无线配置手册(CT5508%2BAP1142N)

1、无线基本配置手册（ct5508+ap1142n）1、初始化控制器 初始化准备：控制器的console口与电脑的串口连接好，打开超级终端(默认)，给控制器通电，按住电脑的esc键进入配置向导，配置实例为cisco wlc4402的配置，ct5508配置同wlc4402；system will now restart!bootloader (apr 12 2007 - 17:46:14)motorola powerpc processorid=00000000 rev. pvr=80200020 cpu: 833 mhz ccb: 333 mhz ddr: 166 mhz lb

2、c: 41 mhzl1 d-cache 32kb, l1 i-cache 32kb enabled.i2c: readydtt: 1 is 33 cdram: ddr module detected, total size:512mb.512 mb8540 in pci host mode.8540 is the pci arbiter.memory test passflash: flash bank 0: portsize = 2, size = 8 mb in 142 sectors 8 mbl2 cache enabled: 256kbcard id: 1540card revisio

3、n id: 1card cpu id: 1287number of mac addresses: 32number of slots supported: 4serial number: foc1127f04hunknown command id: 0xa5unknown command id: 0xa4unknown command id: 0xa3manufacturers id: 30464board maintenance level: 00number of supported aps: 50in: serialout: serialerr: serial .o88b. d88888

4、8b .d8888. .o88b. .d88b. d8p y8 88 88 yp d8p y8 .8p y8. 8p 88 8bo. 8p 88 88 8b 88 y8b. 8b 88 88 y8b d8 .88. db 8d y8b d8 8b d8 y88p y888888p 8888y y88p y88p model air-wlc4402-50-k9 s/n: foc1127f04hnet: phy device : found intel lxt971a phy at 0x01fec ethernetide: bus 0: ok device 0: model: sti flash

5、7.4.0 firm: 01.25.06 ser#: sti j11b407102084630 type: removable hard disk capacity: 245.0 mb = 0.2 gb (501760 x 512) device 1: not availablebooting primary image.press now for additional boot options.* external console active * boot optionsplease choose an option from below: 1. run primary image (ve

6、rsion ) (active) 2. run backup image (version ) 3. manually update images 4. change active boot image 5. clear configurationplease enter your choice: 5 清除原有的配置detecting hardware . . .re-building configuration filesystemdone.bootloader (apr 12 2007 - 17:46:14)motorola powe

7、rpc processorid=00000000 rev. pvr=80200020 cpu: 833 mhz ccb: 333 mhz ddr: 166 mhz lbc: 41 mhzl1 d-cache 32kb, l1 i-cache 32kb enabled.i2c: readydtt: 1 is 33 cdram: ddr module detected, total size:512mb.512 mb8540 in pci host mode.8540 is the pci arbiter.memory test passflash: flash bank 0: portsize

8、= 2, size = 8 mb in 142 sectors 8 mbl2 cache enabled: 256kbcard id: 1540card revision id: 1card cpu id: 1287number of mac addresses: 32number of slots supported: 4serial number: foc1127f04hunknown command id: 0xa5unknown command id: 0xa4unknown command id: 0xa3manufacturers id: 30464board maintenanc

9、e level: 00number of supported aps: 50in: serialout: serialerr: serial .o88b. d888888b .d8888. .o88b. .d88b. d8p y8 88 88 yp d8p y8 .8p y8. 8p 88 8bo. 8p 88 88 8b 88 y8b. 8b 88 88 y8b d8 .88. db 8d y8b d8 8b d8 y88p y888888p 8888y y88p y88p model air-wlc4402-50-k9 s/n: foc1127f04hnet: phy device : f

10、ound intel lxt971a phy at 0x01fec ethernetide: bus 0: ok device 0: model: sti flash 7.4.0 firm: 01.25.06 ser#: sti j11b407102084630 type: removable hard disk capacity: 245.0 mb = 0.2 gb (501760 x 512) device 1: not availablebooting primary image.press now for additional boot options.detecting hardwa

11、re . . .generating secure shell dsa host key .generating secure shell rsa host key .generating secure shell version 1.5 rsa host key .cisco is a trademark of cisco systems, inc.software copyright cisco systems, inc. all rights reserved.cisco aireos version initializing os services: okinitia

12、lizing serial services: okinitializing internal interfaces: okinitializing network services: okstarting arp services: okstarting trap manager: okstarting network interface management services: okstarting system services: okstarting fast path hardware acceleration: okstarting switching services: okst

