versuchs Serie 批量试生产TMA Trial Manufacturing Agreement2TP 两日试生产，主要是验证供应商的批量供货能力OS 零批量，是批量生产前的总演习，批产的全面验证SOP Standard Operation 即批量生产 Start-Of-Production Standard Operating Procedure 标准操作程序QSV Qualitaes-Sicherungs-Vereinbarung 质量保证协议BMG Bau-Muster-Genehmigung 产品工程样件性能检验认可Null

24、 series 零批量QSR 质量体系要求Bias 偏差DB Durability Build 样车阶段lead time n.订货至交货的时间sink mark 缩痕LRR launch readiness reviewMRO Maintenance, Repair, and OperationMTP- Make to print supplier 照图加工供应商N/A- Not ApplicableNCDR Non-Conforming Delivery ReportNCMAR Non-Conforming Material Action ReportNDA Non Disclosure

25、Agreement 保密协定NDS Nissan Design SpecificationNML Nissan Motor LtdNVH- System Noise, Vibration & Harshness 系统噪音,振动及粗糙性onetime adj.过去的，从前的Front bumper 前保险杠Rear bumper 后保险杠Radiator grille 格栅Headlamp 前大灯Tail lamp-lift gate 尾灯-行李箱盖上Tail lamp-quarter 尾灯-后侧围上Front door trim panel 前门内饰板Rear door trim panel

26、后门内饰板Interior release handle bezel 内开手把手框Power controls bezel 电动车窗开关框Window interior capping 窗框饰条Exterior mirror 外后视镜Body side moulding 防擦条Cowl grille 通风格栅Roof molding 车顶装饰条Lift gate molding 牌照板支架Lift gate handle 行李箱盖拉手Weather strip_door openings 门框胶条Weather strip_liftgate 行李箱胶条A Pillar Trim A柱B Pil

27、lar Trim upper B柱上B Pillar Trim lower B柱下Front scuff Plate 前门槛条Rear scuff plate 后门槛条Back panel trim lower 行李箱门槛条Garnish trim-Quarter windowCowl trim panel A柱下Lift gate upper trim 尾门内饰板上Lift gate side trim 尾门内饰板中Lift gate lower trim 尾门内饰板下IPDefroster panel 除霜盖板Console 中控台Steering column cover 方向机柱上下盖

28、板Cluster 组合仪表Carpet 前地毯Trunk carpet 后地毯Front seat 前座椅2nd row seat 第二排座椅burr(金属) flash(塑件)毛边gap 间隙defective products 不良品finished products 成品disposed products 处理品band-aid 创可贴scratch 刮伤dents 压痕缩水 Shrinkage缩水 Sink Mark顶白 Stress MarkYC (Potential Critical Characteristic) 潜在关键特性YS (Potential Significant C

29、haracteristic) 潜在重要特性Restriction of Hazardous Substances 简称RoHS SGS, BV, TUV, Intertek, ETC BV-Bureau Veritas 法国国际检验局首检 First article inspection自检 Self-inspection全检 100% inspection巡检 process audit开箱检验 out of box audit出货检验 out-going inspection进货检验 in-coming inspection例行检验 Routine checking确认检验 Confirm

30、ing全尺寸检验 full dimension inspection可靠性试验 Reliability test在线检验 on-line inspection线下检验 off-line inspection制造业英文词汇总经理办公室General managers office模具部Tooling department项目部Project department品质部Quality department计划部 Plan department制造部Manufacture departmentKeypad产品部Keypad departmentIMD 产品部 IMD department五金部 Me

31、tal stamping department设计科 Design section冲压车间 Stamping workshop电镀车间 Plating workshop物控科 Production material control section计划科 Plan section仓务科 Warehouse section商务科 Business section品质规划科 quality plan sectionIQC科 IQC sectionIPQC科 IPQC sectionOQC科 OQC section检测中心 measurement center项目规划科 Project plan se

32、ction项目XX科 Project section XX试模科 Mold test section成本科 Cost section设备科 Facility section采购科 Purchase section综合办 General affairs office编程科 Programming section模具工程科 Tooling engineering section模具装配车间Mold assembly workshop文控中心 Document control center (DCC)注塑车间Injection workshop喷涂车间 Spray painting workshop

33、装配车间Assembly workshop总经理General manager (GM)经理managerXX部门经理Manager of XX department原料库 Raw material warehouse半成品库 Semi-finished product warehouse成品库 Finished product warehouse科长 section chief主任 chief部门主管 department head主管, 线长supervisor组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant职员staf

34、f二、产品超声波焊接ultrasonic welding塑胶件 Plastic parts塑材 Raw parts喷涂件 Painted parts装配件 Assembly parts零件 Component原料 Raw material油漆 Paint稀释剂 Thinner油墨 Ink物料编号part number三、模具注塑模具injection mold冲压模具Stamping tool模架mold base定模座板Fixed clamp plateA板A plateB板B plate支承板 support plate方铁 spacer plate回位销 Return pin导柱 Gui

35、de pin动模座板Moving clamp plate顶针ejector pin单腔模具single cavity mold多腔模具multi-cavity mold浇口gate合模力clamping force锁模力locking force开裂crack循环时间cycle time老化aging螺杆screw镶件 Insert主流道 sprue分流道runner浇口gate直浇口 direct gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate浇口套sprue bush流道板runner plate排气槽vent分型线(面)partin

36、g line定模Fixed mold动模movable mold型腔cavity凹模cavity plate,凸模core plate斜销angle pin滑块slide拉料杆sprue puller定位环locating ring脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mold熔合纹weld line三板式模具three plate mold脱模ejection脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure保压时间hold

