服装工艺设计中英文对照表

1、服装中英文对照表请注意生产如下、Pls pay attention for production as below抽查、MEIYUE inspected夹圈捆条扭皱不均、 puckering and twisting at armhole piping /缝骨线阔窄、uneven topstitch on seam缝骨打褶、 pleated on seam夹圈起皱、fullness at sleeve armhole insertion缝骨起皱、seam puckering前幅front 后幅back 面料fabric 里料lining后筒位不直，谷皱不平服、 back slit not st

2、raight,crooking筒脚位长短、襟边有长短、uneven placket length后领筒位高低咀、hi low back slit襟边左右长短，襟脚圆角位不圆顺 unbalance lapel length, lapel corner not smooth前后幅脚边不平行、 front and back bottom not leveling装领前领窝缩皱/领咀不圆顺凸咀puckering at front neck seam, neckband end not align neck seam下级领脚扭皱不平服、puckering at collar band领圈位皱不平服、Co

3、llar a wrinkle is not flat领型样子不均匀、 collar shape is not pressingbroken seam at collar point, slanted collar领尖左右长短不对称、asymmetrical collar point领尖角爆止口、领尖角歪咀、领贴不均、领圈不圆顺、 fullness at collar placket, poor neck shaped, poor collar setting (not smooth)装介英凸咀、底贴反吐、poor cuff setting (pointed out at seam), expo

4、se under layer at cuff装后中拉链起(波浪)衫身偏紧、拉链尾转角位起皱 poor zipper setting on back body (wavy), too tight for wearing, puckering atzipper end领边捆条扭皱不均、 neck piping twisted, torque on neck piping装腰头裤身位缩皱、裤头咀位高低、puckering under waist seam, hi-low waistband装腰头裾身位缩皱、裾头咀位高低、puckering under waist seam, hi-low waist

5、band左右侧骨长短(+ - ) 1/2 寸、uneven inseam / outseam length (+-) 1/2”内长有长短、uneven length on inseam车脚线阔窄、top stitches uneven width on bottom脚间线落坑、run off stitches on bottom脚间线阔窄、 uneven top stitch at bottom长短脚、 panel length uneven of bottom脚位凹凸不平、 ugly hemming at bottom (at curve side)内浪骨位皱、脚口不平直没烫好、pucker

6、ing at rise seam, poor pressing at bottom (not leveling)脚叉长短、 uneven bottom slit length前筒起皱、puckering on front placket脚围细 3/4 寸至 1 寸Bottom width -3/4" to -1" 腰围细 3/4 " waist is small by 3脚口不直(顺) hem uneven/bottom uneven高低脚、 hem not leveled断线、broken stitches烫工不佳起镜痕(烫过火)pressing shine ,

7、 (over pressing / hard pressing)布疵、色纱、走纱、破洞、fabric fault , color yarn, run off yarn, broken hole 骨位间线驳线重线不佳、poor repairing stitches on double stitching面料有褶皱痕须烫好、crease line / folding line must improve by pressing腰驳幅位缩皱、puckering at waist panel seam 腰缝起皱, wrinkles at waistband facing腰贴扭皱不平K, waistban

8、d is not laying smoothly with drag lines骨位间线扭皱没烫好、puckering on seam (poor pressing)上术问题请及时改善，否则会影响出货、Pls revise these problems /as above,or can shipout跳线、skipped stitches线头、thread end飞毛欠干净 、fly yarn not cleanliness skate spade进度表 progress chart.打褶、pleated sewing衫身起皱、 winkle in body祥见尺寸表、 see table s

9、ize筒脚张开、 placket bottom spread open驳线不良、bad joined stitches间线不良、improper top stitching筒边钮门位不顺直、button placket edge长短筒、uneven length of placket面布车得太贴拉链难拉、fabric too closed to zipper拉链起波浪、zipper wavy拉链谷皱、zipper crock领、collar 领面松, wrinkles at top collar 领面紧 top collar appears tight 领面起泡, crumples atop

10、collar领不平衡（平服）unbalance collar领不对称、asymmetric colla歪领、uneven collar上领凸咀、nose on collar setting烂领尖、burst collar point领窝起皱 two much ease on bogy after collar setting领面凹凸不平、tented collar领歪斜欠圆顺、poorly shaped ot round neck领罗纹起波浪、rid neck puckering左右领宽不一致、uneven roll左右领圈不一致、 uneven collar point底领里起皱、wrink

11、les at collar band facing底领外露, collar band lean out of collar左右前领咀形状不一样、uneren lipel shapes前领口 常溶位太多、 too much easing at c.f neckline领脚扭皱不平服、collar band is twisting后领中太紧、collar too tight at cb领及前领不平顺、fullness at front collar and lapel领装的不服帖不平顺、neckline is not smooth后领圈有高低、high & low back neckV 咀

