套管头安装程序动画教学课件

2640mm2600mm36″钻头一开.2640mm2600mm36″钻头一开.136″钻头一开完毕.36″钻头一开完毕.2提36″钻头.提36″钻头.3下30″导管.下30″导管.4固30″导管.固30″导管.5固30″导管完毕.固30″导管完毕.6割30″导管.割30″导管.7安装底座，把30″导管焊接在底座上.安装底座，把30″导管焊接在底座上.826″钻头二开.26″钻头二开.9310m26″钻头二开完毕.310m26″钻头二开完毕.10310m提26″钻头.310m提26″钻头.11310m下20″套管.310m下20″套管.12310m下20″套管完毕.310m下20″套管完毕.13310m固20″套管.310m固20″套管.14310m固20″套管完毕.310m固20″套管完毕.15310m割20″套管.310m割20″套管.16310m安装调节底座及表层套管头，用反卡瓦固定20″套管.310m安装调节底座及表层套管头，用反卡瓦固定20″套管.17310m注密封脂，试压（3000PSI保压15分钟）.310m注密封脂，试压（3000PSI保压15分钟）.18310m安装升高短节.310m安装升高短节.19310m安装升高短节完毕.310m安装升高短节完毕.20310m安装20-3/4″钻井四通.310m安装20-3/4″钻井四通.21310m安装20-3/4″钻井四通完毕.310m安装20-3/4″钻井四通完毕.22310m安装20-3/4″双闸板防喷器.310m安装20-3/4″双闸板防喷器.23310m安装20-3/4″双闸板防喷器完毕.310m安装20-3/4″双闸板防喷器完毕.24310m安装20-3/4″万能防喷器.310m安装20-3/4″万能防喷器.25310m安装20-3/4″万能防喷器完毕.310m安装20-3/4″万能防喷器完毕.26310m下21-1/4″试压塞.310m下21-1/4″试压塞.27310m下21-1/4″试压塞到表层套管四通内.310m下21-1/4″试压塞到表层套管四通内.28310m防喷器试压（3000PSI保压15分钟）.310m防喷器试压（3000PSI保压15分钟）.29310m取出21-1/4″试压塞.310m取出21-1/4″试压塞.30310m下21-1/4″防磨套.310m下21-1/4″防磨套.31310m下21-1/4″防磨套到表层套管四通内.310m下21-1/4″防磨套到表层套管四通内.32310m17-1/2″钻头三开.310m17-1/2″钻头三开.33310m17-1/2″钻头三开.310m17-1/2″钻头三开.34310m17-1/2″钻头三开完毕.310m17-1/2″钻头三开完毕.35310m提17-1/2″钻头.310m提17-1/2″钻头.36310m下钻杆提21-1/4″防磨套.310m下钻杆提21-1/4″防磨套.37310m提出21-1/4″防磨套.310m提出21-1/4″防磨套.38310m下13-3/8″套管.310m下13-3/8″套管.39310m下13-3/8″套管完毕.310m下13-3/8″套管完毕.40310m拆升高短节底部螺栓，上提防喷器组.310m拆升高短节底部螺栓，上提防喷器组.41310m安装13-3/8″卡瓦式套管悬挂器及密封总成.310m安装13-3/8″卡瓦式套管悬挂器及密封总成.42310m安装13-3/8″卡瓦式套管悬挂器及密封总成完毕.310m安装13-3/8″卡瓦式套管悬挂器及密封总成完毕.43310m下移防喷器组，装升高短节底部螺栓.310m下移防喷器组，装升高短节底部螺栓.44310m在表层套管头侧翼4-1/16″法兰上连接泥浆循环管线.310m在表层套管头侧翼4-1/16″法兰上连接泥浆循环管线45310m固13-3/8″套管.310m固13-3/8″套管.46310m提升高短节、防喷器组.310m提升高短节、防喷器组.47310m拆升高短节、防喷器组.310m拆升高短节、防喷器组.48310m割13-3/8″套管.310m割13-3/8″套管.49装中层套管头.装中层套管头.50在中层套管头下法兰注密封脂，试压（10000PSI保压15分钟）.在中层套管头下法兰注密封脂，试压（10000PSI保压15分51装13-5/8″15000PSIX13-5/8″10000PSI转换法兰.装13-5/8″15000PSIX13-5/8″100052装13-5/8″10000PSI钻井四通、防喷器组.