37、ing time闭模时间closing time电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine平面磨床Surface grinding machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller倒角chamfer键Key键槽keyway间距pitch快速成型模Rapid prototype tool (RPT)四、品管SPC statistic process control品质保证Quality

38、Assurance(QA)品质控制Quality control(QC)来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration环境试验Environmental test光泽gloss拉伸强度tensile strength盐雾实验salt spray test翘曲warp比重specific gravity疲劳fatigue撕裂强度tear strength缩痕sink mark耐久性durability抽样sampling样品数量sample sizeAQL Acceptable Qual

39、ity level批量lot size抽样计划sampling plan抗张强度 Tensile Strength抗折强度 Flexural Strength硬度 Rigidity色差 Color Difference涂镀层厚度 Coating Thickness导电性能 Electric Conductivity粘度 viscosity附着力 adhesion耐磨 Abrasion resistance尺寸 Dimension(喷涂)外观问题 Cosmetic issue不合格品 Non-conforming product限度样板 Limit sample五、生产注塑机injection

40、machine冲床Punch machine嵌件注塑 Insert molding双色注塑 Double injection molding薄壁注塑 Thin wall molding膜内注塑 IMD molding ( In-mold decoration)移印 Tampo printing丝印 Silk screen printing热熔 Heat staking超声熔接 Ultrasonic welding (USW)尼龙nylon黄铜 brass青铜 bronze紫(纯)铜 copper料斗hopper麻点pit配料compounding涂层coating飞边flash缺料 Short

41、 mold烧焦 Burn mark缩水 Sink mark气泡 Bubbles破裂 Crack熔合线 Welding line流痕 Flow mark银条 Silver streak黑条 Black streak表面光泽不良 Lusterless表面剥离 Pelling翘曲变形 Deformation脏圬 Stain mark油污 Oil mark蓝黑点 Blue-black mark顶白 Pin mark拉伤 Scratch限度样品 Limit sample最佳样品 Golden sample预热preheating再生料recycle material机械手 Robot机器人 Servo

42、robot试生产 Trial run; Pilot run (PR)量产 mass production切料头 Degate产能 Capacity能力 Capability参数 Parameter二次加工 Secondary process六.物控保质期shelf lifeABC分类法ABC Classification装配Assembly平均库存Average Inventory批号Batch Number批量生产Mass Production提货单Bill of Lading物料清单Bill of Material采购员Buyer检查点Check Point有效日期Date Availab

43、le修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required需求管理Demand Management需求Demand工程变更生效日期Engineering Change Effect Date呆滞材料分析Excess Material Analysis完全跟踪Full Pegging在制品库存In Process Inventory投

44、入/产出控制Input/ Output Control检验标识Inspection ID库存周转率Inventory Carry Rate准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time负荷Loading仓位代码Location Code仓位状况Location Status批量标识Lot ID批量编号Lot Number批量Lot Size机器能力Machine Capacity机器加载Machine Loading制造周期时间Manufacturing Cycle Time制造

45、资源计划Manufacturing Resource Planning (MRP II)物料成本Material Cost物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning (MRP)现有库存量On-hand Balance订单输入Order Entry零件批次Part Lot零件编号Part Number (P/N)零件Part领料单Picking List领料/提货Picking产品控制Product Control产品线Production Line采购订单跟踪Purchase Order Tra

46、cking需求量Quantity Demand毛需求量Quantity Gross安全库存量Safety Stock在制品Work in Process零库存Zero Inventories七.QS-9000中的术语APQP Advanced Product Quality,所得税汇算清缴; Planning and Control Plan,产品质量先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析MSA,税审; M

47、easure System Analysis,测量系统分析SPC Statistical Process Control,统计过程控制审核 Audit能力 Capability能力指数 Capability Indices控制计划 Control Plans纠正措施 Corrective Action文件 Documentation作业指导书 Standard operation procedure(SOP); Work instruction不合格品 Nonconformance不合格 Nonconformity每百万零件不合格数 Defective Parts Per Million, D

48、PPM预防措施 Preventive Action程序Procedures过程流程图 Process Flow Diagram, Process Flow Chart质量手册Quality Manual质量计划 Quality Plan质量策划 Quality Planning质量记录Quality Records原始数据Raw Data反应计划Reaction Plan返修Repair返工Rework现场Site分承包方Subcontractors产品product质量quality质量要求quality requirement顾客满意customer satisfaction质量管理体系q

49、uality management system质量方针quality policy质量目标quality objective质量管理quality management质量控制quality control质量保证quality assurance组织organization顾客customer供方supplier过程process服务service设计与开发design and development:特性characteristic可追溯性trace ability合格conformity缺陷defect纠正correction让步concession放行release报废scrap规范

50、specification检验inspection试验test验证verification评审review测量measurement普通原因Common Cause均值Mean极差Range稳定性Stability计量型数据Variables Data变差Variation重复性Repeatability再现性Reproducibility稳定性Stability线性Linearity分辨率Resolution过程更改Process change质量功能展开QFD外观项目Appearance Item初始过程能力Preliminary Process Capability材料清单Bill of

51、 Material设计确认Design Validation设计验证Design Verification八.常用缩略词语OEM Original Equipment ManufacturerANOVA 方差分析法 Analysis of VarianceDFMEA 设计失效模式及后果分析 Design Failure Mode and Effects AnalysisDOE 试验设计 Design of ExperimentGR&R 量具的重复性和再现性Gage Repeatability and ReproducibilityPFMEA 过程失效模式及后果分析Process Failure Mode and Effect AnalysisQSR 质量体系要求Quality System RequirementQFD 质量功能