13、arting qos services: okstarting fips features: not enabledstarting policy manager: okstarting data transport link layer: okstarting access control list services: okstarting system interfaces: okstarting client troubleshooting service: okstarting management frame protection: okstarting lwapp: okstart

14、ing crypto accelerators: none presentstarting certificate database: okstarting vpn services: okstarting security services: okstarting policy manager: okstarting authentication engine: okstarting mobility management: okstarting virtual ap services: okstarting airewave director: okstarting network tim

15、e services: okstarting cisco discovery protocol: okstarting broadcast services: okstarting logging services: okstarting dhcp server: okstarting ids signature manager: okstarting rfid tag tracking: okstarting power supply and fan status monitoring service: okstarting tsm: okstarting locp: ok starting

16、 cids services: okstarting ethernet-over-ip: okstarting management services: web server: ok cli: ok secure web: web authentication certificate not found (error).(cisco controller) welcome to the cisco wizard configuration tooluse the - character to backupsystem name cisco_68:9b:e3: cisco_wlc_master

17、设置无线控制器的系统命名enter administrative user name (24 characters max): admin 设置无线控制器的管理员enter administrative password (24 characters max): * 设置无线控制器的管理员密码re-enter administrative password : * 确认设置无线控制器管理员密码service interface ip address configuration nonedhcp: none 是否开启web管理口的dhcp服务service interface ip addres

18、s: 设置web管理口的管理地址service interface netmask: 设置web管理口的管理地址的掩码enable link aggregation (lag) yesno: no 是否开启链路汇聚功能management interface ip address: 设置无线控制器的管理地址management interface netmask: 设置无线控制器的管理地址的掩码management interface default router: 1 设置无

19、线控制器的管理端口的默认网关management interface vlan identifier (0 = untagged): 2 设置无线网络所属的vlanmanagement interface port num 1 to 2: 1 设置管理端口为端口1或端口2management interface dhcp server ip address: 1 设置dhcp服务器地址ap transport mode layer2layer3: layer3 设置传输模式为3层传输ap manager interface ip address: 设置ap

20、的管理接口地址ap-manager is on management subnet, using same valuesap manager interface dhcp server (): 设置ap的管理接口的dhcp服务器地址virtual gateway ip address: 设置虚拟的网关地址mobility/rf group name: group1 设置所属的分组enable symmetric mobility tunneling yesno: yes 是否启用移动传输功能network name (ssid): cimc 设置无线网络的s

21、sidallow static ip addresses yesno: yes 是否接受静态ip地址configure a radius server now? yesno: no 是否马上设置radius服务warning! the default wlan security policy requires a radius server.please see documentation for more details.enter country code list (enter help for a list of countries) us: cn 输入所属的地区enable 802.

22、11b network yesno: yes 是否启用802.11b的网络enable 802.11a network yesno: yes 是否启用802.11a的网络enable 802.11g network yesno: yes 是否启用802.11g的网络enable auto-rf yesno: yes 是否启用自动射频configuration saved!resetting system with new configuration.configuration saved!resetting system with new configuration.*以下为查看ct5508相

23、关配置信息 (cisco controller) enter user name (or recover-config this one-time only to reset configuration to factory defaults)user: adminpassword:*(cisco controller) (cisco controller) show tech-support 查看无线控制器当前状态-show boot-(cisco controller) show bootprimary boot image. (default) (active) ba

24、ckup boot image. -show time-(cisco controller) show time time. fri jun 7 16:00:43 2013timezone delta. 0:0timezone location. (gmt +8:00) hongkong, bejing, chongquingntp servers ntp polling interval. 86400 index ntp key index ntp server ntp msg auth status- -show inventory-(cisco controller)

25、show inventory burned-in mac address. 30:e4:db:1b:ea:c0power supply 1. present, okpower supply 2. absentmaximum number of aps supported. 50name: chassis , descr: cisco 5500 series wireless lan controllerpid: air-ct5508-k9, vid: v01, sn: fcw1536l0en-show udi-(cisco controller) show udi name: chassis

26、, descr: cisco 5500 series wireless lan controllerpid: air-ct5508-k9, vid: v01, sn: fcw1536l0en-show sysinfo-(cisco controller) show sysinfo manufacturers name. cisco systems inc.product name. cisco controllerproduct version. bootloader version. 1.0.1field recovery image version. f

