融合终端配网产品信息模型(无功补偿设备)

信息模块类别,描述,名称,数据类型,字节数,数据格式,单位,取值范围,备注

参数定值,目标功率因数（上限值）,PhPF_Up,float,2,X.XX,,0.80~1.00,

,目标功率因数（下限值）,PhPF_Down,float,2,X.XX,,0.80~1.00,

,电流互感器变比,CT_Ratio,uint,2,XXXX,,1~600,

,温度保护动作限值,Tmp_Lim,uint,1,XX,摄氏度,20~70,

,温度保护回差,Tmp_ReErr,uint,1,XX,K,2~10,

,电流谐波限值,ThdA_Lim,uint,2,XXXX,百分比,20~60,

,一级过电压限值,PTOV_Op_Lim_L1,float,2,XXX.X,V,"共补：400~420

分补：231~241",

,二级过电压限值,PTOV_Op_Lim_L2,float,2,XXX.X,V,"共补：421~460

分补：242~264",

,电压限值回差,Vol_ReErr,float,2,XXX,,2~12,

,低负荷电流闭锁限值,A_LO_Lim,float,1,X.XX,A,0.10~1.00,

,告警屏蔽,Alm_Mask,uint,2,XXXX,,0~FFFH,

,控制模式,Ctrl_Mod,uint,1,XX,,,"01远方控制模式

00表示当地模式"