装13-5/8″10000PSI钻井四通、防喷器组.53下13-5/8″试压塞.下13-5/8″试压塞.54下13-5/8″试压塞到中层套管四通内.下13-5/8″试压塞到中层套管四通内.55防喷器试压（10000PSI保压15分钟）.防喷器试压（10000PSI保压15分钟）.56取出13-5/8″试压塞.取出13-5/8″试压塞.57下13-5/8″防磨套.下13-5/8″防磨套.58下13-5/8″防磨套到中层套管四通内.下13-5/8″防磨套到中层套管四通内.5912-1/2″钻头四开.12-1/2″钻头四开.6012-1/2″钻头四开完毕.12-1/2″钻头四开完毕.61提12-1/2″钻头.提12-1/2″钻头.62下钻杆提13-5/8″防磨套.下钻杆提13-5/8″防磨套.63提出13-5/8″防磨套.提出13-5/8″防磨套.64下9-5/8″套管.下9-5/8″套管.65下9-5/8″套管完毕.下9-5/8″套管完毕.66在9-5/8″套管端部安装双公短节和9-5/8″心轴式套管悬挂器.在9-5/8″套管端部安装双公短节和9-5/8″心轴式套管悬679-5/8″心轴式套管悬挂器座挂到中层套管四通内.9-5/8″心轴式套管悬挂器座挂到中层套管四通内.68用顶丝固定9-5/8″心轴式套管悬挂器.用顶丝固定9-5/8″心轴式套管悬挂器.69在中层套管头侧翼3-1/16″法兰上连接泥浆循环管线.在中层套管头侧翼3-1/16″法兰上连接泥浆循环管线.70固9-5/8″套管.固9-5/8″套管.71拆转换法兰、钻井四通、防喷器组.拆转换法兰、钻井四通、防喷器组.72装13-5/8″15000PSIX13-5/8″15000PSI作业法兰.装13-5/8″15000PSIX13-5/8″15073装13-5/8″15000PSI钻井四通、防喷器组.装13-5/8″15000PSI钻井四通、防喷器组.74下9-5/8″试压塞.下9-5/8″试压塞.75下9-5/8″试压塞到作业法兰内.下9-5/8″试压塞到作业法兰内.76防喷器试压（15000PSI保压15分钟）.防喷器试压（15000PSI保压15分钟）.77提出9-5/8″试压塞.提出9-5/8″试压塞.78下9-5/8″防磨套.下9-5/8″防磨套.79下9-5/8″防磨套到作业法兰内.下9-5/8″防磨套到作业法兰内.808-1/2″钻头五开.8-1/2″钻头五开.81提出8-1/2″钻头.提出8-1/2″钻头.828-1/2″钻头五开完毕.8-1/2″钻头五开完毕.83提出9-5/8″防磨套.提出9-5/8″防磨套.84下5-1/2″套管.下5-1/2″套管.85下5-1/2″套管到9-5/8″尾管上.下5-1/2″套管到9-5/8″尾管上.86拆钻井四通、防喷器组.拆钻井四通、防喷器组.87安装套管头护盖.安装套管头护盖.88安装套管头护盖完毕.安装套管头护盖完毕.89..902640mm2600mm36″钻头一开.2640mm2600mm36″钻头一开.9136″钻头一开完毕.36″钻头一开完毕.92提36″钻头.提36″钻头.93下30″导管.下30″导管.94固30″导管.固30″导管.95固30″导管完毕.固30″导管完毕.96割30″导管.割30″导管.97安装底座，把30″导管焊接在底座上.安装底座，把30″导管焊接在底座上.9826″钻头二开.26″钻头二开.99310m26″钻头二开完毕.310m26″钻头二开完毕.100310m提26″钻头.310m提26″钻头.101310m下20″套管.310m下20″套管.102310m下20″套管完毕.310m下20″套管完毕.103310m固20″套管.310m固20″套管.104310m固20″套管完毕.310m固20″套管完毕.105310m割20″套管.310m割20″套管.106310m安装调节底座及表层套管头，用反卡瓦固定20″套管.310m安装调节底座及表层套管头，用反卡瓦固定20″套管.107310m注密封脂，试压（3000PSI保压15分钟）.310m注密封脂，试压（3000PSI保压15分钟）.108310m安装升高短节.310m安装升高短节.109310m安装升高短节完毕.310m安装升高短节完毕.110310m安装20-3/4″钻井四通.310m安装20-3/4″钻井四通.111310m安装20-3/4″钻井四通完毕.310m安装20-3/4″钻井四通完毕.112310m安装20-3/4″双闸板防喷器.310m安装20-3/4″双闸