27、irmware version. fpga 1.3, env 1.6, usb console 1.27build type. data + wpssystem name. 2po2a2-oa-ws-ct5508-ssystem location. system contact. system objectid. ..1069ip address. 50last reset. power on resetsystem up time. 224 days 3 hrs 31 mins 1 secssystem timezone location. (g

28、mt +8:00) hongkong, bejing, chongquingcurrent boot license level. basecurrent boot license type. permanentnext boot license level. basenext boot license type. permanentconfigured country. cn - china-more- or (q)uitoperating environment. commercial (0 to 40 c)internal temp alarm limits. 0 to 65 cinte

29、rnal temperature. +35 cexternal temperature. +21 cfan status. okstate of 802.11b network. enabledstate of 802.11a network. enablednumber of wlans. 3number of active clients. 217burned-in mac address. 30:e4:db:1b:ea:c0power supply 1. present, okpower supply 2. absentmaximum number of aps supported. 5

30、0-show interface -(cisco controller) show interface summary 查看所有接口信息interface name port vlan id ip address type ap mgr guest- - - - - - -management lag 52 50 static yes no service-port n/a n/a static no no virtual n/a n/a static no no vlan 128 lag 128 50 dynamic no

31、 no vlan 130 lag 130 50 dynamic no no vlan 132 lag 132 50 dynamic no no vlan126 lag 126 50 dynamic no no vlan134 lag 134 50 dynamic no no (cisco controller) show interface detailed management 查看管理接口信息interface name. managementmac address. 30:e4:db:1b:ea:cfip a

32、ddress. 50ip netmask. ip gateway. 54external nat ip state. disabledexternal nat ip address. vlan. 52 quarantine-vlan. 0active physical port. lag (13)primary physical port. lag (13)backup physical port. unconfiguredprimary dhcp server. 54secondary dhcp s

33、erver. 53dhcp option 82. disabledacl. unconfiguredap manager. yesguest interface. nol2 multicast. disabled(cisco controller) (cisco controller) show interface summary incorrect usage. use the ? or key to list commands.(cisco controller) show interface detailed service-port 查看服务接口详细信息interfa

34、ce name. service-portmac address. 30:e4:db:1b:ea:c1ip address. ip netmask. dhcp option 82. disableddhcp protocol. disabledap manager. noguest interface. no(cisco controller) show interface detailed virtual 查看虚接口详细信息interface name. virtualmac address. 30:e4:db:1b:ea:c0ip address.

35、dhcp option 82. disabledvirtual dns host name. disabledap manager. noguest interface. no-show port summary-(cisco controller) show port summary 查看当前所有端口情况 stp admin physical physical link linkpr type stat mode mode status status trap poe sfptype - - - - - - - - - -1 normal forw enable auto 10

36、00 full up enable n/a 1000basesx 2 normal disa enable auto auto down enable n/a not present 3 normal disa enable auto auto down enable n/a not present 4 normal disa enable auto auto down enable n/a not present 5 normal disa enable auto auto down enable n/a not present 6 normal disa enable auto auto

37、down enable n/a not present 7 normal disa enable auto auto down enable n/a not present 8 normal disa enable auto auto down enable n/a not present -show process cpu-(cisco controller) show process cpu 查看当前所有进程的cpu使用情况 name priority cpu use reaper cslstoremanager (240/ 7) 0 ( 0/ 0)% system reset task

38、(240/ 7) 0 ( 0/ 0)% reaperwatcher ( 3/ 96) 0 ( 0/ 0)% i osapireaper ( 10/ 94) 0 ( 0/ 0)% i tempstatus (240/ 7) 0 ( 0/ 0)% i pktdebugsockettask (255/ 1) 0 ( 0/ 0)% license agent (240/ 7) 0 ( 0/ 0)% i emweb (240/ 7) 0 ( 0/ 0)% t 300 webjavatask (240/ 7) 0 ( 0/ 0)% fmchstask (100/ 60) 0 ( 0/ 0)% apstatenginetask (240/ 7) 0 ( 0/ 0)% rrcenginetask (240/ 7) 0 ( 0/ 0)% t 300 spectrumnmsptask (255/ 1) 0 ( 0/ 0)% spectrumdatatask (255/ 1) 0 ( 0/ 0)% w