,过电压门限,PTOV_Lim,float,2,XXX,V,,

,欠电压门限,PTUV_Lim,float,2,XXX,V,,

,动作延时时间,Act_Delay,float,2,XXX,秒,,

,电容1过温度值,Tmp_Lim_Grp1,float,2,XXX,摄氏度,,

,电容2/电抗过温度值,Tmp_Lim_Grp2,float,2,XXX,摄氏度,,

,投入无功门限,PutInVAr_Lim,float,2,XXX.X,kVar,,

,切除无功门限,CutOutVAr_Lim,float,2,XXX.X,kVar,,

,功率因数门限,PhPF_Lim,float,2,X.XXX,,,

,电压谐波门限,HphV_Lim,float,2,XX.X,%,,

,电流谐波门限,HA_Lim,float,2,XX.X,%,,

,无功补偿控制方式,CtrlMode,uint,1,,,,0x01表示终端控制，0x11智能电容器控制

,低负荷电流闭锁限值,StartCur,float,,XX.X,A,0-1.00,

,二级过压限值的比例,OV2_Coeff,float,,XXXX.XX,,,

,一级过压限值的比例,OV1_Coeff,float,,XXXX.XX,,,

,电压限值回差,OV_Rtn,float,,XX,,,

,电流谐波限值,ha_Coeff,float,,XXXX.XX,%,,

,温度保护阀值,temp_Coeff,float,,XXXX.XX,℃,,

,温度保护回差,temp_Rtn,float,,XXXX.XX,℃,,

,告警屏蔽字,alarm_msk,uint,2,,,,

,时段数目,seg_num,uint,1,,,,

,时段1功率因数上限值,seg1_UpperPF,float,,XX.XXX,,0-1.000,

,时段1功率因数下限值,seg1_lowerPF,float,,XX.XXX,,0-1.000,

,时段1使能标志：0禁止1为使能,seg1_flag,bool,,,,,

,时段1开始时间:0x0830为8:30,seg1_starttime,uint,2,,,,

,时段2功率因数上限值,seg2_UpperPF,float,,XX.XXX,,0-1.000,

,时段2功率因数下限值,seg2_lowerPF,float,,XX.XXX,,0-1.000,

,时段2使能标志：0禁止1为使能,seg2_flag,bool,,,,,

,时段2开始时间:0x0830为8:30,seg2_starttime,uint,2,,,,

,时段3功率因数上限值,seg3_UpperPF,float,,XX.XXX,,0-1.000,

,时段3功率因数下限值,seg3_lowerPF,float,,XX.XXX,,0-1.000,

,时段3使能标志：0禁止1为使能,seg3_flag,bool,,,,,

,时段3开始时间:0x0830为8:30,seg3_starttime,uint,2,,,,

,时段4功率因数上限值,seg4_UpperPF,float,,XX.XXX,,0-1.000,

,时段4功率因数下限值,seg4_lowerPF,float,,XX.XXX,,0-1.000,

,时段4使能标志：0禁止1为使能,seg4_flag,bool,,,,,

,时段4开始时间:0x0830为8:30,seg4_starttime,uint,2,,,,

,时段5功率因数上限值,seg5_UpperPF,float,,XX.XXX,,0-1.000,

,时段5功率因数下限值,seg5_lowerPF,float,,XX.XXX,,0-1.000,

,时段5使能标志：0禁止1为使能,seg5_flag,bool,,,,,

,时段5开始时间:0x0830为8:30,seg5_starttime,uint,2,,,,

,时段6功率因数上限值,seg6_UpperPF,float,,XX.XXX,,0-1.000,

,时段6功率因数下限值,seg6_lowerPF,float,,XX.XXX,,0-1.000,

,时段6使能标志：0禁止1为使能,seg6_flag,bool,,,,,

,时段6开始时间:0x0830为8:30,seg6_starttime,uint,2,,,,

,时段7功率因数上限值,seg7_UpperPF,float,,XX.XXX,,0-1.000,

,时段7功率因数下限值,seg7_lowerPF,float,,XX.XXX,,0-1.000,

,时段7使能标志：0禁止1为使能,seg7_flag,bool,,,,,

,时段7开始时间:0x0830为8:30,seg7_starttime,uint,2,,,,

,时段8功率因数上限值,seg8_UpperPF,float,,XX.XXX,,0-1.000,

,时段8功率因数下限值,seg8_lowerPF,float,,XX.XXX,,0-1.000,

,时段8使能标志：0禁止1为使能,seg8_flag,bool,,,,,

,时段8开始时间:0x0830为8:30,seg8_starttime,uint,2,,,,

,全切有效标志：0禁止1为使能,allcut_flag,bool,,,,,

,全切开始时间,allcut_starttime,,,,,,

,全切结束时间,allcut_endtime,,,,,,

,装置口令1,Dev_Password_1,string,,,,,

,装置口令2,Dev_Password_2,string,,,,,

,装置口令3,Dev_Password_3,string,,,,,

,装置口令4,Dev_Password_4,string,,,,,

,电压缺相门限（参变量）,Voltage_Phase_Loss_Threshold,,2,Xxx.x,V,,

,电压保护上限（A相电压越下限）,Voltage_Protection_Upper,,2,Xxx.x,V,,

,电压保护下限,Voltage_Protection_Lower,,2,Xxx.x,V,,

,投入电压闸值,Input_Voltage_Threshold,,2,Xxx.x,V,,

,切除电压闸值,Cutoff_Voltage_Threshold,,2,Xxx.x,V,,

,电压谐波闸值,Voltage_Harmonic_Threshold,,2,Xx。xx,%,,

,电流谐波闸值,Current_Harmonic_Threshold,,2,Xx。xx,%,"1.00%~

90.00%",

,目标功率因数,PhPF_Goal,,2,X．xxx,,0.100-1.000,

,投入门限,Entrance_Threshold,,2,XXXX,KVar,0-100.0kvar,

,切除门限,Resection_Threshold,,2,XXXX,KVar,0-100.0kvar,

,过补系数,OverCompFact,,2,X.．X,,0.5-2,

,投切延时,SwDl,,2,XXX,S,0-600s,

,切投延时,CtDl,,2,xxx,s,0-600s,

,组间延时,GrDl,,2,XXX,S,0-600s,

,保护延时,ProDl,,2,xxx,s,0-600s,

,共补路数,Gb_Roads_Num,,2,x,,0-4,

,分补路数,Fb_Roads_Num,,2,x,,0-12,

,第01路电容容量,Cap_Load_R1,,2,XXX．X,Kvar,0-600,

,第02路电容容量,Cap_Load_R2,,2,XXX．X,Kvar,0-600,

,第03路电容容量,Cap_Load_R3,,2,XXX．X,Kvar,0-600,

,第04路电容容量,Cap_Load_R4,,2,XXX．X,Kvar,0-600,

,第05路电容容量,Cap_Load_R5,,2,XXX．X,Kvar,0-600,

,第06路电容容量,Cap_Load_R6,,2,XXX．X,Kvar,0-600,

,第07路电容容量,Cap_Load_R7,,2,XXX．X,Kvar,0-600,

,第08路电容容量,Cap_Load_R8,,2