板防喷器.113310m安装20-3/4″双闸板防喷器完毕.310m安装20-3/4″双闸板防喷器完毕.114310m安装20-3/4″万能防喷器.310m安装20-3/4″万能防喷器.115310m安装20-3/4″万能防喷器完毕.310m安装20-3/4″万能防喷器完毕.116310m下21-1/4″试压塞.310m下21-1/4″试压塞.117310m下21-1/4″试压塞到表层套管四通内.310m下21-1/4″试压塞到表层套管四通内.118310m防喷器试压（3000PSI保压15分钟）.310m防喷器试压（3000PSI保压15分钟）.119310m取出21-1/4″试压塞.310m取出21-1/4″试压塞.120310m下21-1/4″防磨套.310m下21-1/4″防磨套.121310m下21-1/4″防磨套到表层套管四通内.310m下21-1/4″防磨套到表层套管四通内.122310m17-1/2″钻头三开.310m17-1/2″钻头三开.123310m17-1/2″钻头三开.310m17-1/2″钻头三开.124310m17-1/2″钻头三开完毕.310m17-1/2″钻头三开完毕.125310m提17-1/2″钻头.310m提17-1/2″钻头.126310m下钻杆提21-1/4″防磨套.310m下钻杆提21-1/4″防磨套.127310m提出21-1/4″防磨套.310m提出21-1/4″防磨套.128310m下13-3/8″套管.310m下13-3/8″套管.129310m下13-3/8″套管完毕.310m下13-3/8″套管完毕.130310m拆升高短节底部螺栓，上提防喷器组.310m拆升高短节底部螺栓，上提防喷器组.131310m安装13-3/8″卡瓦式套管悬挂器及密封总成.310m安装13-3/8″卡瓦式套管悬挂器及密封总成.132310m安装13-3/8″卡瓦式套管悬挂器及密封总成完毕.310m安装13-3/8″卡瓦式套管悬挂器及密封总成完毕.133310m下移防喷器组，装升高短节底部螺栓.310m下移防喷器组，装升高短节底部螺栓.134310m在表层套管头侧翼4-1/16″法兰上连接泥浆循环管线.310m在表层套管头侧翼4-1/16″法兰上连接泥浆循环管线135310m固13-3/8″套管.310m固13-3/8″套管.136310m提升高短节、防喷器组.310m提升高短节、防喷器组.137310m拆升高短节、防喷器组.310m拆升高短节、防喷器组.138310m割13-3/8″套管.310m割13-3/8″套管.139装中层套管头.装中层套管头.140在中层套管头下法兰注密封脂，试压（10000PSI保压15分钟）.在中层套管头下法兰注密封脂，试压（10000PSI保压15分141装13-5/8″15000PSIX13-5/8″10000PSI转换法兰.装13-5/8″15000PSIX13-5/8″1000142装13-5/8″10000PSI钻井四通、防喷器组.装13-5/8″10000PSI钻井四通、防喷器组.143下13-5/8″试压塞.下13-5/8″试压塞.144下13-5/8″试压塞到中层套管四通内.下13-5/8″试压塞到中层套管四通内.145防喷器试压（10000PSI保压15分钟）.防喷器试压（10000PSI保压15分钟）.146取出13-5/8″试压塞.取出13-5/8″试压塞.147下13-5/8″防磨套.下13-5/8″防磨套.148下13-5/8″防磨套到中层套管四通内.下13-5/8″防磨套到中层套管四通内.14912-1/2″钻头四开.12-1/2″钻头四开.15012-1/2″钻头四开完毕.12-1/2″钻头四开完毕.151提12-1/2″钻头.提12-1/2″钻头.152下钻杆提13-5/8″防磨套.下钻杆提13-5/8″防磨套.153提出13-5/8″防磨套.提出13-5/8″防磨套.154下9-5/8″套管.下9-5/8″套管.155下9-5/8″套管完毕.下9-5/8″套管完毕.156在9-5/8″套管端部安装双公短节和9-5/8″心轴式套管悬挂器.在9-5/8″套管端部安装双公短节和9-5/8″心轴式套管悬1579-5/8″心轴式套管悬挂器座挂到中层套管四通内.9-5/8″心轴式套管悬挂器座挂到中层套管四通内.158用顶丝固定9-5/8″心轴式套管悬挂器.用顶丝固定9-5/8″心轴式套管悬挂器.159在中层套管头侧翼3-1/16″法兰上连接泥浆循环管线.在中层套管头侧翼3-1/16″法兰上连