12、不正中、notch v off center前门领边不直、 edgr of front opening is crooked 或 front opening not straight前门领贴在下摆处外露、front facing exposed at bottom hem前门领贴短于大身、 front opening facing is shorter than body领圈拉松、neck was stretched突咀、excess extension袖和夹圈、sleeve &armhole下级领咀爆止口、 collar stand end seam broken左右夹圈有溶位不平服

13、、puckering at left/right armhole袖夹欠圆顺、 poorly shaped of round armhole衣袖走后、 sleeve running to back衣袖走前、sleeve running to front前袖骨拉松、too loose at front sleeve seam后袖骨过紧 too tight back sleeve seam介英（克夫）装的不好 poor cuff setting /省尖起泡, crumples at dart point底缝骨拉松、underarm seam was stretched /小肩起皱, puckers

14、at shoulders袖孑 L 不顺、 armhole setting not smooth /袖隆起皱、 creases at underarm袖顶缩拱不均有、 ease on sleeve cap is uneven上袖打褶皱、 pleated seam on sleeve前后幅（片）front / back谷钮筒、placket bubbling吊里、hiking at back lining too short前中拉链溶位太多、curve at cf zip （too much fullness at cf zip）前中拉链无溶位 （弓I起拱起不平® ）curve at c

15、f zipper because of no easing of zipper拉链牙与边距太贴，导致拉链拉合困难 tight clearance bctween the slider and the seam edge causing slider to operate with difficulty坏拉链 non functioned zipper漏拉链头、missing zipper puller拉链不能拉、zipper not movable后幅吊起、hiking at black /前幅吊起、hiking at front里布太大、lining too big里布太短、lining t

16、oo short里布小、lining too small里布太长、lining too long前后幅布纹不对称、crain lines are not match at & back panel左右前长不一致、 front length uneven袋 pocket上下袋唇不均、 pocket welt is uneven左右袋子装得高低不一致、both pocket set uneven装袋不平®、 不够方正、pocket not smooth/squared贴袋圆角位不圆顺、 pocket corner not smooth and round高低袋、high-low

17、pocket袋位左右高低、hi-low pocket袋盖不居中、pocket flap not centered oven pocket左右 口 袋形状不一致、both pocket shapes art uneven袋口有毛口、pocket opening is fray /口 袋变形、pocket shape distorted包边（捆边）binding断线、broken stitches跳线、skip stitches捆边扭曲不平顺、piping is twisting and not smooth捆边不均匀、 piping is uneven缩褶、pleats 后腰缩褶碎不均、 une

18、ven shriving at back waist seam克重、weight面料、抽纱 fabric draw yarn走纱、yarn run断线、broken stitches布疵、fabric defects色纱、color yarn粗纱、thick yarn抽纱、draw yarn破洞、broken hole断纱、broken yarn起泡、bubbling色差、color shading退色、color fading散 口、raw edge污渍、dirt mark油渍 oil stain,粉渍、chalk mark粉笔痕在钮位、chalk mark at button hole打枪

19、痕、cleaning marks贴纸痕、sticker marks缝线外露、thread visible outside 前筒起蛇（皱）wavy atpacket杂色纤维织入、color fiber woven褶痕、crease mark 起皱、buckle面料褶皱痕未烫好、fabric puckering not leveling衫身有明显的折痕、 visible pleated marks at body布料有死痕、permanent crease in the fabric成品外观有疵点、 fabric flaws on outside garments长短袖、 uneven lengt

20、h of sleeve /长短袖叉、 uneven sleeve placket针步密度不均、 uneven stitching density不均匀、uneven太细不平均、uneven size浪底十字骨错位、 unmatched crotch cross车丁珠、breading深浅色、uneven color扭脾、twist leg线头、uncut thread ends反光（止口反吐）、under ply turn out止 口 反骨、seam overturn车缝线落坑、run off stitches 前襟止 口 反吐、 facing leans out from front ed

21、ge毛粒、blub 、（上装、）领子、collar 肩、shoulder 袖子、sleeve 袖口、cuff后背约克，开叉Back yoke vent胸袋、 侧袋、 selvage pocket 、 side pocket拉链、隐形拉链、前身、侧缝、下摆。Zipper,invisible zipper,front part ,side seam,bottom省/Dart褶/pleat 褶皱、wrinkle 起皱 creases marks（下装）裤腰、裤祥， waistband ,belt loop门襟，里襟，fly,under fly（整烫）极光，shining烫工不好引致缝骨起镜面、pre

22、ssing too hard and mark seam shine整烫不良poor pressing起皱严重须翻烫、 excessive wrinkle that require pressing to over come蒸汽太多（太少） steam treating too much / too less烫痕iron mark熨烫过度 overpress熨烫不够 under press前褶位烫工不好、 pressing on front pleat not well成品烫工差、poor pressing on garments/pressed poorly at garment烫工起镜面、

23、shine caused by improper pressing烫痕，压痕 pressing mark乌纯结/扣hook & eye不牢、insecured脾开骨没烫开骨 gamts not well pressed under thigh,should be open press seam（颜色、）1/色差 color shade/color deviation线不酉己色、 unmatched colour of thread颜色偏浅（深）color is too light/dark欠问线、missing top stitching褪色，color fading褪色问题 colo

24、r fastness problem颜色组合错误wrong combo图案错误、wrong pattern错码、 wrong size indicated不正中、un centered辅助线外露、 support stitches visible颜色完全不同、total different color（包装）装箱错误（数量，配比）或者缺少东西（拷贝纸，纸板）wrong packing for （quantity,collocation） missing tissue paper, cardboard陵头写错、wrong shippingmark logo受损（陵头）、logo damaged边

25、粗糙、logo raw edges错码 wrong size indicated陵头单词模糊、label illegible脏污（严重）必须处理 Must clean the spots（terrible）里襟里起皱，creases at right fly双轨接线，stitch seam is uneven车脚、bottom hemming扭脚、twisted bottom脚口不齐 （平）leg opening is uneven脚边不均 / uneven width of Bottom门筒脚位不直、 placket sewing is curving at bottom门筒大小、uneve

26、n placket卷脚边扭皱不平直 wavy and twisting strolling hem脚边不平顺，侧骨脚口歪咀 bottom hem not smooth,side seam end not leveling at edge前后脚起蛇欠平直、not straight at front of body脚边有高彳氐、 up & down under of rib body衫脚欠平齐、up & down in bottom前筒弯曲、wavy placket前筒脚欠整齐、 stepped at bottom of front placket车线跳针甩线（车花）Car yar

27、n jump needle, take off the line（embroidery）脚位挑边跳针脱线、bottom skipped blinding stitches欠挑脚（挑脚跳线）bottom blinding stitch missing（skip）挑脚线露牙、 blinding stitch appeared at bottom hemming领 V 角位皱不平服 neck v angle wrinkle is not flatV领边有缩皱现象、collar point not uniform袖夹位谷起欠顺 / wavy on the armhole夹圈露缝线 / visible

28、linking in armhole袖夹爆缝 / holes on the armhole长短袖、 uneven length of sleeve领边车丁珠珠品 E 欠均匀称distance of every barding is not average尺寸欠稳定 / measurement is not good尺寸偏细 / measurement in not insecure门筒大小 / uneven placket线头未剪(不清) uncut threads/thread not trimmed浮线 / cut threads loosing(loose threads)间线不均匀、

29、stitching not uniform回针不牢、insecure back stitching左右袖长短、long & short between left & right sleeve袖 口 不直、the cuff is not straight喇叭口、flaring out裤头驳线不佳、 back stitching is found waistband高低裤头、high-low waistband裤头咀歪、 distorted waistband end裤头凸咀、waistband end not close to front fly裤头间线不均、 uneven ed

30、ge stitching on waistband裤头扭皱、waistband twisted后中裤头位起皱、 waistband near center back is puckering腰头位缩皱不均匀、 puckering under waist seam,non-uniform尺寸欠稳定、 measurement is not good尺寸偏细、 measurement in insecure吊带长度短、uneven length of hanger钮门散 口、raw edge on button hole钮不牢固、stud insecure（easily to pull out）衫身

31、条子欠顺直、not straight at rib body前襟长短、uneven length of front placket前襟吊里、shorter lining length on front facing（漏）打枣位置不对、bar-tack misplace /missing打枣位置不对、bar-tack misplace打枣起褶、fold fabric by improper bar-tack sctting拉链不顺畅、 zipper slider comes off/siding not smooth拉链裂开、zipper split领尖贴布不均匀（大小）uneven V-ins

32、et锈花线不满、emb. unclean thread end主陵不正中、main label off center漏挂牌 / 价钱牌、missing hangtag / price ticket欠士啤钮、missing spare buttonV领型不顺、V neck shape not smoothV 领不够尖、Vneck point not shape enough领型不佳、slanted neck shape / not smooth领边打褶、 pleat along neck ling前襟吊里、shorter lining length on front facing门筒位爆线、holes on the placketV 咀不正中、notch v off center里布有布疵、fabric defect on lining底爆止 口 raw edge inside大货有 LOT色明显、Big goods have a LOT of color is obvious面料走纱、fabric yarn run前幅条子不平服起皱、front blade not soothe wrinkle钮筒不直、front placket place position unsmooth脚贴兴里布位爆止口、seam broken on lining and hem facin